Fiamma VENT 28 F Rooflight

Product Overview

This document provides installation and usage instructions for the Fiamma VENT 28 F Rooflight.

Product Name: VENT 28 F

Dimensions: Suitable for roof thicknesses between 54-68 mm.

Opening Size: Requires a 28 cm x 28 cm square opening.

Included Components:

• A: Rooflight Unit
• B: Inner Frame
• C: Mosquito Net Frame
• D: 4x Screws (35x60)

Part Numbers: Vent 28 F Crystal (C7902-02B), Spoiler Universal (06289-01-)

Weight: 1.8 kg

Installation Instructions

Please follow these steps carefully for proper installation:

1. Prepare Opening: Decide the installation location and cut a square opening of 28 cm x 28 cm in the roof. Ensure the roof thickness is compatible (54-68 mm).

   Diagram showing a 28 cm x 28 cm square opening being marked on a roof surface.

2. Seal External Frame: Apply sealant (e.g., SIKALASTOMER-710, THEROSTAT II, DEKALIN 1512) to the underside of the external frame with a minimum width of 10 mm, following the designated channels.

   Illustration of sealant being applied to the edge of the external frame.

3. Position External Frame: Place the external frame into the prepared opening. Ensure the hinges are oriented towards the front of the vehicle.

   Diagram showing the external frame being inserted into the roof opening, with hinges pointing forward.

4. Install Inner Frame and Secure: Place the inner frame and secure the rooflight using the 4 provided screws. Tighten the screws evenly to ensure the frame adheres flush to the roof without deformation. Recommended torque: 1.2 N.m.

   Illustration of the inner frame being fitted and screws being tightened, with a torque specification of 1.2 N.m.

5. Mount Mosquito Net: Attach the mosquito net frame using the special pressure hooks.

   Diagram showing the mosquito net frame being clipped into place.

6. Final Steps: Remove the protective plastic film from the cover. Avoid prolonged exposure to direct sunlight during this operation, as it may make it more difficult.

   Illustration showing the protective plastic being removed from the rooflight cover.

7. Opening Mechanism: Before opening the cover, remove the safety cable tie.

   Illustration showing the opening mechanism and a safety cable tie being removed.

Safety Instructions and General Advice

• Fiamma declines all responsibility for personal injury or property damage resulting from incorrect assembly or use. Keep instructions inside the vehicle.
• Assembly must be carried out according to instructions; do not modify the product.
• Before installation, check roof thickness compatibility (54-68 mm).
• Ensure the product does not interfere with adjacent accessories (luggage racks, cables, roof reinforcements, interior cabinets).
• Verify the roof's internal and external surfaces are flat.
• Periodically check screw tightness, especially after initial kilometers and before/after long trips.
• Lubricate the opening/closing mechanism with a few drops of grease if it becomes stiff.
• Do not walk on the product cover.
• Ensure the rooflight is properly closed before starting the vehicle.
• Periodically check the cover for cracks.
• Do not open the rooflight while the vehicle is moving, in strong wind, or rain.
• Remove snow or ice from the rooflight.
• Always comply with speed limits and traffic regulations. Adjust speed to traffic conditions and load.

Icons representing safe driving conditions (sun, moderate weather) and warnings (wind, rain, snow/ice, speed limit).

Care and Maintenance

• For internal and external cleaning, use only neutral, non-aggressive detergents.
• For cleaning the Crystal cover, use an acrylic glass cleaner and a soft cloth to avoid scratching.
• Never use aggressive products like glass cleaners, all-purpose cleaners, abrasives, or dish-washing detergents.
• Avoid alcohol-containing detergents, solvents, or corrosive liquids.
• The mosquito net can be cleaned with water and a neutral detergent after removing it from its fittings.

Troubleshooting and Contact

In case of problems, please contact your local dealer and provide the data from the nameplate.

Warranty Information

Fiamma warrants its products against defects in materials and manufacturing. The customer is entitled to warranty service in accordance with local laws and regulations of the country where the product was purchased.