ZALMAN X3 ATX Mid Tower Computer Case
User's Manual
Ver. 041220
Developed and designed by ZALMAN in Korea. This product is protected by ZALMAN's pending or registered patents.
For support and product information, visit www.zalman.com.
Note: To ensure safe and easy installation, please read the following precautions. Product design and specifications may be revised to improve quality and performance without notice.
Precautions
- Read this manual carefully before installing.
- Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
- Wear gloves to prevent accidents when installing the product.
- Severe damage may occur when mounting the system, so do not apply excessive force.
- Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
- Be careful not to block the ventilation hole of the product when using the system.
- Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
- Do not wipe the surface of the product using chemicals (organic solvents such as alcohol or acetone).
- Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
- Store and use the product out of children's reach.
- ZALMAN assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
- The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.
Specifications
| Model | X3 |
| Case Form Factor | ATX Mid-Tower |
| Dimensions | 430 x 210 x 459(H)mm |
| Weight | 9.1kg |
| Case Materials | Plastic, Steel, Tempered Glass |
| Motherboard Support | ATX / mATX / Mini-ITX |
| Maximum VGA Length | 350mm |
| Maximum CPU Cooler Height | 175mm |
| Maximum PSU Length | 180mm |
| PCI Expansion Slots | 7 |
| Drive Bays | 1 x Combo (3.5" or 2.5") or 1 x Combo (2 x 3.5"), 2 x 2.5" |
| Fan Support (Top) | 2 x 120mm, 2 x 140mm |
| Fan Support (Front) | 3 x 120mm, 2 x 140mm |
| Fan Support (Rear) | 1 x 120mm, 1 x 140mm |
| Pre-Installed Fan(s) (Front) | 3 x 120mm (with Addressable RGB LED Sync) |
| Pre-Installed Fan(s) (Rear) | 1 x 120mm (with Addressable RGB LED Sync) |
| Radiator Support (Front) | 120mm / 240mm / 280mm / 360mm |
| Radiator Support (Rear) | 120mm |
| I/O Ports | 2 x USB 3.0, 2 x USB 2.0, 1 x Headphone Jack, 1 x Microphone Jack, LED Control Button, Reset Button, Power Button |
Caution (Radiator support): A 280mm radiator can be problematic to install on the X3. The width of the radiator should be 140mm. If you wish to use a radiator larger than 140mm, please be sure to check the distance between the side of the radiator and the screw hole. If the distance is below 5.7mm, you can install it to the X3.
Included Accessories
- Accessories Box
- Glass Cleaner
- Cable Ties (x5)
- USB Media Rubber Covers (x4)
- USB Rubber Covers (x2)
- SSD/HDD Rubber (x4)
- HDD Screws (x8)
- SSD Screws (x4)
- SSD/MB Screws (x22)
- PSU/VGA Screws (x8)
- Motherboard Standoffs (x6)
- Standoffs Screw (x1)
Installation Guide
1. Removing the Side Panels
Illustration showing how to detach the side panels from the computer case.
2. Mounting the Motherboard
Diagram showing the placement of motherboard standoffs (labeled 1) and the motherboard being secured with SSD/MB screws (labeled 2).
Motherboard Sizes:
- ATX
- mATX
- Mini-ITX
3. Mounting the PSU
Diagram illustrating the installation of the Power Supply Unit (PSU) at the bottom of the case using PSU/VGA Screws.
4. Mounting the PCI-E(VGA) Card
Diagram showing the installation of a PCI-E (VGA) card into a motherboard slot within the case, secured with PSU/VGA Screws.
5. Graphics Card Holder
Diagram showing the attachment of a graphics card support bracket to the case interior.
6. Mounting the 3.5" and 2.5" SSD / HDD
Illustrations detailing the mounting of 3.5-inch HDDs and 2.5-inch SSDs/HDDs into designated drive bays. This involves using HDD Screws for 3.5" HDDs and SSD Screws for 2.5" SSDs/HDDs, placing them in the correct HDD or SSD screw positions.
