Getting Started
Discover the RTB001, a cutting-edge, high-precision dynamic balancer tailored for RC tires. With high-precision sensors and precise stepping motors, this balancer sets new standards for weighing and positioning deficiencies with accuracy. Tailored for 1/10 and 1/8* On-Road cars, RTB001 ensures comprehensive dynamic balance detection. The large 2.8-inch TFT display provides clear and detailed information at a glance, and the intuitive interface enables you to navigate effortlessly. The built-in Bluetooth lets users control the balancer via the RC Gears app. With the RTB001, achieve optimal tire performance with visual data like never before!
Key Components:
- 01 2.8-inch TFT Display
- 02 Button
- 03 Fixture (To tighten sensor)
- 04 Lock (To install & remove tires)
- 05 DC Input (2.5 x 5.5 mm adaptor)
- 06 1/10 On-road adaptor
*Note: 1/10 on-road adaptor is included. 1/8 on-road adapter is sold separately!
Cautions
RTB001 is a high-precision instrument. Before use, pay attention to the following guidelines to ensure the optimal performance and longevity of the RTB001 instrument.
- Avoid exerting force on the protruding part of the motor shaft in any direction, even when installing the adaptors and tires. Forcing it may lead to damage to the internal sensor.
- Ensure that the operating surface is stable and free from vibrations. Ideally, place the instrument on a firm and level surface.
- Maintain a moderate airflow around the instrument and avoid exposing it directly to large objects such as air conditioners or fans.
- During usage, transportation, and storage, take precautions to prevent the instrument from falling or being subjected to excessive vibrations.
- When the instrument is not in use, kindly remove the tire from the adaptor and disconnect the power supply.
- It is strictly prohibited to touch the tire or forcibly stop the motor during detection rotation, as this may cause damage to the motor and sensor.
Operation
Install
To reduce the probability of damage to the sensor during transportation, the fixing screws of the sensor are not fully tightened during shipping and need to be tightened before use.
Step 1: Tighten the screws. Cautiously tighten the screw until it comes to a stop, and ensure that the mark line on the screw aligns perfectly with the base's mark line. This indicates that the screw is now secure and properly tightened, ensuring a safe and stable connection.
Step 2: Loosen the screw to remove the fixture.
Diagram shows loosening a screw, then removing a fixture.
Motor Shaft Correction
To correct a skewed motor shaft when the screw becomes loose during use, follow these steps:
- Remove the tire and the adaptor.
- Loosen the two screws on the base.
- Place the fixture in place and securely fasten with screws, as shown in the picture.
- Now, tighten the two screws.
- Loosen the fixture's screw and remove the fixture.
- Check and adjust the motor shaft to ensure it is correctly centered.
Tighten the adaptor. (Flat on the motor's D-shaft faces up. Align the fixture's screw onto the D-shaft's flat firmly.)
Diagram shows placing a fixture onto the motor shaft and securing it.
Get a Power Supply Ready
⚠️ WARNING: Abnormal Input Voltage
The balancer requires a 12-18V DC power supply with a 2.5mm internal diameter pin. If the power supply falls outside this specified voltage range, a warning prompt will appear.
Diagram shows a DC input port labeled "DC INPUT 12-18V" with a 2.5mm pin icon.
Calibration
Once the balancer is installed, if you encounter any accuracy issues that environmental changes may have caused during the initial use or throughout the operation, please proceed with the calibration process.
- Step 1: Power on with the button ? pressed.
- Step 2: Shortly press the button ? to continue.
- Step 3: Weigh the adaptor and short-press ? to continue.
- Step 4: Key in the weight of the adaptor (Short-press ? to key in, press ? to switch the unit).
- Step 5: Put on the adaptor and tighten it with the screw.
Diagrams illustrate each step: powering on, pressing button, weighing adaptor, inputting weight, and attaching adaptor. A screen shows "Calibrating..." and then "Calibrated!".
Upon completing the calibration, shortly press the button ? to access the normal checking mode.
Tire Balancing
1. Self-Check Test
The startup screen will be displayed upon powering on, followed by the tire model selection page. The default mode is "Automatic Mode". Press and hold the button ? to enter the tire installation page. The actual tire is not needed for the self-test. Shortly press the button ? to start the test. "Checking..." will show during the testing process, and "Balanced" will appear when the self-test is done. If "Balanced" does not appear, calibration is required.
