Wampat W15A1184B Assembly Instructions

Model: W15A1184B

Introduction

Thank you for choosing Wampat products. Please read the instructions carefully before installation and keep them properly.

Tips:

Do not attempt to move this furniture without first removing all equipment.
Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip over onto the child.
Please contact us using the details shown for further advice.

Warning: If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts!

What's in the Box ?

Diagram shows all included parts laid out and labeled with numbers and letters.

Identifier	Description	Quantity
A	Cam bolt	28
B	Cam lock	36
C	Wooden dowel	28
D	Cam bolt	4
E	Left support rod	1
F	Screw	32
G	Crash pad	4
H	Right support rod	1
I	Screw	8
J	Wire cap	2
K	Hinge	4
L	Screw	12
M	Horizontal bubble	1
N	Hexagon socket key	1
O	Shelf support pin	4
P	L-iron	4
Q	Cover	18
S1	Cabinet hanger
S2
S3
S4	Anchor and screw	4
S5	Anchor and screw	4

Tools Required (Not included): Stud Finder ✏️, Pencil ✏️, Level ?, Drill ?️, Wood Drill ?️, Screw driver ?️, Hammer ?.

Installation Steps

Step 1a: Wood Stud Wall Mounting

Fit for: 406mm (16"), 610 mm (24 ") stud.

Tools Required: Stud Finder ✏️, Pencil ✏️, Level ?, Drill ?️, Screw driver ?️.

Diagram shows a wall with studs. Use a level (F) to mark the exact location of mounting holes. Then, drill pilot holes (∅4mm / 5/32").

Step 2: Screw the mounting screws (S5) onto the wall. Ensure they are securely fastened.

Warning: Make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended. Installers are responsible to provide hardware for other types of mounting situations. Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

Step 1b: Solid Brick and Concrete Mounting

Tools Required: Pencil ✏️, Drill ?️, Wood Drill ?️, Hammer ?, Screw driver ?️.

Diagram shows a brick wall. Mark the exact location of mounting holes. Then, drill pilot holes (∅11mm / 7/16").

Step 4: Secure wall anchors (S4) and screws (S5). Screw S5 onto S4 into the drilled holes in the wall with a hammer.

Warning: Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

Step 5: Attach Wall Hanging Accessories

Tips: Please disassemble the wall hanging accessories before hanging the product on the wall. To make sure you can use this product properly!!

Diagram shows how to attach wall hanging accessories (S1, S2, S3) to the main unit.

Step 6: Prepare Panels

Insert dowels (C) into panels (1,4). Insert cam locks (B) into panel (1). Then, insert parts (D) into panel (1). Rotate the cam locks (B) 90° ? to secure the parts (D).

Parts Used: B x 4, C x 8, D x 4.

Step 7: Assemble Main Frame (Part 1)

2 Person Task ?. Attach panels (2,3) to panel (1) correctly. Insert and secure cam locks (B) to panels (2,3) to lock them.

Parts Used: B x 4.

Step 8: Insert Cam Bolts

Screw cam bolts (A) into panels (1,2,3,4,5,6).

Parts Used: A x 24.

Step 9: Assemble Main Frame (Part 2)

Insert dowels (C) into panels (7,8,9). Attach panels (7,8,9) to panels (1,2,3) correctly. Insert and secure cam locks (B) to panels (7,8,9) to lock them.

Parts Used: B x 12, C x 10.

Step 10: Attach Shelves

Attach panels (10) to panels (1,2,3) correctly. Insert and secure cam locks (B) to panels (10) to lock them. Note the orientation based on L1 < L2.

Parts Used: B x 6.

Step 11: Attach Wire Cap

Insert dowels (C) into panels (5,6). Attach panels (5,6) to panel (4) correctly. Attach part (J) (wire cap) to panel (4).

Parts Used: J x 1.

Step 12: Assemble Main Frame (Part 3)

2 Person Task ?. Insert dowels (C) into panels (7,8,9). Insert and secure cam locks (B) to panels (10) to lock them. Attach panels (4,5,6) to panels (7,8,9) with screws (L).

Parts Used: B x 6, L x 12, C x 10.

Step 13: Attach Hinges

Attach parts (K) (hinges) to panel (11) with screws (F) correctly.

Parts Used: K x 4, F x 8.

Step 14: Attach Side Panels and Wire Cap

Attach parts (11) to panels (5,6) with screws (F) correctly. Insert parts (G) (crash pads) into panels (11). Attach part (J) (wire cap) to panel (1).

Parts Used: G x 4, J x 1, F x 16.

Step 15: Attach Support Rods

Attach parts (E,H) (support rods) to panels (8,9,11) with screws (I) correctly.

Parts Used: E x 1, H x 1, I x 8.

Step 16: Hang Cabinet on Wall

2 Person Task ?. With help from another person, carefully hang the assembled cabinet onto the wall screws (S5).

Step 17: Secure Cabinet to Wall

2 Person Task ?. Secure parts (S2) onto the screws (S5), then screws and tighten screws (S5). Part (S2) must be installed correctly to ensure safe use.

Parts Used: S2 x 4, S3 x 4.

Step 18: Final Cabinet Hanger Attachment

Secure parts (S1) onto the parts (S3).

Parts Used: S1 x 4.

Step 19: Hinge Adjustments

Diagrams show hinge adjustments: Adjust Height / 高さを調節, Adjust front and back / 前後を調節, Adjust Left and right 左右を調節. Each adjustment is illustrated with a close-up of the hinge mechanism and an arrow indicating the direction of movement.

Option A: Floating TV Stand

Step 20: Floating TV Stand Assembly Complete

The floating TV stand is now assembled.

Step 21: Attach Panel 12

Attach panel (12) to panels (8,9) using parts (O) (shelf support pins).

Parts Used: O x 4.

Step 22: Apply Stickers

Stick stickers (Q) on cam locks (B) and the holes for a finished look.

Parts Used: Q x 18.

Option B: Fireplace

Step 23: Fireplace Unit Ready

The unit is ready for the fireplace option.

Step 24: Prepare Fireplace Unit

Before attaching the fireplace to the TV stand, unscrew four silver screws on both sides of the fireplace unit.

Step 25: Handle Fireplace Glass

Carefully remove the front glass from the fireplace unit and place it on a soft and clean surface.

Step 26: Prepare Main Unit for Fireplace

Screw cam bolts (A) into panels (8,9) of the main unit.

Parts Used: A x 4.

Step 27: Attach Fireplace Mounting Brackets

Attach parts (P) (L-irons) to panels (13,14) with screws (F) correctly. Attach panels (13,14) to panels (8,9). Insert and secure cam locks (B) to panels (13,14) to lock it.

Parts Used: B x 4, F x 4, P x 4.

Step 28: Attach Additional Brackets

Attach parts (P) (L-irons) to panels (1,4) with screws (F) correctly.

Parts Used: F x 4.

Step 29: Insert Fireplace Unit

2 Person Task ?. Insert fireplace (15) from the front of the unit correctly.

Step 30: Secure Fireplace Unit

Attach fireplace (15) to panels (13,14) with screws (R) correctly.

Parts Used: R x 4.

Step 31: Reattach Glass Front

Attach the glass front back to the fireplace.

Step 32: Final Fireplace Assembly Stickers