Warranty Information

Limited One-Year Warranty

Hunter Fan Company provides a one-year limited warranty to the original purchaser of this accessory control, covering defects in material or workmanship. For service, contact Hunter Fan Company online at www.HunterFan.com/Support/Contact-Us/ or by phone at 1-888-830-1326. Proof of purchase is required.

What is NOT Covered

This warranty excludes labor costs for installation/removal, light bulbs/LEDs, remote control batteries, products purchased/installed outside the US, products owned by non-original purchasers, products without proof of purchase, products from unauthorized dealers, normal wear and tear, minor cosmetic blemishes, refurbished products, and damage due to improper installation, misuse, abuse, improper care, failure to follow instructions, accidental damage, modifications, incorrect maintenance/repair, power surges, improper parts/accessories, or acts of God.

Hunter is not responsible for consequential or incidental damages. State laws may affect warranty coverage.

Safety Warnings and Compliance

[WARNING] This product conforms to UL Standard 1917.

This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to conditions preventing harmful interference.

This equipment has been tested and complies with Class B digital device limits. It may cause radio frequency interference if not installed correctly. If interference occurs, try repositioning the antenna, increasing separation, or connecting to a different circuit. Unauthorized modifications may void operating authority.

Chemical Burn Hazard: Keep batteries away from children. This remote contains a lithium button cell battery. Swallowing or internalizing can cause severe burns and death within 2 hours. Always secure the battery compartment. If it does not close securely, stop use, remove batteries, and keep away from children. Seek immediate medical attention if batteries are swallowed or ingested. Dispose of cells properly.

Installation Instructions

The Hunter Wall Control requires a compatible receiver. Follow receiver installation instructions first.

For multiple remote-controlled fans on the same circuit, additional steps may be needed to prevent interference. Visit www.HunterFan.com/FAQs for details.

1. Step 1: Turn Off Power

   Before installation, use the [pull chains] to set the fan speed to HIGH and the light to ON. Ensure power is OFF at the outlet box and wall switch location. [WARNING] Disconnect power by turning off circuit breakers. All wiring must comply with national and local electrical codes (ANSI/NFPA 70). Consult a qualified electrician if unsure.

2. Step 2: Install Battery

   Slide the [battery compartment door] up to access the compartment. Replace used batteries with two AA batteries when needed.

3. Step 3: Install Wall Control

   Install the longer [screws] through the slots in the wall control into the switch box screw holes.

4. Step 4: Wire Wall Control

   Using [wire connectors], connect each black wire from the wall control to a black wire from the switch box. Connect the green with yellow stripe wire to the grounding wire from the switch box. If two white wires are present in the switch box, connect them to each other if not already connected.

5. Step 5: Install Wall Plate

   Install the shorter [screws] through the wall control plate and into the wall control screw holes.

6. Step 6: Turn On Power

   [IMPORTANT] Use the fan's pull-chain switch to set the fan speed to the HIGH position before operation. Turn power ON.

7. Step 7: Pair Wall Control

   To pair the remote to your Hunter receiver, PRESS AND HOLD the [(-) button]. WHILE HOLDING THE [(-) button], PRESS THE [(+) button] TWICE within three minutes of restoring power to the fan.

8. Step 8: Refer to Function Card

   Consult the included remote function card for information on how to use your wall control.

Troubleshooting

Remote Control of Fan is Erratic

• Ensure the battery is installed correctly.
• Install a fresh battery.

Multiple Remote Issues

If experiencing interference or faulty operation with multiple remote-controlled fans on the same circuit breaker, visit www.HunterFan.com/FAQs and search for "How do I properly install multiple remote-controlled fans?" for corrective information.

Remote Functions

• Quick Press [button]: Power On/Off
• Quick Press [button]: Increase Fan Speed
• Quick Press [button]: Decrease Fan Speed
• Long Press [button]: Fan High Speed
• Long Press [button]: Fan Low Speed
• Long Press [button] + 2X Quick Press [button]: Pair Function
• Long Press [button] + Long Press [button]: Fan Reverse (For fans without a reverse switch ONLY)