SH16310N - COLUMN PATIO HEATER
Parts List
Diagram showing components for the SH16310N Column Patio Heater:
- 1. Lower body
- 2. Upper body
- 3. Base
- 4. Base cover
- 5. Cord grip
- 6. Screws for joint boards
- 7. Screws & washers for base
- 8. Joint boards
- 9. Allen key
You will also need a cross head screw driver. Assembly is much easier with two people and reduces the risk of damaging the product.
Step 1: Thread Cable
Image: Hand threading a plug and cable from the upper body (2) through a channel in the lower body (1).
Thread the plug and cable from the upper body (2) through the channel in the lower body (1). Make sure it goes all the way through.
Step 2: Connect Upper and Lower Body
Image: Sliding the upper body (2) onto the lower body (1).
Slide the upper body (2) on to the lower body (1).
Step 3: Fit Joint Boards
Image: Fitting joint boards (8) and securing them with screws (6) using the provided allen key (9).
Fit the joint boards (8) and secure with the screws (6) using the allen key provided (9).
Step 4: Prepare and Attach Base
Image: Unit turned upside down. Base (3) is placed inside the base cover (4), with the plug and cord threaded through the central hole.
Turn the unit upside down (put some cloth down to prevent scratches). Put the base (3) inside the base cover (4) and thread the plug and cord through the hole in the middle.
Step 5: Fasten Base to Unit
Image: Fastening the base to the main unit using screws & washers (7).
Fasten the base to the main unit using the screws & washers (7).
Step 6: Attach Cord Grip
Image: Fastening the cord grip (5) with a screwdriver, ensuring the lip faces upwards.
Fasten the cord grip (5). Make sure the lip faces upwards.
Refer to the manual that came with the product for operation guide.
SH16320N - BAR TABLE PATIO HEATER
Parts List
Diagram showing components for the SH16320N Bar Table Patio Heater:
- 1. Main body
- 2. Base cover
- 3. Base
- 4. Table top
- 5. Foot bracket
- 6. Allen keys (1 large + 1 small)
- 7. Screws & washers for base
- 8. Long screws + steel tubes
- 9. Screws for table top
You will also need a cross head screw driver. Assembly is much easier with two people and reduces the risk of damaging the product.
Step 1: Prepare Main Body
Image: Main body (1) of the patio heater turned upside down.
Turn the main body (1) upside down (put a cloth down to prevent scratches).
Step 2: Fit Base Cover and Thread Cable
Image: Base cover being fitted, with the plug and cord threaded through the central hole.
Fit the base cover and thread the plug and cord through the hole in the middle.
Step 3: Fit Base into Cover
Image: Base being fitted inside the base cover (2), aligning holes for screws.
Fit the base inside the base cover (2) and align the holes ready for the screws and washers.
Step 4: Attach Base Loosely
Image: Screws and washers being fitted into the base.
Fit the screws and washers. Leave them slightly loose for the moment. This allows a little movement in the base for the next part...
Step 5: Position and Attach Bar Base
Image: Someone holding the bar base (5) in position while long screws (8) are threaded through holes into steel tubes and into the bar base.
Get someone to hold the bar base (5) in position. Thread the long screws though the holes in to the steel tubes (8) and into the threaded holes on the bar base. Don't fully tighten them until all 3 are fitted.
Step 6: Tighten Long Screws
Image: Using the larger allen key to tighten one of the long screws.
Once all 3 of the long screws are fitted, tighten them all (using the larger allen key).
Step 7: Tighten Base Screws
Image: Using the smaller allen key to tighten a base screw.
Finally tighten the base screws as well (small allen key).
Step 8: Fit Cable Tie and Castors
Image: Fitting the cable to the cable tie and fitting castors.
Fit the cable to the cable tie and fit the castors.
Step 9: Attach Table Top
Image: Unit turned right way up, with the table top (4) being offered up. Hole (1) and bump (2) are visible for alignment.
Turn the unit the right way up again & offer up the table top. The holes must line up as shown. The bump (2) must align with the hole (1). This MUST be a 2 person task or you risk breaking the table top.
Step 10: Secure Table Top
Image: Using a screwdriver to fit screws securing the table top to the main unit.
Fit the screws to secure the table top to the main unit.
Refer to the manual that came with the product for operation guide.
SH16330N - PORTABLE PATIO HEATER
Parts List
Diagram showing components for the SH16330N Portable Patio Heater:
- 1. Main body
- 2. Base cover
- 3. Base
- 4. Cord grip & screws
- 5. Allen key
- 6. Deco board
- 7. Base screws & washers
You will also need a cross head screw driver. Assembly is much easier with two people and reduces the risk of damaging the product.
Step 1: Fit Deco Boards
Image: Fitting a deco board (6) into a slot on the patio heater.
Fit the deco boards (6) as shown.
Step 2: Prepare and Attach Base
Image: Base (3) placed inside base cover (2), with plug and cord threaded through the central hole. Mounting holes are aligned.
Put the base (3) inside the base cover (2) and thread the plugs and cord through the hole in the middle. Make sure the 2 mounting holes are aligned.
Step 3: Attach Base Assembly to Main Body
Image: Using an allen key to tighten screws (7) securing the base assembly to the main body (1).
Fit the base assembly to the main body (1) and tighten the screws and washers (7) as shown.
Step 4: Attach Cord Grip
Image: Fitting the cord grip (4) with a screwdriver, ensuring the lip faces upward.
Fit the cord grip (4) ensuring the lip faces upward.
Refer to the manual that came with the product for operation guide.
