Alphacool Eiswolf 2 All-In-One GPU Cooler
Installation and Safety Manual
Safety Information
READ THE SAFETY INSTRUCTIONS BEFORE STARTING THE INSTALLATION
- Not suitable for children under 6 years of age (contains small parts that may be swallowed).
- Do not operate cooling components without ensuring that coolant flows unrestricted. Insufficient coolant can lead to very hot parts and could cause burns.
- Coolers devoid of coolant can damage hardware. Always be sure to check your system often.
- Please note that no tools such as spanners, pliers or similar may be used to tighten the fittings! Fittings connected to plastic parts can be damaged if over tightened with tools! Cracks or other damage caused by this as well as damage caused by leaking coolant are not covered by the warranty!
- Only use fittings with a sealing O-ring! Due to the sealing ring, tightening by hand is enough! In exceptional cases, the manual will clearly point out when to use of tools!
- If not already done, please check the function of your hardware and the cooling system (tightness, pump function and fan). This will minimize the effort involved in finding possible sources of error. ALPHACOOL INTERNATIONAL GMBH does not assume the warranty of the manufacturer of the electronic parts and components. The cooling system is installed at your own risk.
- The screws should not be overtightened. If you have overtightened the screws, the retaining bolts may loosen, and the cooler will no longer be able to rest evenly on them.
- Fittings with a thread length of 8 mm may result lower flow rates.
- We recommend a leak test before mounting / installing the cooler. The water pressure in the water cooling circuit must not exceed 0.8 bar.
- Make sure that the cooler touches all components to be cooled with heat-conducting paste and / or heat-conducting pads.
- Only use distilled water or ALPHACOOL CAPE KELVIN CATCHER (CKC) in your cooling circuit. Damage caused by unsuitable coolant is not covered by the warranty!
SPECIFIED NORMAL OPERATION
ALPHACOOL INTERNATIONAL GMBH cooling components are only approved for cooling computer components. The warranty is void if the components are used in any other way.
Warranty
- Information, drawings, illustrations, technical data, descriptions of weight, dimensions and performance contained in brochures, catalogues, circulars, advertisements or price lists are for information purposes only. We assume no liability for the correctness of this information. With regard to the type and scope of delivery, only the information contained in the order and order confirmation is decisive.
- Insofar as a defect covered by warranty exists, you are entitled within the framework of the statutory provisions to demand subsequent performance, to withdraw from the contract or to reduce the purchase price. The limitation period for warranty claims for the delivered goods is two years from receipt of the goods if you are a consumer (§ 13 BGB). If you are an entrepreneur (§ 14 BGB), the provision that the period of limitation is only one year shall apply.
- The warranty claim is only valid in connection with the original invoice, the sales receipt or a confirmation from ALPHACOOL INTERNATIONAL GMBH of the warranty claim.
- It is solely at the discretion of ALPHACOOL INTERNATIONAL GMBH to repair or replace the defective product or defective components. The replaced product or component becomes the property of ALPHACOOL INTERNATIONAL GMBH.
- All warranty claims are handled by ALPHACOOL INTERNATIONAL GMBH or by authorized dealers. If the repair is carried out by a non-authorized or authorized person, ALPHACOOL INTERNATIONAL GMBH assumes neither costs nor liability, unless the repair has been agreed in advance with ALPHACOOL INTERNATIONAL GMBH.
- ALPHACOOL INTERNATIONAL GMBH will not bear any costs arising from a possible conversion of the products.
- ALPHACOOL INTERNATIONAL GMBH's warranty does not include the following:
- 7.1. Regular inspections, maintenance and repair or replacement of wearing parts
- 7.2. Incorrect operation or defects due to incorrect installation.
- 7.3. Damage caused by storm, water, fire, excess voltage, force majeure or war, faulty connection to the mains, insufficient or faulty ventilation or other reasons beyond the control of ALPHACOOL INTERNATIONAL GMBH.
- 7.4. Damage caused by transport or improper packaging.
- The rights of the consumer applicable in the respective country, e.g. claims against the seller, as laid down in the sales contract, are not affected by this warranty declaration. ALPHACOOL INTERNATIONAL GMBH, its subsidiaries and distributors are not liable for direct or indirect damages or losses, unless mandatory legal provisions provide otherwise.
- ALPHACOOL INTERNATIONAL GMBH does not assume the warranty of the manufacturer of the electronic parts and components. The installation of the cooler is at your own risk.
Contact an authorized disposal company in your country. Disposal with household waste (unsorted waste) or similar facilities for the collection of municipal waste are not permitted. ♻️
Mounting Material
1x Eiswolf 2 |
1x Mounting set graphics card |
1x Radiator (AIO version only) |
1-3 Fans Depending on version (AIO version only) |
5V Digital RGB Adapter |
Type varies by version 1 - 2 Fan Y-Adapter (AIO version only) |
1x Plug Tool |
For each fan 4x screw M3x30 (AIO version only) |
For each fan 4x screw M3x5 (AIO version only) |
1x Allen key |
Technical Details
Pump Specifications (Demineralised water):
| Model series | DC-LT 2 |
|---|---|
| Voltage | 12V DC |
| Speed (+/- 10%) | 2600 rpm (+/- 10%) |
| Electricity | 0.33A |
| Power | 4W |
| Liters / hour | 75l/h |
| Head pressure | 0,95m |
| L x W x H | 130 x 225 x 46 mm |
| Material cooler base | Nickel-plated copper |
| Material housing | PMMA |
| Connections | 2 x G1/4" |
Radiator Specifications:
| Model series | NexXxoS |
|---|---|
| Material | Copper, Brass (Threads) |
| Model variants: ST30 240 | Dimensions: 278 mm x 124 mm x 30 mm 398 mm x 124 mm x 30 mm |
| ST30 360 |
Fan Specifications:
| Model series | Eiszyklon Aurora LUX PRO Digital RGB |
|---|---|
| Model variants 120mm | Power: 4,8W (+2W LEDs) Fan Voltage: 12V DC LEDs Voltage: 5V DC Rotational speed: 800 - 2000 U/min. Airflow volume: Max. 104,49 m3/h Static pressure: 2 mm H2O Noise level: 24,1 - 35,6 dB(A) |
Assembly Instructions
Radiator and Fan Assembly
Mount the cooler as described in the manual for graphics cards cooler.
RADIATOR ASSEMBLY
Fans pushing
Fans pulling
Connecting the Fans
Fan Connection Diagram:
A 4-pin fan connector is used for power and speed control via the motherboard or fan controller. Digital RGB LEDs require a 5V supply voltage; exceeding this can destroy the LEDs.
Pump Connection:
Plug the 3-pin connector into a free fan connector on your motherboard. Ensure the voltage is set to 12V in the BIOS. This is not necessary for PWM connections.
Combining Eiswolf 2 with Eisbaer
- Disconnect the tube at the quick connector. Please note that 1 to 2 drops of coolant may leak out when disconnecting.
- Connect the tubes of the individual components. This could be, for example, Eisbaer solo and or an additional radiator. It is not possible to connect the quick couplings the wrong way. Alphacool offers prefilled radiators with pre-mounted quick connectors for direct mounting on the Eiswolf 2 or the Eisbaer Aurora. Please contact your dealer or visit the Alphacool Shop for more information.
For more information, please visit: WWW.ALPHACOOL.COM/SHOP
