GYROOR C1Pro Folding Electric Scooter User Manual

Stem Assembly

1. Insert the stem into the designated slot.
2. Ensure the alignment arrows are correctly positioned.
3. Tighten the bolt located at the base of the stem.
4. Secure the lock mechanism.

Handlebar Assembly

1. Unscrew the assembly at the top of the stem.
2. Place the handlebar into position.
3. Reattach and tighten the quick release part.
4. Secure the quick release clamp.

Seat Post Assembly

Open the quick release on the seat post mount on the frame and insert the seat post. Adjust the seat height to a comfortable position and then close the quick release.

Luggage Basket Attachment

Remove the 4 mounting screws for the luggage basket located above the rear mudguard. Attach the luggage basket and secure it in place using the screws you removed.

⚠️ATTENTION!⚠️

Before riding, ensure the following:

• The front light, rear light, bell, and brakes are functioning correctly.
• The battery capacity displayed is sufficient.
• Tire pressure is adequate; the recommended pressure is 2.5 bar.

Overall Appearance

LCD Interface

Operating Instructions

1. Power On/Off: Single press the power button to turn on or off.
2. Switch Modes: Single press the 'M' button to cycle through Mode 1, Mode 2, and Mode 3, each corresponding to different speed limits.
3. Switch Lights On/Off: Double press the 'M' button to toggle the headlights.
4. Switch Mileage Display Content: Long press the function button (over 3 seconds) to cycle through display options in the mileage area: Cumulative mileage (ODO) → Single mileage (TRIP) → Battery voltage (UXX.X) → Failure code (ERR).

Notes on Display

• The single mileage (TRIP) resets every time the machine is restarted, while the accumulated mileage (ODO) continues to count.
• If no fault is detected, the fault code display is skipped.

5. Fault Code Display

When a fault is detected, the "ERR" icon will appear. Refer to the fault code table to identify the issue.

6. Battery Undervoltage

If the battery undervoltage warning sign appears, the scooter can still be ridden for a short distance, but charging is recommended immediately.

Fault Code Table

*Guide values, with a user weighing approx. 75 kg and with a fully charged battery on smooth, even road surfaces and under optimal temperature conditions.

Charging the Battery

The charging port is located at the rear end of the running board.

1. Open the protective cap over the charging port.
2. Ensure the charging port and charger are dry.
3. Make sure the Folding E-Scooter is turned off.
4. Connect the charging cable to the charging port.
5. Connect the charger's mains plug to a suitable wall socket (100 - 240V / 50 - 60 Hz).
6. The charging light on the charger will be red while charging.
7. The battery is fully charged when the light changes from red to green. Stop charging at this point.
8. Disconnect the charger from the mains and the Folding E-Scooter.

Battery Charger Model: XHK-800-4215, manufactured by Shenzhen Xin Heng Tyco Electronics Co.,ltd.

Warnings Regarding Battery Use

⚠️WARNING!⚠️

• Never remove the battery from the Folding E-Scooter.
• Charge the battery every 1 month for at least 1 hour, even if the E-Scooter has not been in use, to prevent capacity loss.
• Regular charging protects the battery from total discharge.
• Never heat the battery or throw it into an open fire.
• Never dispose of battery cells in household waste.
• Avoid moisture on the battery contacts.
• The optimal operating temperature for the battery is between 10° C and 30° C. Temperatures outside this range may reduce power output, range, and performance.
• Only use the supplied charger. Ensure the correct voltage supply (100 - 240V / 50 - 60 Hz).
• Do not charge if the charging cable is damaged. Contact customer service if damaged.
• Battery service life and performance depend on age, care, and usage frequency.
• For optimum battery life, charge and store the E-Scooter in a dry, clean environment, preferably between 7° C and 15° C.
• The Folding E-Scooter takes approximately 5 hours to charge. Permanently connecting the charger after charging can negatively affect battery life.
• Do not cover the E-Scooter or charger during charging.
• An over-discharged battery is irreparably destroyed and must be replaced for a fee. Batteries should never be completely discharged during operation.

