Manuals+

RainPoint ITV205 User Manual

More Than Water Saving

Warm Tips - Please Read Before Using

Product Overview at a Glance

The RainPoint ITV205 is a two-zone water timer that allows you to water two different areas from the same faucet. Each zone can be programmed with an independent start time, duration, and frequency.

Key Components:

Dial Positions and Functions:

Dial Position Function
SET CLOCK Switch 12H/24H and set the current time.
START TIME Set the first irrigation start time for each zone.
HOW LONG Determine how long to water for each zone.
HOW OFTEN Choose how often you will water for each zone.
ON Timer waters according to your customized schedule for both zones.
OFF Turn off all watering.

Specification

Specification Details
Working Water Pressure 0.5bar-8bar (7 psi-116 psi)
Max Flow Rate 10 Gal/Min (35L/Min)
Waterproof Level IP54
Working Temperature 37.4°F-122°F (3°C-50°C)
Working Voltage DC 2.3V~DC 3.3V
Watering Frequency Every 1-12 hours or Every 1-7 days
Watering Duration From 1 minute to 3 hours 59 minutes (4 hours)
Water Inlet NH (US) for 3/4" taps; BSP (EU) for 3/4" or 1" taps
Water Outlet For 3/4" standard garden hose
Time Format 12H or 24H
Power By 2 AAA alkaline batteries (Not included)

Product Installation

Installing the Batteries

  1. Remove the battery compartment cover on the back of the timer.
  2. Insert 2 new AAA (1.5V) alkaline batteries (not included).
  3. Put the battery compartment cover back on the timer and press firmly to make sure it is completely sealed.

Note:

Installing the Timer

  1. Turn off the garden faucet.
  2. Wrap Teflon Tape around the faucet threads.
  3. Screw the timer to the garden faucet, ensuring the display is as vertical as possible to the ground to prevent rainwater accumulation and leakage into the interior.
  4. Wrap Teflon Tape around the threads of the timer outlets.
  5. Screw the garden hoses to the timer outlets.
  6. Turn on the faucet after programming the timer.

Tips: If the connection between the timer and the faucet or hose is not tight or leaking, wrap more Teflon Tape (thread seal tape) to make them tight.

Please do not use tools; install the timer by hand. When expecting freezing temperatures, timers should be removed from the hose faucet and stored indoors to avoid potential freeze damage.

Please install the filter properly and keep it clean as follows: [Filter installation diagram with checkmark for correct installation and cross for incorrect]

Activate the Timer Before Use

Please activate the device before using it for the first time or after a period of inactivity.

  1. Keep the garden faucet turned off.
  2. Turn the timer dial to "ON".
  3. Press and hold the "MANUAL" button for 3-5 seconds to enter Manual Watering Mode.
  4. Press the "ZONE" button twice to select both Zone 1 and Zone 2. When the screen flashes, immediately press the "OK" button to run manual watering.
  5. After hearing 2 "click" sounds or waiting for about 5 seconds, the valves in the timer are opened. Turn the dial to "OFF" to close the valves.
  6. Repeat steps 2-5 for 3-5 times.
  7. Test: Turn on the faucet a little bit, and then repeat steps 2-5 to check if the water flow is as expected or shuts off correctly.

If the test is successful, the timer valves are normal. Use with confidence! If not, repeat steps 2-5 several times or contact RAINPOINT support immediately.

Note: When testing, keep away from the water timer outlet to avoid being splashed and wet.

Programming the Timer

Step 0: Understanding Zones

This is a two-zone timer allowing you to water two different areas from the same faucet. Each zone can be programmed with an independent start time, duration, and frequency.

Note: Dual zones operating simultaneously have lower water pressure than a single zone because the water pressure is divided between the two zones.

Design the program separately for each ZONE:

  1. First, set up ZONE 1 following steps 1-4 below. Then turn the dial to "ON" to save the changes.
  2. Press the "ZONE" button to select ZONE 2, and follow steps 2-4 to set up. Turn the dial to "ON" to save all the plans.

