TONSTAD
Product by IKEA
Safety Warnings
⚠️ WARNING: Serious or fatal crushing injuries can occur from furniture tip-over. ALWAYS secure this furniture to the wall using tip-over restraints.
To further reduce the risk of serious injury and death from tip-overs:
- Place heaviest items ? in the lower drawer.
- Do not set TVs or other heavy objects on top of this product.
- Never let children ? climb or hang on drawers, doors, or shelves.
This warning is translated into multiple languages including Spanish, Portuguese, Chinese, Arabic, Thai, Korean, Japanese, Bahasa Indonesia, and Bahasa Malaysia.
Tools and Hardware Overview
The following tools are depicted for assembly:
- Screwdrivers (Phillips ➕ and flathead ➖)
- Hammer ?
- Pencil ✏️
- Drill ? with drill bits: Ø 8 mm (5/16") and Ø 3 mm (1/8")
- A tool resembling a staple gun or rivet gun (used for cam locks)
- Wrench ?️ (for adjustable feet)
Key hardware components include:
- Screws (various types and sizes, e.g., 10048881, 118331, 109049, 109567, 159991, 106603)
- Wall plugs (e.g., 10087223)
- Dowels (e.g., 101350)
- Cam locks and studs (e.g., 113434, 120076, 10048881)
- Brackets for wall mounting (e.g., 106989, 102553, 151706, 151705)
- Adjustable feet
Diagrams on page 20 illustrate wall mounting procedures for different wall types (A: Solid wall, B: Hollow wall, C: Solid wood) with specific drill bit sizes and screw/plug recommendations.
Assembly Steps
Step 1: Attach mounting rails to side panels
Take the left (L) and right (R) side panels. Attach two mounting rails (part 10127303) to the inner surface of each side panel using six screws (part 10048881) per panel. Ensure the rails are oriented correctly as shown in the diagram.
Visual cue: Hand icons indicate the correct orientation and placement of screws.
Step 2: Attach wall mounting brackets to side panels
Take the two wall mounting brackets (part 106989). Attach one bracket to the top rear edge of each side panel using two screws (part 109049) and two wall plugs (part 100823) per bracket. The bracket should be positioned towards the outer edge of the panel.
Visual cue: A diagram shows the bracket being screwed into place.
Step 3: Attach connecting panels to the right side panel
Take the right side panel (R) with attached rails. Attach two horizontal connecting panels to the inner side of the right panel using six screws (part 10127303) and six cam lock studs (part 10048881) per panel. The diagram shows inserting the studs and then securing them with the cam locks.
Visual cue: Arrows indicate the direction of insertion and tightening.
Step 4: Attach connecting panels to the left side panel
Take the left side panel (L) with attached rails. Attach the two horizontal connecting panels to the inner side of the left panel using six screws (part 10127303) and six cam lock studs (part 10048881) per panel. This mirrors Step 3.
Visual cue: Arrows indicate the direction of insertion and tightening.
Step 5: Connect drawer front support pieces
Take two drawer front support pieces. Align them with the corresponding slots on the partially assembled frame. Insert two screws (part 109567) to secure them. The diagram shows a close-up of how the pieces connect and are screwed in.
Visual cue: Arrows show the direction of connection and insertion of screws.
Step 6: Connect drawer side pieces
Take two drawer side pieces. Align them with the corresponding slots on the partially assembled frame. The diagram shows how these pieces slot into place.
Visual cue: Arrows indicate the direction of connection.
Step 7: Connect more drawer side pieces
Take two more drawer side pieces. Connect them to the existing structure, extending the frame. Arrows indicate the direction of connection.
Step 8: Connect drawer back pieces
Take two drawer back pieces. Connect them to the structure, completing the main frame. Arrows indicate the direction of connection.
Step 9: Insert internal horizontal panels
Insert twelve dowels (part 101350) into the designated holes on the internal structure. Then, slide the four internal horizontal panels into place, aligning them with the dowels and grooves.
Visual cue: Arrows show the direction of insertion for dowels and panels.
Step 10: Add top panels
Place the four top panels onto the assembled structure. Insert eight dowels (part 101350) into the designated holes on the top edges of the side and back panels, then align the top panels and press down firmly.
Visual cue: Arrows indicate the direction of placement and insertion of dowels.
Step 11: Attach frame supports
Take the long frame support pieces. Attach them to the top and bottom of the main structure using six screws (part 118331) per piece. The diagram shows the placement and screwing action.
Visual cue: Arrows show the direction of screwing.
Step 12: Connect frame pieces with dowels
Take the remaining frame pieces. Insert two dowels (part 101350) into the designated holes on one piece, then align and connect it to the other frame piece. This forms the base structure.
Visual cue: Arrows show the direction of connection.
Step 13: Prepare for cam lock assembly
Two frame pieces are shown being prepared for connection. Hand icons indicate the action of holding the pieces steady.
Step 14: Assemble base frame
Connect the prepared frame pieces to form the base of the unit. Hand icons indicate the action of holding the pieces steady during connection.
Step 15: Install cam locks
Install six cam lock mechanisms (part 113434) into the designated holes on the assembled frame. The diagram shows the cam lock being inserted and rotated to secure.
