Briloner Under-Cabinet LED Light

Introduction

Congratulations on your new Briloner Under-Cabinet LED Light. This manual provides essential information for safe assembly, operation, and maintenance.

Proper Use

This light is designed exclusively for indoor use in dry and enclosed spaces. It should be installed within reach for convenient switch operation and can be fitted to all normally inflammable surfaces. Any other use or modification is not permitted and may lead to damage or hazards.

Included Items

• 1 x Under-cabinet LED light, Model 14137306L
• 1 x Mains cable
• 1 x Connection lead
• 2 x Wall plugs
• 2 x Clips
• 2 x Screws
• 1 x Assembly and operating instructions

Description of Parts

• 1: Wall plug
• 2: Clip
• 3: Screws
• 4: Cap
• 5: Power cable
• 6: Light connection
• 7: ON/OFF switch
• 8: Connection cable
• 9: Light connection socket

Technical Data

Safety Instructions

General Safety:

• ? Read all instructions before use.
• Keep packaging materials away from children (suffocation hazard). ?
• Keep the product out of reach of children.
• This device may be used by children aged 8+ and persons with reduced capabilities if supervised or instructed.
• Do not allow children to play with the device or perform cleaning/maintenance unsupervised.

⚡ Danger of Electric Shock:

• Always unplug the device before cleaning or maintenance.
• Never immerse the light in water or clean with liquids/solvents.
• Ensure the light has cooled down before touching.
• Check power and connection cables for damage before use. Do not use if damaged.
• Ensure mains voltage matches the device's requirements.
• Never open electrical parts or insert objects.
• Only touch the insulated part of the plug when connecting/disconnecting.
• Damaged external cables must be replaced by the manufacturer or authorized service representative.

? Risk of Fire and Injury:

• Check for damage upon unpacking. Do not operate if defective.
• Do not look directly into the light source (LEDs).
• The LED illuminant is not replaceable; the entire light must be replaced when it reaches end-of-life.
• Risk of burns: Ensure the lamp is switched off and cool before touching.
• Do not use with external dimmers or electronic switches.
• Never leave the light operating unattended.
• Do not cover the light; excessive heat can cause fire.

Assembly Instructions

Required Tools & Materials (Not Included):

• Pencil / Marking tool
• Screwdriver
• Electric drill
• Drill bit (approx. 6mm)
• Spirit level
• Measuring tape

Fitting the Light:

1. Ensure a nearby power socket is accessible with the power cable (5).
2. Measure and mark the wall/mounting surface for drilling holes, using a spirit level for accuracy.
3. Drill mounting holes (approx. 6mm diameter, 30mm depth). Avoid damaging electrical cables.
4. Insert wall plugs (1) into the drilled holes.
5. Screw the clips (2) to the wall using screws (3).
6. Press the light into the secured clips (2).
7. Connect the power cable (5) to the light connection (6).
8. Plug the mains plug into a socket. The light is now ready.

Connecting Several Lights Together:

CAUTION! Ensure all lights are connected before plugging into the mains socket.

• Maximum of 10 lights of the same type can be connected to one socket.
• Ensure the distance between lights is not more than 16cm.
• Connect the power cable (5) to the first light's connection (6).
• Carefully remove the cap (4) from the light connection socket (9) of the first light using a screwdriver.
• Insert one end of the connecting cable (8) into the light connection socket (9).
• Insert the other end of the connecting cable (8) into the light connection (6) of the next light.
• Alternatively, connect directly via the socket (9) to the connection (6).
• Plug the mains plug into the socket.

Switching On/Off

Operate the ON/OFF switch (7) to turn the light on or off. (▶️ / ⏹️)

Maintenance and Cleaning

⚡ DANGER OF ELECTRIC SHOCK! Always unplug the device before cleaning.

Use only a dry, lint-free cloth for cleaning. Do not use water, liquids, solvents, or benzene.

Disposal

Dispose of the packaging and the device in an environmentally friendly manner according to local regulations. Observe packaging material markings for waste separation. [Recycling symbol]

Warranty & Manufacturer

Warranty: 36 months from date of purchase. Excludes damage from improper use or unauthorized modifications.

Manufacturer: Briloner Leuchten GmbH & Co. KG

Address: Im Kissen 2, 59929 Brilon, GERMANY

Contact: Tel.: +49 29 61/97 12–800, Fax: +49 29 61/97 12–199, E-Mail: kundenservice@briloner.com, www.briloner.com

Free Service Number: Tel.: 00800/27456637

Keep your receipt and product number (e.g., IAN 352698_2010) as proof of purchase.