Step 1: Set Clock

Follow these steps to set the current time:

  1. Turn the dial to "SET CLOCK". Use "+" or "-" buttons to select 24-hour or 12-hour format and press "OK" to confirm.
  2. Use "+" or "-" buttons to set the current exact time. If using the 12-hour format, note the AM and PM.
  3. Use the "OK" button to confirm and switch between hours or minutes.
  4. Turn the dial clockwise to save the changes in this STEP and proceed to the next STEP.

TIPS: After setting, turn the dial to save changes instead of pressing the "OK" button. Pressing "OK" after setting will return to the previous setting.

Step 2: Start Time

Set the desired start time for watering:

  1. Turn the dial to "START TIME".
  2. Use "+" and "-" buttons to set your start time.
  3. Use the "OK" button to switch between Hours or Minutes.
  4. Turn the dial clockwise to save the changes in this STEP and proceed to the next STEP.

TIPS: After setting, turn the dial to save changes instead of pressing the "OK" button. Pressing "OK" after setting will return to the previous setting.

Step 3: How Long

Set the watering duration:

  1. Turn the dial to "HOW LONG".
  2. Use "+" and "-" buttons to select watering duration, from 1 minute to 3 hours 59 minutes.
  3. Use the "OK" button to switch between Hours or Minutes.
  4. Turn the dial clockwise to save the changes in this STEP and proceed to the next STEP.

TIPS: After setting, turn the dial to save changes instead of pressing the "OK" button. Pressing "OK" after setting will return to the previous setting.

Step 4: How Often

Set the watering frequency:

  1. Turn the dial to "HOW OFTEN".
  2. Use "+" and "-" buttons to set your watering frequency. You can choose to water every 1 to 12 hours, or every 1 to 7 days. (NOTE: 1 = every day, 2 = every other day, etc.)
  3. Turn the dial clockwise to save the changes in this STEP and proceed to the next STEP.

Examples of watering frequency:

EVERY 1 DAY: [Diagram showing watering schedule for each day of the week]

EVERY 2 DAYS: [Diagram showing watering schedule for every two days]

EVERY 3 DAYS: [Diagram showing watering schedule for every three days]

Step 5: Automatic Watering

Once programmed, the timer will water automatically:

  1. Turn the dial to "ON".
  2. The LCD screen will display the current time and the next watering start time for Zone 1, then the current time and the next watering start time for Zone 2.

CONGRATULATIONS! Your timer has now been programmed successfully! It will automatically start watering based on the programmed start time, duration, and frequency. You can now keep the faucet open and trust the timer to water!

Additional Functions

Rain Delay Mode

Rain delay allows you to postpone watering on both zones for a set period of time without interrupting your set watering schedule. To access rain delay, follow these steps:

  1. When the dial is in the "ON" position, press and hold the "DELAY" button for 3-5 seconds to enter the delay mode.
  2. In Delay Mode, "24H" will flash on the screen. Press "+" and "-" to select the delay period (24H, 48H, or 72H).
  3. Press the "OK" button to run the delay function. The screen will show a countdown of the remaining delay.
  4. To cancel rain delay, hold the "DELAY" button for 3-5 seconds again to resume your programmed watering schedule.

Note: Remember to press the "OK" button after selecting the rain delay time to start the program. Otherwise, the setting will automatically exit after the screen flashes for 3-5 seconds.

Manual/Hand Watering

This function allows you to manually water without interrupting your set watering schedule. Follow these steps:

  1. Turn the dial to "ON".
  2. Press and hold the "MANUAL" button for 3-5 seconds to enter Manual Watering Mode.
  3. Press the "ZONE" button to select the zone you want to use (Zone 1 only, Zone 2 only, or Zone 1 and Zone 2).
  4. Use the "+" or "-" button to adjust the manual watering time from 1 minute to 8 hours. The default watering time is 10 minutes. Press and hold the "+" or "-" button to quickly increase or decrease the time.
  5. Press the "OK" button immediately when the screen flashes to confirm and start manual watering. The screen will show a pattern and the remaining time for manual watering.
  6. To stop manual watering, hold the "MANUAL" button for 3-5 seconds to exit manual watering mode and restore the original watering program. Alternatively, turn the dial to "OFF" to stop manual watering, then turn the dial back to "ON" to restore the original program.

