GROWNSY N9 Bottle Warmer User Manual

Introduction

Please read this user manual carefully before using and save it for future reference.

*Note: Do not touch the device while it's working to prevent burns.

Component Introduction

• Lift-out Basket
• Select Initial Temp button
• Select Bottle button
• Select Volume button
• Sterilize button
• Power button [power-symbol]

Power On

1. After powering on, all lights will be on for 1 second, and there will be a beep, then it will enter standby mode, and all indicators will go out.
2. In the standby state, press the power button [power-symbol], and there will be a beep to indicate it enters the "waiting for operation" state. If there is no operation within 1 minute, the product will automatically return to standby state.

This bottle warmer has a smart memory function, remembering the last setting for convenience.

Warm Milk Function

1. While the device is in the "waiting for operation" state: Press the "Material", "Temperature", and "Volume" buttons to select the desired settings, then press the power button [power-symbol] to start working.
2. In the working state, the selected indicator lights will be steadily on. The milk will be heated to approximately 98.6°F (37°C). After the milk is ready, the machine beeps 6 times and enters the keep warm mode for 2 hours.
3. In the keep warm mode, all indicator lights will be turned on. After keeping the milk warm for 2 hours, the device will beep once and enter the shutdown state, with all indicator lights turning off.

Note: In the working state, you can press the "Material", "Temperature", "Volume" buttons to reset at any time, then press the power button [power-symbol] again to re-enter the working state.

Warm tip: Before feeding, gently shake the bottle and sprinkle a few drops on the inside of your wrist to check the milk temperature.

Disinfection Function

1. Pour distilled water into the chamber (not exceeding the maximum water line).
2. While the device is in the "waiting for operation" state, press the "Sterilize" button, and the "Sterilize" indicator light will flash.
3. Press the power button [power-symbol] again. The device will beep once and start working, and the "Sterilize" indicator light will light up. Disinfection time is 10 minutes (after boiling water).
4. When the countdown is over, the device will beep five times and automatically turn off. If the water dries out while working, the power will automatically turn off.
5. When you hear five "BEEP" sounds, please carefully take out the bottle to avoid getting burned.

Note: Press the disinfection button and press the power button [power-symbol] to disinfect for 10 minutes.

Operation Steps Diagram Description

The diagram illustrates the sequence of operations:

1. Pour water to the Max line.
2. Select initial temperature (Room, Refrig, Frozen).
3. Select bottle material (Bag, Plastic, Silicone).
4. Select volume (1-3 oz, 4-6 oz, 7+ oz).
5. Press the power button [power-symbol] to start heating.
6. The device beeps when milk is ready and enters keep warm mode for 2 hours.
7. For disinfection, press the "Sterilize" button and then the power button [power-symbol].

Quick Reference Guide

This section provides approximate heating times based on initial temperature, bottle material, and volume.

Notes:

• Pour distilled water into the bottle warmer to the Max line.
• When the milk is ready, all indicator lights will turn on. The warmer will keep the milk warm for up to 2 hours.
• This reference sheet does not provide exact times as initial temperature, bottle material, and ambient temperature will impact final milk temperature.
• Check milk temperature by sprinkling a few drops on the inside of your wrist.
• If milk temperature is lower than expected, place the bottle back in the chamber to continue heating for 0.5/1 minute.
• If milk temperature is higher than expected, cool the milk before feeding.
• Descale the bottle warmer regularly to prevent malfunctions like automatic shutdown or inability to warm milk.

Notice

• Default settings are: Plastic, Refrig, 1-3 oz. You can change settings as desired.
• During operation, you can press the "Material", "Initial temp", "Volume" buttons to reset at any time.
• During operation, you can press the power button [power-symbol] to shut down.

Caution

The water in the bottle warmer might be hot after finishing warming milk/baby food. Be careful, as hot water can cause serious burns.

Maintenance

Scale may form after use. It is recommended to descale the bottle warmer regularly to ensure it continues to work efficiently.

Warranty: one-year warranty