7. Mounting the 2.5" SSD / HDD
Diagram showing the installation of 2.5-inch SSDs/HDDs onto specific mounting points within the case, secured with SSD/MB Screws.
8. Mounting the Top Fans
Diagram showing the installation of two fans at the top of the computer case.
9. Mounting the Front Radiator
Diagram illustrating the installation of a radiator at the front of the computer case. Includes a caution regarding radiator size compatibility.
10. RGB LED Controller
Detailed diagram of the RGB LED Controller and its connections:
- A: Fan 1~6 / 3-Pin: Connectors for up to six fans (4 pre-installed). Pins include GND, DC 12V, NC.
- B: Addressable LED 1~6 / 3-Pin: Connectors for addressable RGB LEDs (4 pre-installed). Pins include 5V, DATA, GND.
- C: RGB LED Control Button / 2-Pin: Connector for the RGB LED Control Button.
- D: LED 7~8 / 3-Pin: Connector for an LED strip bar.
- E: Gigabyte Motherboard Sync / 3-Pin: Connector for Gigabyte motherboards that support RGB Sync. Pins: 12V, DATA, GND.
- F: Other Motherboards Sync / 3-Pin: Connector for other motherboards that support RGB Sync. Pins: 5V, DATA, GND.
- G: SATA Power / 15-Pin: Connector to the PSU for power input (5V, 12V).
Caution: Ensure correct pin quantity and direction for Addressable RGB connectors before installation. Improper connection of the Addressable RGB 3-Pin connector to a 12V header instead of a 5V header may cause fatal damage to the product due to overvoltage.
RGB LED Controller Position: Diagram indicating where to mount the controller within the case.
Fan Specifications
Model: RFD 120A [X3]
Dimensions: 120 x 124 x 25 mm
Bearing Type: Hydraulic Bearing
Fan - Rating Voltage: 6~13.8 V DC
Fan - Rating Current: 150mA ±20%
LED - Rating Voltage: 4.5~5.3 V DC
LED - Rating Current: 800mA ±20%
Fan Speed: 800~1,500 ±10% RPM
Max Airflow: 34.34 CFM
Max Noise Level: 25.6 dB(A) ±10%
Connector: 3-Pin, 3-Pin Addressable
Weight: 160g
Life Span: 40,000 hrs
Cable Length: 580mm x 2
I/O Connectors
Diagrams illustrating the internal case connectors:
- POWER SW: Power Switch connector.
- RESET SW: Reset Switch connector.
- POWER LED: Power LED indicator connector.
- HDD LED: HDD activity LED connector.
- USB 3.0: Front panel USB 3.0 connector.
- USB 2.0: Front panel USB 2.0 connector.
- HD Audio: Front panel HD Audio connector.
Product Warranty
Warranty Period: 1 year from the date of purchase (with proof of purchase).
Free After-Sales Service (A/S): For product defects within the warranty period.
Paid After-Sales Service (A/S): For issues arising after the warranty period.
Service Exclusions (even within warranty):
- Failure to adhere to installation precautions in the manual.
- Damage due to user's intent, negligence, or carelessness.
- Damage or malfunction caused by unauthorized modification.
- Removal or damage to the warranty sticker.
- Damage caused by natural disasters.
- Malfunction due to use in environments with high humidity, dust, or foreign objects (e.g., insects).
Parts Retention Period: 2 years from the product's discontinuation date.
A/S Information:
- Operating Hours: Weekdays 10:00 AM - 4:00 PM (Closed on holidays, Saturdays, and Sundays).
- Service Application: Apply via website (www.zalmansvc.com) after registration. Visit the service center with the product or send via courier (prepaid).
- Service Center: Check the exact location and address on the website.
Shipping Costs:
- Initial Defect: Company covers round-trip shipping costs.
- Free A/S: Customer covers one-way shipping costs (prepaid).
- Paid A/S & Post-Warranty: Customer covers round-trip shipping costs.
Manufacturing Date Check: The manufacturing year and month are indicated in the serial number (e.g., '20' for 2020, 'A' for October).
Certification: Includes CE, EAC, FCC certifications for the RGB LED Controller (Model: ZM-RGBS6P-3S).