NOTE: Remember to press the "OK" button after setting the manual watering time to start manual watering. Otherwise, the setting will automatically exit after the screen flashes for 3-5 seconds.

Use Only One of the Zones

To use only ZONE 1 and close ZONE 2:

  1. Turn the dial to "START TIME" and press "ZONE" to select ZONE 2.
  2. Press the "+" or "-" button to adjust the Hour until the screen displays "OFF".
  3. Turn the dial to "ON" to save the changes. This means ZONE 2 is off, and you can program ZONE 1 as needed. The timer will then only run ZONE 1.

If you want to use only ZONE 2 and close ZONE 1, the same applies.

Off Mode

  1. If you wish to stop all watering plans for an extended period, turn the dial to "OFF". Your settings are saved.
  2. The timer will not water automatically in OFF mode. The screen will display the word "OFF" in large letters.
  3. To start automatic watering again, turn the dial back to "ON" to resume your programmed watering schedule.

Battery Status

Battery status will be displayed as follows:

Note: When the low battery indicator appears, the valve will close automatically to avoid leakage. Please replace the battery to recover.

Troubleshooting

Issue Possible Cause Advice
The water inlet leakage 1. No filter or filter not placed horizontally.
2. The faucet is not the correct 3/4" standard.		 1. Add filter and ensure it is placed horizontally in the inlet.
2. Make sure the faucet is a 3/4" faucet.
3. Strengthen with Seal tape.
The water doesn't stop/flow out 1. Long-term storage and transportation made the valve inactive.
2. Valve blockage.		 1. Keep the tap turned off and turn the timer dial to ON.
2. Select the zone to fix (ZONE 1 or ZONE 2) and run manual watering for 3-5s, then stop it.
3. Repeat step 2 for 5 to 7 times.
4. Try using it normally.
Dial or button problems 1. The dial/valve is stuck.
2. Accidentally holding the OK button while inserting batteries.		 1. Same procedure as above.
2. Turn the dial to OFF to check if the valve can be closed.
Short battery life 1. Mixed use of old and new batteries.
2. Used carbon batteries or rechargeable batteries.		 1. Use brand new alkaline batteries.
2. Rechargeable and carbon batteries have short and unstable battery life; use alkaline batteries instead.
Low water pressure 1. Filter blockage.
2. Inlet pressure not sufficient to support watering.		 1. Check if the filter is clogged; clean or replace it.
2. Ensure the timer is installed properly and not cross-threaded.
3. Install a booster pump or other auxiliary equipment to increase pressure.
The timer does not water 1. The dial is turned to OFF position.
2. The faucet is not turned on.
3. The battery is dead, it shuts down automatically.
4. Rain delay is ON.		 1. Rotate the dial to ON position.
2. After finishing all settings, turn on the faucet.
3. Replace with new alkaline batteries.
4. Wait for the plan to resume.
LCD display became blank 1. The LCD temporarily does not display under long-term exposure.
2. The battery is dead, it shuts down automatically.		 1. Avoid long-term exposure under sunlight.
2. Replace with new alkaline batteries.

Cleaning Your Timer

After a period of use, impurities or dirt in the water may accumulate in the timer. Clean the timer regularly to ensure proper operation.

Follow these steps:

  1. Turn off the garden faucet and remove the timer. Check the filter at the water inlet for accumulated impurities.
  2. If the filter is dirty, take it out and rinse it with running water. [Diagram of filter removal and rinsing]
  3. Turn on the Manual Watering Mode to open the valve and check if the timer's water pipe is blocked. If blocked, clean gently with a small cleaning brush. [Diagram of cleaning the timer's internal components]

Warnings

  1. For outdoor use only. Placing the timer in sheltered outdoors will prolong its lifetime.
  2. To avoid damage, tighten without using tools.
  3. The filter should be placed horizontally in the water inlet to prevent leakage.
  4. When low power, replace batteries to avoid interruption of normal operation. Ensure the battery tray is dry when replacing batteries.
  5. When the timer is not in use, remove the batteries and store indoors.
  6. Do not use the timer above 120°F (50°C) or below 38°F (3°C).
  7. Do not subject the product to extreme force and shock.
  8. Severe electrical shock could result if water sprays into outlets or sources of electrical current. Never immerse the product in water.