Visual cue: A rotating arrow indicates the tightening action.
Step 16: Attach drawer slide brackets (part 1)
Attach four drawer slide brackets (part 151706) and four corresponding studs (part 151705) to the designated positions on the internal frame. The diagram shows the bracket and stud being screwed into place.
Visual cue: Arrows show the direction of screwing.
Step 17: Attach drawer slide brackets (part 2)
Attach nine dowels (part 101350) into the designated holes on the internal frame. This prepares for the next stage of assembly.
Visual cue: Arrows indicate the direction of dowel insertion.
Step 18: Attach drawer slide brackets (part 3)
Attach four drawer slide brackets (part 151706) and four corresponding studs (part 151705) to the designated positions on the internal frame. This is similar to Step 16, likely for a different set of slides.
Visual cue: Arrows show the direction of screwing.
Step 19: Attach drawer front support
Attach one support piece (part 153549) to the front of the main unit using the indicated screws. The diagram shows the alignment and screwing action.
Visual cue: Arrows show the direction of connection and screwing.
Step 20: Attach drawer front base
Attach the drawer front base panel using five screws (part 159991). The diagram shows the alignment and screwing action.
Visual cue: Arrows show the direction of connection and screwing.
Step 21: Attach adjustable feet
Screw five adjustable feet into the base of the unit using the provided wrench (part 190459). Arrows indicate the screwing direction and the ability to adjust height.
Visual cue: Arrows show the direction of screwing and adjustment.
Step 22: Install drawer slide mechanisms
Install the drawer slide mechanisms onto the side panels of the main unit. The diagram shows two sets of slides being attached, likely for the upper drawers, using screws.
Visual cue: Arrows indicate the direction of attachment.
Step 23: Final frame check
A cross symbol 'X' is shown, possibly indicating a check or a point to avoid. The main frame is shown.
Step 24: Wall Mounting Instructions
Important: The supplied screws and plugs are suitable for most solid (A) and hollow (B) walls. For solid wood (C) walls, use screws without plugs. If you are uncertain about your wall type or the correct fixings, seek professional advice.
Diagrams illustrate:
- Type A (Solid Wall): Drill a hole (Ø 8 mm / 5/16"), insert plug, and screw.
- Type B (Hollow Wall): Drill a hole (Ø 8 mm / 5/16"), insert plug, and screw. Depth of hole is approximately 70 mm (2 3/4").
- Type C (Solid Wood): Drill a pilot hole (Ø 3 mm / 1/8") and screw directly. Depth of hole is approximately 30 mm (1 1/4").
Step 25: Attach wall mounting brackets to unit
Attach two wall mounting brackets (part 100823) and two corresponding studs (part 109567) to the top rear of the main unit. The diagram shows them being screwed into place.
Visual cue: Arrows show the direction of screwing.
Step 26: Assemble drawer sides
Take two drawer side pieces (2x) and four drawer back pieces (4x). Assemble the drawer sides and backs. The diagram shows how these pieces connect.
Visual cue: Arrows indicate the direction of connection.
Step 27: Attach drawer front support
Attach a drawer front support piece to the assembled drawer sides. The diagram shows the alignment and connection.
Visual cue: Arrows indicate the direction of connection.
Step 28: Attach drawer front panel
Attach the drawer front panel to the assembled drawer structure using four screws (part 10096669). The diagram shows the alignment and screwing action.
Visual cue: Arrows show the direction of connection and screwing.
Step 29: Install drawer slide mechanisms on drawer
Install four drawer slide mechanisms (part 120076) onto the sides of the drawer. The diagram shows them being attached with screws.
Visual cue: Arrows show the direction of attachment.
Step 30: Attach drawer handle/pull
Attach the drawer handle/pull (parts 10083447, 10091526) to the drawer front using one screw (part 106603). The diagram shows the screw passing through the drawer front into the handle.
Visual cue: Arrows show the direction of screwing.
Step 31: Insert drawer slides into main unit
Slide the assembled drawer slides into the corresponding runners on the main unit. Arrows indicate the direction of insertion.
Step 32: Insert drawers and check
Insert the assembled drawers into the main unit. A close-up shows a mechanism that clicks into place, indicating the drawer is secured. A warning icon ⚠️ and a "no mobile phone" icon are shown, possibly related to the drawer mechanism or safety.
Visual cue: "Click!" text indicates successful engagement. Arrows show insertion.
Step 33: Final drawer insertion
Slide the drawer into the main unit. An arrow indicates the direction of insertion.
Step 34: Insert remaining drawers
Insert the remaining drawers into their respective slots in the main unit. Arrows indicate the direction of insertion.
Step 35: Insert final drawers and check
Insert the last set of drawers into the main unit. A close-up shows a mechanism that clicks into place, indicating the drawer is secured. "Click!" text indicates successful engagement.
Visual cue: Arrows show insertion.
Step 36: Final placement and adjustment
The assembled TONSTAD unit is shown. An information icon ℹ️ is present. A diagram shows how to adjust the feet for leveling. Arrows indicate vertical adjustment.
Visual cue: Arrows show up/down adjustment.
