DIHOOM Y661 Window Camera

Statement

Thank you for purchasing this product. DIHOOM is committed to providing customers with a reliable security solution and protecting their property at all times.

This is a quick setup guide to help you get familiar with this product faster.

While DIHOOM strives to make the manual complete and accurate, there might be discrepancies due to timely product updates. The detailed information provided is according to the final products.

Technical Support

If you need help, please contact service@dihoom.com before returning your product.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Responsible for compliance could void the user's authority to operate this equipment. For example, use only shielded interface cables when connecting to computer or peripheral devices. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:

The equipment complies with FCC Radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

FCC ID: 2A762-Y661

Product Details

Diagram showing the top view of the camera with 'Lens' labeled.

Diagram showing the bottom view of the camera with 'Reset Button' and 'TYPE-C charging port' labeled.

Diagram showing the back view of the camera with 'SD card Slot', 'Speaker', and 'Status LED' labeled.

Installing the "DIHOOM" app

Allow "DIHOOM" to access mobile data and WLAN to add devices. Allow "DIHOOM" to receive notifications to get alert notifications when motion is detected.

(The following QR codes are common to both iOS and Android)

QR code for Android/iOS app download.

Note: If you can't download the above app or can't connect to it, you can search and download the app "Eseecloud".

1. Click "Register"
2. Follow the steps to complete your account registration
3. Login

Advice:

• Make sure you use the correct email address.
• Select the correct region.
• When registering for a new account, please select the region where you are actually located. (Cross-region data sharing between your DIHOOM account is not supported.)

With the camera connected to power, press and hold the reset button for 5-10 seconds until you hear a tone, then release. Wait briefly for the "bip" tone, then begin Wi-Fi configuration through your app.

Place the camera and smartphone 1 to 3 feet (30 to 100 cm) away from the router to ensure a strong Wi-Fi signal.

Note: The camera supports both 2.4G wifi and 5G wifi.

Diagram showing a camera, a router, and a smartphone, with a distance indicator of 30cm~100cm.

Adding the Camera

Screenshots illustrating the process of adding a device via Bluetooth pairing in the DIHOOM app: tapping '+' to add device, scanning a QR code, and entering Wi-Fi password.

Screenshots showing 'Wait for Connection' and 'Device Added' status.

1. Enable Bluetooth & Wi-Fi on your phone.
2. In the DIHOOM App: Tap Devices → + → Network Camera (auto-detect in 30s).
3. Troubleshoot: Press camera's RESET button if failed → Retry. Enable Smart Detection Alarm manually post-setup.

1. Power camera → LED light flashes slowly.
2. Click the "+" → Scan QR code → Click Next → Select Wi-Fi (2.4/5GHz) → Enter password.
3. Wait for Connection Successful.

Need Help?

• Switch methods if one fails.

Key Notes:

• Keep phone near camera during setup.
• 5GHz Wi-Fi may require a stronger signal.
• Default alarm is OFF – activate manually.

Illustration of a smartphone scanning a QR code on a camera.

Mounting the camera

Place the camera on your window glass based on your preferred viewing angle. Ensure it's near a power outlet and close to your router for stable connectivity.

1. Remove the mounting sticker and peel off its top protective layer.
2. Attach the sticker to the window, then press the camera onto it.

Diagram showing a sticker being applied to a window, and then a camera being pressed onto the sticker.

3. Align the camera correctly—the arrow on the device should point upward. Keep the setup simple and double-check the camera's direction before securing it.

World map graphic with various FCC, CE, UKCA, and recycling symbols. Text indicates 'Made in China'.