This product is MADE IN CHINA and conforms to the national standards of the United States, Britain, Germany, and France. Use this product correctly. If discarding, dispose of it according to national requirements. Protect the environment.

[Recycling symbols and instructions in French]

EC REP
NAME: VIAJE ELECTRONIC COMPANY LIMITED
ADDRESS: E588, 13 ADELAIDE ROAD, DUBLIN, D02 P950, IRELAND
Email: VIAJEELE@outlook.com

[CE marking, battery symbols, Made in China]

Warranty

RainPoint provides a 1-year warranty against manufacturing defects in materials and workmanship from the date of purchase. During the warranty period, RainPoint will replace defective products free of charge under reasonable use and service.

To place a warranty request, email service@rainpointus.com with your order ID. A response will be provided within 24 hours.

Customer Service

For setup assistance, search for "RainPoint" on YouTube for installation videos!

If the user manual does not provide the information you need, please contact RainPoint before returning the product to the store and provide the LOT NO. of your device.

Email: service@rainpointus.com

WhatsApp: +1 626-780-5952

US Free Hotline (English): +1 833-381-5659 (MON-FRI 9:30 AM-5:30 PM PST)

UK Free Hotline (English Deutsch): +44 800-808-5337 (MON-FRI 9:00 AM–5:00 PM CET)

Consejos de Seguridad (Safety Tips in Spanish)

If you have any problems during use, please contact support:

Vista del Producto (Product View in Spanish)

En una Mirada (At a Glance)

Dial: Rotate the dial to personalize your watering schedule; Save the changes (settings).

Botón de Cambio de Zona (Zone Switch Button): Switch between Zone 1 and Zone 2.

Botón OK / Manual: Confirm to go to the previous/next step or manual watering mode.

DELAY / + Button: Adjust the time and system setup or delay watering program.

Botón - / +: Adjust the time and system setup.

Dial Positions and Functions (Spanish):

Posición del Dial Función
SET CLOCK Switch between 12H/24H and configure the current time.
START TIME Configure the start time of the first irrigation for each zone.
HOW LONG Determine the watering duration for each zone.
HOW OFTEN Choose the frequency with which you will water each zone.
ON The timer waters according to your personalized schedule for each Zone.
OFF Turn off all watering.

Especificaciónes (Specifications in Spanish)

Specification Details
Presión de Agua de Trabajo (Working Water Pressure) 0.5bar-8bar (7 psi-116 psi)
Caudal Máximo (Max Flow Rate) 10 Gal/Min (35L/Min)
Nivel de Impermeabilidad (Waterproof Level) IP54
Temperatura de Trabajo (Working Temperature) 37.4°F-122°F (3°C-50°C)
Tensión de Trabajo (Working Voltage) DC 2.3V~DC 3.3V
Frecuencia de Riego (Watering Frequency) Every 1-12 hours or Every 1-7 days
Watering Duration From 1 minute to 3 hours 59 minutes (4 hours)
Entrada de agua (Water Inlet) NH (US) for 3/4" taps; BSP (EU) for 3/4" or 1" taps
Salida de Agua (Water Outlet) For 3/4" standard garden hose
Formato de Hora (Time Format) 12H or 24H
Alimentado Por (Power By) 2 AAA Alkaline Batteries (Not included)

Instalación del Producto (Product Installation in Spanish)

Instalando las Baterías (Installing the Batteries)

  1. Remove the battery compartment cover on the back of the timer.
  2. Insert 2 new AAA (1.5V) alkaline batteries (not included).
  3. Place the battery compartment cover back on the timer and press firmly to ensure it is completely sealed.

