Manuals+

ErGear 55" Electric Standing Desk Instruction Manual

Models: EGESD6B / EGESD6V / EGESD6N

Tools Needed (Not Included)

Specifications

Supplied Parts and Hardware

Step 1 Parts

Step 2 Parts

Step 3 Parts

Step 4 Parts

Step 5 Parts

Assembly Instructions

Step 1: Assembling and Connecting the Desk Legs

HEAVY! You may need assistance with this step.

  1. Attach the crossbar (01) to the left desk leg (02) and right desk leg (03) using bolts (A) and the large Allen wrench (C). Ensure the crossbar is securely fastened to both legs.
  2. Attach the leg bases (04) to the bottom of the left and right desk legs using bolts (B) and the large Allen wrench (C).

Step 2: Attaching the Side Plates and the Transmission Rod

  1. Attach the side plates (05) to the top of the desk legs using bolts (A) and the large Allen wrench (C).
  2. Loosen the coupling nut on the transmission rod (06).
  3. Before attaching the transmission rod, measure the heights of the two desk legs to ensure they are level. If not, insert the transmission rod into the hole in the left leg. Turn the rod clockwise to lower the left leg or anti-clockwise to raise it until it's level with the right leg.

  4. NOTE: Make sure the set screw faces out.

    Ensure the transmission rod is properly inserted into the hole in the left leg. Smoothly connect the other end of the rod to the end of the motor drive shaft on the right leg.
  5. Secure the transmission rod to the motor drive shaft by turning the set screw clockwise using the small Allen wrench (D).
  6. Tighten the coupling nut to fine-tune the transmission rod fit.

Step 3: Assembling and Attaching the Desktop

  1. Assemble the desktop (07) by inserting wood dowel pins (G) into the pre-drilled holes and joining the two desktop halves.
  2. Attach the assembled desktop to the frame using screws (F). You can use a drill (with suitable torque and speed) or a Phillips screwdriver.
  3. Attach the controller (08) and storage hooks (H) to the underside of the desktop using screws (F).

Step 4: Connecting the Cables

  1. Connect the controller (08) cable to the corresponding port on the desk leg.
  2. Connect the AC adapter (09) to the desk leg and then to a power outlet.

Step 5: Installing the Cable Hole Covers

  1. Insert the cable hole covers (J) into the desktop's cable management holes.

Using the Controller

The desk controller features buttons for height adjustment and memory settings.

Settings

SettingInstructions
Change Display Height UnitsPress and hold the 'S' button until a flashing 'S-' is displayed. Press 'S' again, and 'Un' is displayed. Press 'S' to select it, press '▲' or '▼' to switch between 'IN' (imperial) and 'SI' (metric), and press 'S' to save your choice.
Change Collision Detection SensitivityLong press the 'S' button, 'S-' shows and flashes. Press 'S' again and the display shows 'Un.' Press '▲' or '▼' to switch to 'CF.' Press 'S' to select. Press '▲' or '▼' to switch between 'OFF,' 'Low (L),' 'Normal (n),' or 'Heavy (H)' collision force detection. Press 'S' to save your choice.
ResetPress and hold the '▼' button for 5 seconds, and the screen will show 'RES.' Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes

CodeDescription / Solution
HotOverheating Protection: When the motor has been working continuously for 2 minutes, it will stop operating to prevent damage from overheating. Wait for at least 18 minutes before making any further height adjustment.
E10Sensor Malfunction Warning: Motor safety sensor can't be detected. Power off, check the connection between the motor and controller, and power back on again.
E20Overloading Warning: Max load exceeded. If raising the desk, take items off the desk and try again. If lowering the desk, power off, take items off the desk, power back on, and try again.
E02Operation Status Warning: The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use.
E32Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E31Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E60Unequal Leg Height Warning: Power off the desk and check whether the left and right legs are at the same height. Adjust if necessary by following the instructions. Power on again.
— (No Code)Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected.

Technical Support

ErGear strives to provide quality products and service. For any issues, please contact ErGear technical support.

Models: EGESD6B, EGESD6V, EGESD6N, EGESD6B Height Adjustable Electric Standing Desk, Height Adjustable Electric Standing Desk, Adjustable Electric Standing Desk, Electric Standing Desk, Standing Desk

File Info : application/pdf, 14 Pages, 3.10MB

PDF preview unavailable. Download the PDF instead.

B12 XpXci9L

References

Adobe Illustrator 25.0 (Windows) iLovePDF

Related Documents

Preview ErGear Electric Standing Desk Instruction Manual
Comprehensive instruction manual for ErGear Electric Standing Desk models EGESD6B, EGESD6V, EGESD6N, EGESD7B, EGESD7V, EGESD7N. Includes detailed assembly steps, controller usage, height adjustment, and troubleshooting error codes for optimal desk operation.
Preview ErGear 55-inch Electric Standing Desk Instruction Manual
This instruction manual provides comprehensive assembly steps, specifications, and controller usage guidelines for the ErGear 55-inch Electric Standing Desk models EGESD6B-1 and EGESD6V-1. Learn how to set up your height-adjustable desk, operate its functions, and troubleshoot common issues.
Preview ErGear 55" Electric Standing Desk Instruction Manual EGESD6B-4 EGESD6V-4
Comprehensive instruction manual for the ErGear 55" Electric Standing Desk models EGESD6B-4 and EGESD6V-4. Includes detailed assembly steps, parts lists, controller usage, settings adjustment, and troubleshooting error codes for optimal desk operation and maintenance.
Preview ErGear 55" Electric Standing Desk Instruction Manual EGESD6B-3 EGESD6V-3
Comprehensive instruction manual for the ErGear 55" Electric Standing Desk (models EGESD6B-3, EGESD6V-3), covering assembly, operation of the electric controller, height adjustment, and troubleshooting common error codes. Learn how to set up and use your adjustable sit-stand desk efficiently.
Preview ErGear 55-inch Electric Standing Desk Instruction Manual EGESD6B-1 EGESD6V-1
This instruction manual provides comprehensive assembly, operation, and troubleshooting guidance for the ErGear 55-inch Electric Standing Desk models EGESD6B-1 and EGESD6V-1. Learn how to set up your adjustable height desk, use the controller for height adjustments and settings, and understand error codes for maintenance.
Preview ErGear Electric Standing Desk Instruction Manual - Assembly & Operation Guide
Comprehensive instruction manual for the ErGear Electric Standing Desk, covering assembly, specifications, parts list, and operational guide for models EGESD21, EGESD22, EGESD23, and EGESD24.
Preview ErGear Electric Standing Desk Instruction Manual - Assembly and Operation Guide
Comprehensive instruction manual for the ErGear Electric Standing Desk (Models EGESD8B, EGESD8V). Learn how to assemble, operate, and troubleshoot your height-adjustable desk.
Preview ErGear Electric Standing Desk Instruction Manual
Comprehensive instruction manual for the ErGear Electric Standing Desk, covering assembly, operation, and troubleshooting for models EGESD9B and EGESD9V.