Manuals+

ErGear 55" Electric Standing Desk Instruction Manual

Models: EGESD6B-3 / EGESD6V-3

Technical Support

(US/CA) 1-800-651-9525 Mon-Fri, 8am-8pm (CST)

(UK) 44-808-196-3875 Mon-Fri, 2pm-10pm (UTC)

Other Info: support@ergear.com

Website: https://ergear.com

Specifications

  • Height Adjustment Range: 28.3"–46.5" (72–118cm)
  • Power Input: 100V–240V
  • Max. Speed: 20mm/s
  • Operating Noise: <55dB
  • Max. Load: 176 lbs / 80 kg

Supplied Parts and Hardware

Step 1

  • 01 x 1: Crossbar
  • 02 x 1: Left Desk Leg
  • 03 x 1: Right Desk Leg
  • 04 x 2: Leg Base
  • A x 8: Bolt
  • B x 4: Bolt
  • F x 1: Large Allen Wrench 3/16" (5mm)

Step 2

  • 05 x 2: Side Plate (with 'Arrow Outwards' marking)
  • 06 x 1: Transmission Rod
  • B x 4: Bolt
  • E x 1: Small Allen Wrench 5/64" (2mm)
  • F x 1: Large Allen Wrench 3/16" (5mm)
  • J x 11: Rubber Pad

Step 3

  • 07 x 1: Desktop
  • C x 29: Screw
  • D x 6: Wood Dowel Pin
  • G x 2: Headset Hook
  • H x 4: Desktop Panel Connector
  • 08 x 1: Left Drawer Side Plate
  • 09 x 1: Right Drawer Side Plate
  • 10 x 1: Controller

Step 4

  • 11 x 1: AC Adapter
  • I x 2: Cable Clip

Step 5

  • 12 x 1: Fabric Drawer
  • 13 x 1: Drawer Bottom Board
  • K x 1: Drawer Knob
  • L x 1: Bolt

Assembly Instructions

Step 1: Assembling and Connecting the Desk Legs

Warning: This step involves heavy components. Assistance may be needed.

  1. Attach the Crossbar (01) to the Left Desk Leg (02) and Right Desk Leg (03) using Bolts (B). Ensure the legs are oriented correctly. Use the Large Allen Wrench (F) to tighten.
  2. Attach the Leg Bases (04) to the bottom of the Left and Right Desk Legs using Bolts (A). Use the Large Allen Wrench (F) to tighten.

Step 2: Attaching the Side Plates and the Transmission Rod

  1. Attach the Side Plates (05) to the top of the assembled desk legs using Bolts (B). Ensure the 'Arrow Outwards' marking on the Side Plate faces outwards. Use the Large Allen Wrench (F) to tighten.
  2. Before inserting the Transmission Rod (06), measure the heights of the two desk legs to ensure they are level. If not, insert the Transmission Rod (06) into the hole in the left leg. Turn the rod anti-clockwise to raise the left leg or clockwise to lower it until it is level with the right leg. Ensure the set screw on the transmission rod faces out.
  3. Smoothly connect the other end of the Transmission Rod (06) to the motor drive shaft on the right leg.
  4. Secure the transmission rod to the motor drive shaft by turning the set screw clockwise using the Small Allen Wrench (E).
  5. Loosen the coupling nut on the transmission rod. Once the rod is properly seated, tighten the coupling nut to fine-tune the transmission rod fit.

Step 3: Assembling and Attaching the Desktop

  1. Assemble the Desktop (07) by inserting Wood Dowel Pins (D) into the pre-drilled holes. Attach Desktop Panel Connectors (H) to the desktop using Screws (C). (Drill not included)
  2. Carefully place the assembled desktop onto the desk frame, aligning the holes. Attach the desktop to the frame using Screws (C). (Drill not included)

Step 4: Attaching Hooks, Controller, and Drawer Side Plates

  1. Attach the Headset Hooks (G) to the underside of the desktop using Screws (C). (Drill not included)
  2. Attach the Controller (10) to the underside of the desktop using Screws (C). (Drill not included)
  3. Attach the Left Drawer Side Plate (08) and Right Drawer Side Plate (09) to the underside of the desktop using Screws (C). (Drill not included)

Step 5: Connecting the Cables

  1. Connect the AC Adapter (11) to the desk's control box.
  2. Route and secure all cables neatly using Cable Clips (I) to prevent tangling and damage.

Step 6: Assembling the Drawer

  1. Assemble the Fabric Drawer (12) by inserting the Drawer Bottom Board (13) and attaching the Drawer Knob (K) using a Bolt (L). (Phillips Screwdriver not included)

Step 7: Inserting the Drawer

  1. Slide the assembled Fabric Drawer (12) into the drawer side plates attached to the desktop.

Using the Controller

  • Save Current Height Setting: Short-press the 'S' button, and the display will flash. Press the '1', '2', or '3' button to save the current height setting to that button.
  • Select Height Setting 1: Press the '1' button, and the desk will move to the height that was previously set for that button.
  • Select Height Setting 2: Press the '2' button, and the desk will move to the height that was previously set for that button.
  • Select Height Setting 3: Press the '3' button, and the desk will move to the height that was previously set for that button.
  • Raise the Desk: Press the '▲' button to raise the desk continuously until it reaches the highest position of 46.5" (118cm) or the button is released.
  • Lower the Desk: Press the '▼' button to lower the desk continuously until it reaches the lowest position of 28.3" (72cm) or the button is released.