Note: Restore the battery compartment cover firmly to ensure water resistance. When the timer is not used for a prolonged period, please remove the batteries and dispose of them properly. Replace batteries when the low battery indicator ? appears on the screen. Do not throw batteries into fire. Batteries can explode or leak. For a longer lifespan, please use 2 new AAA alkaline batteries (not included). Do not mix new and old alkaline, standard (carbon-zinc), or rechargeable batteries.

Instalando el Temporizador (Installing the Timer)

  1. Close the garden faucet.
  2. Wrap Teflon Tape around the faucet threads.
  3. Screw the timer onto the garden faucet, ensuring the display is as vertical as possible to the ground to prevent rainwater from accumulating and filtering into the interior.
  4. Wrap Teflon Tape around the threads of the timer outlets.
  5. Connect the garden hoses to the timer outlets.
  6. Open the faucet after programming the timer.

Tips: If the connection between the timer and the faucet or hose is not tight or has leaks, wrap more Teflon Tape (thread seal tape) to ensure they are tight.

Please install the filter adequately and keep it clean as follows: [Diagram of filter installation]

Active el Temporizador Antes de Usar (Activate the Timer Before Use)

Please activate the device before using it for the first time or after a period of inactivity.

  1. Keep the garden faucet closed.
  2. Turn the timer dial to "ON".
  3. Press and hold the "MANUAL" button for 3-5 seconds to enter Manual Watering mode.
  4. Press the "ZONE" button twice to select both Zone 1 and Zone 2. When the screen flashes, immediately press the "OK" button to perform manual watering.
  5. After hearing 2 "click" sounds or waiting for about 5 seconds, the valves in the timer open. Turn the dial to "OFF" to close the valves.
  6. Repeat steps 2-5 for 3-5 times.
  7. Test: Open the faucet slightly, and then repeat steps 2-5 to check if the water flows or closes as expected.

If so, the timer valves are functioning normally, please use with confidence! If not, please repeat steps 2-5 several times or contact the RAINPOINT support team immediately.

Note: When performing the test, please keep away from the timer's water outlet to avoid splashing and getting wet.

Programando el Temporizador (Programming the Timer)

Paso 0: Comprendiendo las Zonas (Understanding the Zones)

This is a two-zone timer that allows you to water two different areas from the same faucet. Each zone can be programmed with a different start time, duration, and frequency.

Note: Simultaneous operation of both zones produces lower water pressure than when operating in a single zone because water pressure is divided between the two zones.

Please design the program separately for each ZONE:

  1. First, keep ZONE 1 and complete the configuration, following steps 1-4. Then turn the dial to "ON" to save the changes.
  2. Press the "ZONE" button to select Zone 2, and follow steps 2-4 to configure. Turn the dial to "ON" to save the changes.

Paso 1: Ajuste del Reloj (Set Clock)

  1. Turn the dial to "SET CLOCK". Use the "+" or "-" buttons to select the 24-hour or 12-hour format and press the "OK" button to confirm.
  2. Use the "+" or "-" button to set the exact time. If you choose the 12-hour format, please note the AM and PM.
  3. Use the "OK" button to confirm and switch between hours or minutes.
  4. Turn the dial clockwise to save the changes in this STEP and proceed to the next STEP.

TIPS: After completing this configuration, please turn the dial to save the changes instead of pressing the "OK" button. If you press the "OK" button after configuring, it will return to the previous configuration instead of saving it.

Paso 2: Hora de Inicio (Start Time)

  1. Turn the dial to "START TIME".
  2. Use the "+" and "-" buttons to set the start time.
  3. Use the "OK" button to change the time (Hours or Minutes).
  4. Turn the dial clockwise to save the changes in this STEP and proceed to the next STEP.

TIPS: After completing the configuration of this STEP, please turn the dial to save the changes instead of pressing the "OK" button. If you press the "OK" button after configuring, it will return to the previous configuration instead of saving it.

Paso 3: Duración (Duration)

  1. Turn the dial to "HOW LONG".
  2. Use the "+" and "-" buttons to select the watering duration, from 1 minute to 3 hours 59 minutes.
  3. Use the "OK" button to change to (Hours or Minutes).
  4. Turn the dial clockwise to save the changes in this STEP and proceed to the next STEP.

