BIGBIG WON BLITZ - User Manual

01. ESQUEMA DE PEÇAS

Diagram Description:

• Left Joystick
• D-pad
• Left light strip
• Channel light
• Turbo button
• Change button
• NFC
• FN key
• M4 button
• ZR button
• M2 button
• M3 button
• M1 button
• ZL button
• Screenshot button
• R button
• L button
• A/B/X/Y buttons
• Pairing button
• Right Joystick
• Right light strip
• Configuration button
• Macro Recording button
• HOME button (implied)
• Type-C port (implied)

Packing List:

• Xunlong wireless gamepad * 1
• Manual * 1
• Certificate * 1
• Data cable * 1

Supported Platforms:

• Switch
• Win10/11
• Android/iOS

02. LIGADO / DESLIGADO

Press and hold the [HOME button] for 3 seconds to turn the controller on/off.

03. CONEXÃO

This controller supports two connection methods: Bluetooth and wired connection.

Bluetooth Connection:

• After the controller is powered on, press and hold the [Pairing button] on the top for 3 seconds. The [HOME button] light flashes rapidly, indicating it has entered pairing mode.
• When the connection is successful, the [HOME button] light stays on. (The channel indicator light on Switch mode depends on which controller port the gamepad is connected to on the host.)

Wired Connection:

• After the controller is powered on, use the Type-C data cable to connect the controller to the host.

Note:

• This controller supports Switch and Xinput modes. After connecting to the host, you need to switch to the corresponding host mode for normal use. The default is Switch mode.
• Steam Platform: You need to check "Support XBOX configuration" in "Settings - Controller - General Controller Settings" of the Steam software, otherwise, it may cause issues where the controller is not recognized in the game.
• Switch Platform: After connecting to the Switch via wire, you need to enable "Settings - Controller and Sensors - Wired Controller Connection" on the Switch.

04. ALTERAÇÃO DE MODOS

This controller supports Switch and Xinput modes. After connection, you need to switch to the corresponding mode for normal use.

• Switch to Switch Mode: Press and hold the [A button] + [HOME button] for 3 seconds until the [HOME button] light turns red.
• Switch to Xinput Mode: Press and hold the [B button] + [HOME button] for 3 seconds until the [HOME button] light turns green.

Note: To connect to iOS and Android platforms via Bluetooth, you must switch to Xinput mode.

05. MAPEAMENTO

The controller comes with four expandable buttons and supports button mapping configurations.

• Set Mapping: Press [FN key] + [M1/M2/M3/M4 button]. The [FN indicator] breathes, indicating it has entered mapping state. Press the front button that needs to be mapped to M1/M2/M3/M4 again, and the [FN indicator] will flash twice, indicating successful mapping.
• Clear Single Mapping: Press and hold the button to be unmapped ([M1/M2/M3/M4]), then double-click the [FN key]. The [FN indicator] flashes twice, indicating the current key's mapping configuration has been cleared.
• Clear All Mappings: Double-click the [FN key] directly. The [FN indicator] flashes twice, indicating that all key mapping configurations have been cleared.

06. BURST

This controller supports button burst configuration. Supported buttons include A/B/X/Y, D-pad (↑↓/←→), L/R/ZL/ZR, M1/M2/M3/M4, a total of 16 buttons.

• Set Burst: Press and hold [FN key] + the button to be set. The [FN indicator] flashes twice, indicating successful initialization. (During burst operation, the [FN indicator] will flash at the current burst frequency.)
• Clear Single Burst: Press and hold the button to cancel burst, then double-click the [FN key]. The [FN indicator] flashes twice, indicating the current button's burst configuration has been cleared.
• Clear All Bursts: Double-click the [FN key] directly. The [FN indicator] flashes twice, indicating that all button burst configurations have been cleared.
• Burst Frequency: Press and hold [FN key] + [Right arrow button] to switch between 5/s, 10/s, 20/s three frequencies. The default is 5/s.

07. GRAVAÇÃO DE MACRO

This controller supports the macro recording function. Each macro must be linked with a return key (M1/M2/M3/M4) as a trigger key. Keys that support recording are A/B/X/Y, D-pad (↑↓/←→), L/R/ZL/ZR, LS/RS, eight-direction control.

