Product Identification and Specifications
GDW Reference: 0364
EEC Approval Number: e6*94/20*0080*00
| Specification | Value |
|---|---|
| D/ (Towing Capacity) | 7.20 KN |
| S/ (Vertical Load) | 75 kg |
| Max. (Towing Capacity) | 1200 kg |
GDW nv
Hoogmolenwegel 23, B-8790 Waregem
TEL: +32 (0)56 60 42 12 (ext. 5)
FAX: +32 (0)56 60 01 93
Email: gdw@gdwtowbars.com
Website: www.gdwtowbars.com
Diagrams and Visual Descriptions
Vehicle Image: A blue Peugeot 306 hatchback is shown.
Tow Bar Assembly Diagram: A technical drawing illustrates the tow bar components and their intended mounting points on the vehicle chassis. Key points are labeled A, B, and C, with additional bracket components labeled 'e' and 'f'.
Installation Instructions
- Remove the spare wheel.
- Make a cut in the bumper according to the provided sketch.
- Position the tow bar behind the chassis beams, ensuring points (A) and (B) of the tow bar align with the provided holes. Attach the mounting brackets (-e) and (-f) to the outside of the chassis, aligning their points (A) and (B) with the tow bar. Align the bracket points (C) with a pre-drilled hole in the crossmember next to the longitudinal member. Drill these holes to Ø10.5mm, extending into the luggage compartment. Enlarge the holes in the luggage compartment floor to Ø17mm and fit the raised washers.
- Attach the necessary bolts, washers, and nuts, and tighten everything securely.
- Mount part (*) and tighten securely.
- Replace the spare wheel.
Parts List (Composition / Samenstelling / Zusammenstellung)
- 1 x Tow bar (Reference 0364)
- 1 x Tow ball (T43M000)
- 4 x Bolts M12x40
- 4 x Washers M12
- 1 x Safety bracket
- 2 x Bolts M10x80
- 4 x Bolts M10x60
- 6 x Washers M10
- 6 x Nuts M10
- 2 x Raised washers (50mm)
- 1 x Mounting bracket (-e)
- 1 x Mounting bracket (-f)
All bolts and nuts are quality 8.8.
Important Notes (N.B. / Remarque / Hinweise)
- For the maximum permissible towing mass for your vehicle, consult your dealer or owner's manual.
- Remove any bitumen coating or anti-vibration material from the fastening points for the tow bar.
- Caution: When drilling, ensure you do not damage any brake lines, electrical wiring, or fuel lines.
Bumper Cut-out Description
The diagram illustrates the area of the bumper that needs to be cut out.
- "B" refers to the bumper itself.
- "O" indicates the lower rim of the bumper.
- "M" denotes the middle line of the bumper.
- The hatched area represents the section to be removed.
Torque Specifications
Bolts - Bolts - Bolts - Bolzen Quality 8.8
| Bolt Size | Torque (Nm) | Torque (kgm) |
|---|---|---|
| M6 | 10.8 | 1.1 |
| M8 | 25.5 | 2.60 |
| M10 | 52.0 | 5.30 |
| M12 | 88.3 | 9.0 |
| M14 | 137 | 14.0 |
| M16 | 211.0 | 21.5 |
Bolts - Bolts - Bolts - Bolzen Quality 10.9
| Bolt Size | Torque (Nm) | Torque (kgm) |
|---|---|---|
| M6 | 13.7 | 1.4 |
| M8 | 35.3 | 3.6 |
| M10 | 70.6 | 7.20 |
| M12 | 122.6 | 12.5 |
| M14 | 194 | 19.8 |
| M16 | 299.2 | 30.5 |
Design and Branding
The tow bar system is designed by GDW.