TIPS: After completing the configuration of this STEP, please turn the dial to save the changes instead of pressing the "OK" button. If you press the "OK" button after configuring, it will return to the previous configuration instead of saving it.

Paso 4: Frecuencia (Frequency)

  1. Turn the dial to "HOW OFTEN".
  2. Use the "+" and "-" buttons to set the watering frequency. You can choose to water every 1 to 12 hours, or every 1 to 7 days. (NOTE: 1 is every day, 2 is every other day, etc.)
  3. In this STEP, turn the dial clockwise to proceed to the next STEP.

TIPS: After completing the configuration of this STEP, please turn the dial to save the changes instead of pressing the "OK" button. If you press the "OK" button after configuring, it will return to the previous configuration instead of saving it.

Examples of watering frequency every day, every 2 days, and every 3 days:

CADA 1 DÍA (EVERY 1 DAY): [Diagram showing watering schedule for each day of the week]

CADA 2 DÍA (EVERY 2 DAYS): [Diagram showing watering schedule for every two days]

CADA 3 DÍA (EVERY 3 DAYS): [Diagram showing watering schedule for every three days]

Paso 5: Riego Automático (Automatic Watering)

  1. Turn the dial to "ON".
  2. The LCD screen will display the current time and the next watering start time in Zone 1, and then display the current time and the next watering start time in Zone 2.

ENHORABUENA! (CONGRATULATIONS!) Your timer has now been programmed successfully! Irrigation will start automatically based on the programmed start time, duration, and frequency. You can now keep the faucet open and trust the water timer!

Funciones Adicionales (Additional Functions)

Modo Retraso por Lluvia (Rain Delay Mode)

Rain delay allows you to postpone watering in both zones for a set period of time without interrupting the configured watering program. To access rain delay, follow the steps below.

  1. When the dial is in the "ON" position, press and hold the "DELAY" button for 3-5 seconds to enter the delay mode.
  2. In Delay Mode, you will find the "24H" option flashing on the screen. Press "+" and "-" to select the delay period of 24H, 48H, and 72H.
  3. Press the "OK" button to execute the delay function, then the screen will show a countdown of the remaining delay.
  4. To cancel rain delay, press the "DELAY" button for 3-5 seconds again to resume your programmed watering schedule.

Note: Please remember to press the "OK" button after selecting the rain delay time to start the rain delay program. Otherwise, the device will automatically exit the rain delay configuration after the screen flashes for 3-5 seconds.

Riego Manual/A Mano (Manual/Hand Watering)

This function allows you to manually water without interrupting your set watering schedule. To access this function, follow the steps below.

  1. Turn the dial to "ON".
  2. Press and hold the "MANUAL" button for 3-5 seconds to enter Manual Watering Mode.
  3. Press the "ZONE" button to select the zone you want to water (Solo Zona 1, Solo Zona 2, Zona 1 y Zona 2).
  4. Use the "+" or "-" button to adjust the manual watering time from 1 minute to 8 hours. The default watering time is 10 minutes. Press and hold the "+" or "-" button to quickly increase or decrease the time.
  5. Press the "OK" button immediately when the screen flashes to confirm and start manual watering. The screen will show the pattern and the remaining time for manual watering.
  6. To stop manual watering, hold the "MANUAL" button for 3-5 seconds to exit manual watering mode and restore the original watering program. (Or turn the dial to "OFF" to stop manual watering, and then turn the dial to "ON" again to restore the original watering program.)

NOTE: Please remember to press the "OK" button after configuring the time to start manual watering. Otherwise, the device will automatically exit the manual watering configuration after the screen flashes for 3-5 seconds.

Uso de una Sola Zona (Using Only One Zone)

If you want to use only ZONE 1 and close ZONE 2, please configure as follows:

  1. Turn the dial to "START TIME" and press "ZONE" to select ZONE 2.
  2. Press the "+" or "-" button to adjust the Hour until the screen displays "OFF".
  3. Turn the dial to "ON" to save the changes. This means ZONE 2 is off, and you can select ZONE 1 to program the schedule as needed, and the timer will function only in ZONE 1.