• Record Macro: Press and hold [FN key] + [M1/M2/M3/M4 button] for 3 seconds. The [FN indicator] breathes, indicating it has entered macro recording state. Press the controller buttons to record the macro. After recording is complete, click the [FN key]. The [FN indicator] flashes twice, indicating recording has finished. (While the macro is running, the [FN indicator] will flash slowly until the macro is executed.)
• Clear Single Macro: Press and hold the key to cancel the macro ([M1/M2/M3/M4]), then double-click the [FN key]. The [FN indicator] flashes twice, indicating the current key's macro configuration has been cleared.
• Clear All Macros: Double-click the [FN key] directly. The [FN indicator] flashes twice, indicating that all key macro configurations have been cleared.

08. ALTERAÇÃO DE CONFIGURAÇÃO INTEGRADA

Switch Mode: First, click the [HOME button] to change the channel indicator from red to white, signifying entry into configuration change mode. The four indicators in this mode represent four different built-in configurations.

• Click the [HOME button] to start switching configurations. The indicators will cycle from top to bottom. The first indicator being lit represents the current set of integrated configurations.
• If there is no configuration change behavior within 5 seconds, it will automatically exit configuration change mode, the indicator will change from white to red, and the channel will be re-indicated.

Xinput Mode: There is no channel indication function in this mode, so the indicator light is white by default, indicating the current board configuration. In this mode, click the [HOME button] to switch configurations directly.

09. ALTERAÇÃO DE ZONA MORTA DO CONTROLE

This controller is positioned as a competitive controller, so a dead zone of 0 is selected in the factory default setting. This allows for greater control precision but may result in slight drift in games without dead zones. To cater to more user groups, two dead zones (0/10) are provided for users to choose from.

• Operation: Hold [FN key] + the left and right joysticks ([Left joystick]/[Right joystick]) down simultaneously to switch between 0/10 for the dead zone of the left and right joysticks, respectively.

10. CALIBRAÇÃO DE JOYSTICK

When there is severe joystick deviation and it is not pushed to its maximum value, try calibrating the joystick by following these steps:

1. Hold the [Plus button] + [Minus button] simultaneously for 3 seconds. The left and right light strips breathe orange simultaneously, indicating entry into calibration mode.
2. Push the joystick to its limit and rotate it in a uniform circle, repeat 3-5 times.
3. Finally, press the [Plus button] and [Minus button] simultaneously. The left and right light strips will flash twice and then exit, indicating that calibration is finished.

11. CALIBRAÇÃO DE GIROSCÓPIO

When the gyroscope in the gamepad is deviated, try calibrating the gyroscope by following these steps:

1. Place the gamepad on a horizontal table and press the [Plus button] + [Screenshot button] simultaneously. The left and right light strips breathe purple simultaneously, indicating entry into calibration mode.
2. Wait a few moments for the left and right light strips to flash twice in purple, then calibration is finished.

12. AJUSTE DE VIBRAÇÃO

The controller supports four-speed vibration adjustment, and the operation methods are as follows:

• Press [FN key] + [Right arrow button]. The trigger motor vibration can be cycled through four speeds: strong, medium, weak, and off.

13. DESCRIÇÃO DA BATERIA

Low Battery: When the battery is low, the light strip on both sides of the gamepad flashes red 10 times at a rate of 2 times per second, alerting you every five minutes.

Charging: When connected to the power supply, the gamepad's light strip breathes red, indicating it is in a charging state. When the battery is fully charged, the charging light effect turns off, and the light strip returns to its original state.

Charging Dock: The dock has no light indication in standby mode. When the gamepad is connected to the dock, if the dock's RGB indicator is flashing in seven colors, it indicates the gamepad is charging. If the dock's RGB is always green, it indicates the gamepad's battery is fully charged.

14. INSTRUÇÕES DETALHADAS DE OPERAÇÃO FUNCIONAL

Please visit the official website for video tutorials: Mo Jiang official website support page

https://www.bigbigwon.com/support

15. SEUS DIREITOS

Limited warranty of 12 months from the date of purchase.

Get video tutorials with QR code.

We are here to support and serve you with Bigbigwon products: video tutorials, update tools, e-manuals.

www.bigbigwon.com/support

BIGBIG WON SUPPORT