Settings

  • Change Display Height Units: Press and hold the 'S' button until a flashing 'S-' is displayed. Press 'S' again, and 'Un' is displayed. Press 'S' to select it, press '▲' or '▼' to switch between 'IN' (imperial) and 'SI' (metric), and press 'S' to save your choice.
  • Change Collision Detection Sensitivity: Press and hold the 'S' button until a flashing 'S-' is displayed. Press 'S' again, and 'Un' is displayed. Press '▲' or '▼' to switch to 'CF' and press 'S' to select it. Press '▲' or '▼' to switch between off, low, normal, and high sensitivity. Press 'S' to save your choice.
  • Reset: Press and hold the '▼' button for 5 seconds, and the screen will show 'RES.' Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes

Hot (Overheating Protection)
When the motor has been working continuously for 2 minutes, it will stop operating to prevent damage from overheating. Wait for at least 18 minutes before making any further height adjustment.
E10 (Sensor Malfunction Warning)
Motor safety sensor cannot be detected. Power off, check the connection between the motor and controller, and power back on again.
E20 (Overloading Warning)
Max load exceeded. If raising the desk, remove items from the desk and try again. If lowering the desk, power off, remove items from the desk, power back on, and try again.
E02 (Operation Status Warning)
The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use.
E32 (Overvoltage Protection)
Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E31 (Undervoltage Protection)
Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E60 (Unequal Leg Height Warning)
Power off the desk and check whether the left and right legs are at the same height. Adjust if necessary by following the instructions. Power on again.
Cable Disconnection Warning
Check motor and controller cable connections. Normal operation should return once all connectors are properly connected.
Models: EGESD6V-3 Electric Standing Desk with Drawer, EGESD6V-3, Electric Standing Desk with Drawer, Standing Desk with Drawer, Desk with Drawer, Drawer

PDF preview unavailable. Download the PDF instead.

C1jNBAoL-VL Adobe Illustrator 25.0 (Windows) iLovePDF

Related Documents

Preview ErGear 55-inch Electric Standing Desk Instruction Manual EGESD6B-1 EGESD6V-1
This instruction manual provides comprehensive assembly, operation, and troubleshooting guidance for the ErGear 55-inch Electric Standing Desk models EGESD6B-1 and EGESD6V-1. Learn how to set up your adjustable height desk, use the controller for height adjustments and settings, and understand error codes for maintenance.
Preview ErGear 55" Electric Standing Desk Instruction Manual EGESD6B-4 EGESD6V-4
Comprehensive instruction manual for the ErGear 55" Electric Standing Desk models EGESD6B-4 and EGESD6V-4. Includes detailed assembly steps, parts lists, controller usage, settings adjustment, and troubleshooting error codes for optimal desk operation and maintenance.
Preview ErGear 55" Electric Standing Desk Instruction Manual
Comprehensive instruction manual for the ErGear 55" Electric Standing Desk (models EGESD6B, EGESD6V, EGESD6N), covering assembly, operation of the electric controller, height adjustment settings, collision detection, and troubleshooting common error codes for optimal desk functionality.
Preview ErGear Electric Standing Desk Instruction Manual
Comprehensive instruction manual for ErGear Electric Standing Desk models EGESD6B, EGESD6V, EGESD6N, EGESD7B, EGESD7V, EGESD7N. Includes detailed assembly steps, controller usage, height adjustment, and troubleshooting error codes for optimal desk operation.
Preview ErGear 55-inch Electric Standing Desk Instruction Manual
This instruction manual provides comprehensive assembly steps, specifications, and controller usage guidelines for the ErGear 55-inch Electric Standing Desk models EGESD6B-1 and EGESD6V-1. Learn how to set up your height-adjustable desk, operate its functions, and troubleshoot common issues.
Preview ErGear Electric Standing Desk Instruction Manual - Assembly and Operation Guide
Comprehensive instruction manual for the ErGear Electric Standing Desk (Models EGESD8B, EGESD8V). Learn how to assemble, operate, and troubleshoot your height-adjustable desk.
Preview ErGear Electric Standing Desk Instruction Manual
Comprehensive instruction manual for the ErGear Electric Standing Desk, covering assembly, operation, and troubleshooting for models EGESD9B and EGESD9V.
Preview Ergear Electric Standing Desk Assembly and User Manual
Comprehensive guide for assembling and using the Ergear 48" / 63" Electric Standing Desk (Models EGESD5B, EGESD5V, EGESD5N, EGESD7B, EGESD7V, EGESD7N). Includes step-by-step instructions, specifications, controller functions, and troubleshooting error codes.