If you only want to use ZONE 2 and close ZONE 1, the same applies.

Modo OFF (OFF Mode)

  1. If you wish to stop all watering plans for a prolonged period, turn the dial to "OFF". (Your settings are saved)
  2. The timer will not activate automatically when in OFF mode. (The screen will display the word OFF in large letters)
  3. To start automatic watering again, turn the dial back to "ON" to resume your programmed watering schedule.

Estado de la Batería (Battery Status)

The battery status will be displayed as follows:

Note: When the low battery indicator appears, the valve will automatically close to prevent leaks. Please replace the battery to resume valve operation.

Resolución de Problemas (Troubleshooting)

Problema (Issue) Posible Causa (Possible Cause) Consejo (Advice)
Fuga en la entrada de agua (Water inlet leakage) 1. No filter or filter not placed horizontally.
2. The faucet is not the correct 3/4" standard.		 1. Add filter and ensure it is placed horizontally in the inlet.
2. Make sure the faucet is a 3/4" faucet.
3. Strengthen with Seal tape.
El agua no se detiene / se desborda (Water doesn't stop/overflow) 1. Long-term storage and transportation made the valve inactive.
2. Valve blockage.		 1. Keep the tap turned off and turn the timer dial to ON;
2. Select the zone to repair (ZONE 1 or ZONE 2) and execute manual watering for 3-5s and stop it;
3. Repeat Step 2 for 5 to 7 times;
4. Try using it normally.
Problemas con el Dial o los botones (Dial or button problems) 1. The dial/valve is stuck.
2. Accidentally pressed the OK button while inserting batteries.		 1. The same procedure as above.
2. Turn the dial to OFF to check if the valve closes.
Corta duración de las baterías (Short battery life) 1. Mixed use of old and new batteries.
2. Used carbon batteries or rechargeable batteries.		 1. Use brand new alkaline batteries.
2. Rechargeable and carbon batteries have a short and unstable battery life; please use alkaline batteries.
Baja presión de agua (Low water pressure) 1. Filter blockage.
2. Inlet pressure not sufficient to support watering.		 1. Check if the filter is blocked; if so, clean or replace the filter.
2. Ensure the timer is installed properly and not cross-threaded.
3. Install a booster pump or other auxiliary equipment to increase pressure.
El temporizador no riega (The timer does not water) 1. The dial is in the OFF position.
2. The faucet is not open.
3. The battery is depleted, it shuts down automatically.
4. Rain delay is ON.		 1. Turn the dial to the ON position.
2. After configuring, open the faucet.
3. Replace with new alkaline batteries.
4. Wait for the plan to resume.
La pantalla LCD está en blanco (LCD display is blank) 1. The LCD screen is not displayed under prolonged exposure.
2. The battery is depleted, it shuts down automatically.		 1. Avoid long-term exposure to sunlight.
2. Replace with new alkaline batteries.

Limpiando su Temporizador (Cleaning Your Timer)

After a period of use, impurities and dirt in the water can accumulate in the timer. Therefore, the timer should be cleaned regularly to ensure correct operation.

Please follow these steps to clean the timer:

  1. Close the garden faucet and remove the timer. Check if the filter at the water inlet of the timer has accumulated impurities.
  2. If the filter is dirty, please take it out of the timer and rinse it with running water. [Diagram of filter removal and rinsing]
  3. Turn on the Manual Watering Mode of the timer to open the valve and check if the timer's water pipe is blocked. If it is blocked, please clean it gently with a small cleaning brush. [Diagram of cleaning the timer's internal components]

Advertencias (Warnings)

  1. For outdoor use only. Placing the timer in a sheltered exterior will prolong its lifespan.
  2. To avoid damage, please tighten without using tools.
  3. The filter should be placed horizontally in the water inlet to prevent leaks.
  4. When power is low, please replace the batteries to avoid interruption of normal operation; when replacing batteries, please ensure that the battery tray is dry.
  5. When the timer is not in use, please remove the batteries and store them indoors.
  6. Do not use the timer at temperatures above 120°F (50°C) or below 38°F (3°C).
  7. Do not subject the product to extreme force or impacts.
  8. Serious electrical shocks could occur if water is sprayed into outlets or sources of electrical current. Never immerse the product in water.