Before you begin:

• Wear a safety helmet and protectors for your own safety.
• Wear comfortable leisure or sports clothing and flat shoes while riding.
• Before riding for the first time, ensure you have ample space and no obstacles.
• Fold the handlebar up and check the tire pressure.
• Check your E-Scooter before every journey (refer to "Maintenance and Care").
• Switch on the E-Scooter (refer to "Display Functions").
• Fold in the kickstand before riding to prevent accidents and injuries.

First steps

• Use the throttle twist grip to accelerate.
• Use the front and rear brakes to brake.
• You can choose between three speed levels.

Tips:

• Turn the rear light off after riding every time.
• Check the battery level before riding and charge if the power is low.
• To fold the E-scooter, pull the lock lever of the upright tube first.
• Refer to the "Using the battery" section for storage information.

General Care

• Before each ride, ensure all screws, lock levers, and quick release clamps are tightened.
• Make sure the tire pressure is correct.
• Use a soft, damp cloth for cleaning. For stubborn dirt, use plastic polish according to the manufacturer's instructions.

ℹ️NOTE!ℹ️

• Never use alcohol, naphtha, acetone, or other corrosive/volatile chemical solvents, as they can damage the scooter's surfaces and structure.
• Never clean the Folding E-Scooter with a strong jet of water or a high-pressure cleaner.

⚠️WARNING!⚠️

• Ensure the Folding E-Scooter is switched off and the charging socket cover is closed before cleaning to avoid electric shock or damage.

Storage

• Store your Folding E-Scooter in a dry and cool place.
• A well-maintained battery provides good performance. Charge the battery after each ride and avoid operating on an empty charge. Battery performance may decrease at low temperatures.

ℹ️NOTE!ℹ️

• Do not store the scooter outdoors. Exposure to sunlight or extreme temperatures can accelerate aging of plastic parts and reduce battery life.
• Turn off the Folding E-Scooter after each ride and charge the battery. Over-discharged batteries can be irreparably damaged. Damage from incorrect use is not covered by warranty. Removing or opening the battery is not permitted.

Additional Warnings:

• Devices are not intended for use at elevations greater than 2000 m above sea level.
• Prolonged exposure to UV Rays, Rain, and the Elements may damage enclosure materials. Store indoors when not in use.
• WARNING – Risk of Fire – No User Serviceable Parts.
• (French translation) Les appareils ne sont pas destinés à être utilisés à des altitudes supérieures à 2000 m au-dessus du niveau de la mer. Une exposition prolongée aux rayons UV, à la pluie et aux éléments peut endommager les matériaux de l'enceinte, stocker à l'intérieur lorsqu'ils ne sont pas utilisés. AVERTISSEMENT- Risque d'incendie et de choc électrique - Aucune des pièces ne peut être réparée par l'utilisateur.

Adjusting the Brake Callipers

• Check regularly to ensure brake callipers are properly adjusted.
• You will need the Allen key and a rubber band.
• 1. Slightly loosen the two brake calliper mounting bolts until the calliper can be moved.
• 2. Use the rubber band to hold the brake lever, centering the brake calliper.
• 3. Tighten both brake calliper mounting bolts again. After removing the rubber band, check if the wheel moves freely.

ℹ️NOTE!ℹ️ The adjustment procedure is the same for both front and rear brakes.

Tautening/Loosening the Brake Cables

1. To adjust a brake cable, first loosen the lock nut on the corresponding brake lever.
2. Turn the adjusting nut to tighten the brake cable (reducing distance between brake shoes and disc) or loosen it (increasing distance).
3. After adjustment, tighten the lock nut to secure the setting.

ℹ️NOTE! The setting is correct if the brake shoes are a maximum of 1 mm from the brake disc.