This product is MADE IN CHINA and complies with the national standards of the United States, Great Britain, Germany, and France. Please use this product correctly. If it needs to be discarded, please dispose of it in accordance with national regulations. Please protect the environment.

[Recycling symbols and instructions in French]

EU REP
NAME: VIAJE ELECTRONIC COMPANY LIMITED
ADDRESS: E588, 13 ADELAIDE ROAD, DUBLIN, D02 P950, IRELAND
Email: VIAJEELE@outlook.com

[CE marking, battery symbols, Made in China]

Garantía (Warranty)

Rainpoint offers a 1-year warranty against manufacturing defects in materials and workmanship from the date of purchase. During the warranty period, Rainpoint will replace defective products free of charge under reasonable use and service, as determined solely by RainPoint. To submit a warranty request, please email service@rainpointus.com with your order ID, and we will respond within 24 hours.

Servicio de Atención al Cliente (Customer Service)

If you still have problems with the configuration, please search for "RainPoint" on YouTube for installation videos!

If the user manual does not have what you are looking for or you need other help, please contact us before returning the product to the store and let us know the LOT NO. of your device.

Email: service@rainpointus.com

WhatsApp: +1 626-780-5952

US Free Hotline (English): +1 833-381-5659 (MON-FRI 9:30 AM-5:30 PM PST)

UK Free Hotline (English Deutsch): +44 800-808-5337 (MON-FRI 9:00 AM–5:00 PM CET)

Models: ITV205, 2 Zone Digital Sprinkler Timer, ITV205 2 Zone Digital Sprinkler Timer, Digital Sprinkler Timer, Sprinkler Timer, Timer, Digital Hose Timers

PDF preview unavailable. Download the PDF instead.

66-RAINITV205-004 - 85x120mm-ITV205- 11.11 compressed 1 ?v=1671001570 CorelDRAW X8 iLovePDF

Related Documents

Preview RainPoint ITV105/ITV205 Quick Start Guide: Easy Lawn Watering
Get started quickly with your RainPoint ITV105 or ITV205 automatic water timer. This guide covers installation, setup, programming, and troubleshooting for efficient garden watering.
Preview RainPoint ITV205 Water Timer User Manual
Comprehensive user guide for the RainPoint ITV205 automatic garden hose timer, covering setup, programming for multiple zones, rain delay, manual watering, troubleshooting, and maintenance.
Preview RainPoint Water Timer Quick Start Guide
Concise guide to installing and programming RainPoint ITV105 and ITV205 water timers for efficient garden watering, including setup, troubleshooting, and warranty information.
Preview RainPoint ITV205-DLS 2-Zone Water Timer User Manual
Comprehensive user manual for the RainPoint ITV205-DLS 2-Zone Water Timer, covering installation, programming, features like rain delay and manual watering, and troubleshooting.
Preview RainPoint Mini Digital Tap Timer User Manual
Comprehensive user manual for the RainPoint Mini Digital Tap Timer (ITV105), covering installation, setup, features like rain delay and manual watering, troubleshooting, and warranty information.
Preview RainPoint 2-Zone Digital Tap Timer User Manual
User manual for the RainPoint 2-Zone Digital Tap Timer, Model NO. ITV205. This guide provides instructions on installation, programming, additional features like rain delay and manual watering, specifications, warnings, and warranty information.
Preview RainPoint 1-Zone Water Timer User Manual (Model ITV105)
Comprehensive user manual for the RainPoint ITV105 1-Zone Water Timer, detailing installation, programming, additional functions like Rain Delay and Manual Watering, troubleshooting, precautions, and warranty information.
Preview RainPoint ITV517 Digital Water Timer User Manual
User manual for the RainPoint ITV517 Multi-Programming Digital Water Timer, providing detailed instructions for installation, programming, and operation to optimize garden watering and conserve water.