- Step 1: The default mode is "Automatic Mode" ⚙️.
- Step 2: Prompt to install the tire, click ? to continue.
- Step 3: Device displays "Checking..."
- Step 4: "Balanced" appears, indicating self-test is done.
Diagrams show the sequence: selecting "Automatic Mode", a prompt to install the tire, the "Checking..." screen, and the final "Balanced" screen with a message to remove the tire.
2. Tire Checking
Choose Tire Type
The startup screen will be displayed upon powering on, followed by the tire model selection page.
- Automatic Mode: The tire type will be detected automatically.
- 1/10: 1/10 on-road tire
- 1/8: 1/8 on-road tire
The default mode is "Automatic Mode" ⚙️. Press and hold the button ? to continue.
Screenshots show tire type selection: "Automatic Mode", "1/10", "1/8", with an option to switch and a prompt to press and hold to continue.
Tire Installing
Twist off the nut on the tire adaptor. Ensure that the hexagon of the nut matches the hexagon of the tire. Press the lock ? on the balancer to secure the adaptor. Twist the nut clockwise to attach the tire to the adaptor. Wait 3-5 seconds and then short press the button ? to enter the next step.
Diagram shows twisting off a nut, aligning a tire adaptor, pressing a lock, and attaching a tire.
Checking
The motor will perform 25 clockwise rotations while ensuring the table remains level, vibration-free, and with minimal airflow. DO NOT TOUCH the tires or forcefully brake the motor throughout this process.
Diagram shows the device in operation with the motor spinning.
Result
Balanced: Please remove the tire! Press the locker ? to twist the nut counterclockwise to remove. Short-press ? to return, or you can turn off the power.
Imbalanced: Weigh the balancing putty to match as indicated on display and shape the putty into a ball if needed. Affix the weight on the tire as the notch arrow indicates at the bottom plate.
After putting the counterweight as prompted, users may need to conduct it repeatedly to get balanced. This process may require iteration when certain tires have multiple counterweight points. After adding weight, press the button ? again to perform the test. Hold and press the button ? to return to the Tire Type page.
Diagrams show weighing putty and affixing it to the tire rim at a specific position indicated by an arrow.
Technical Specifications
- Voltage:
- DC12V~18V
- Standby Current:
- ≤70mA
- Working Current:
- 12V/≤750mA, 18V/≤550mA
- DC Input Interface:
- Ø5.5mm DC Jack with I.D 2.5mm pin, inner Positive(+), outer Negative(-).
- Compatible Tires:
- 1/10 & 1/8 on-road
- Display:
- 2.8-inch TFT
- Size:
- 178(L) * 99(W) * 106(H)mm
- Communication:
- Bluetooth 5.0
- Transmission distance:
- ≤15m
- Working temperature:
- 0°C~40°C
- Working humidity:
- 10%~80% (Non-condensing)
- Storage temperature:
- -10°C~60°C
- Storage humidity:
- 20%~70% (Non-condensing)
- Weight:
- about 800g
What is Included
- RC Tire Balancer (RTB001) *1
- 1/10 Tire Adapter *1
- Fixture *1
- DC Power Cable *1
- Manual *1
- Balancing Putty (10g) *1
- Carrying Case *1
Image shows all the listed items laid out.
Connect to the App
Scan the QR code to install the RC Gears app.
QR code image is present. Text indicates availability on "App Store" and "Google Play".
After the balancer is powered on and the start-up screen is displayed, enable Bluetooth on your smartphone. The app will search and find the balancer. Tap the device in the list to connect. All pages of the App and the displays of the device are fully synchronized and interact with each other seamlessly.
Screenshots show the app sequence: "Select the device to connect", "Choose the tire type, tap Next", "Install the tire, tap Next", "Checking...", "Balanced! Tap DONE to return to Tire Type page.", "Imbalanced! Tap Exit to return to Tire Type page, or Tap Start Over to check again!".
Warranty and Service
SkyRC TECHNOLOGY CO., LTD. guarantees this product to be free of manufacturing and assembly defects for a period of one year from the time of purchase. The warranty only applies to material or operational defects that are present at the time of purchase. During that period, SkyRC will repair or replace, free of service charge, products deemed defective due to those causes. This warranty is not valid for any damage or subsequent damage arising as a result of misuse, modification, or failure to observe the procedures outlined in this manual.
Note:
The warranty service is valid in China only. If you need warranty service overseas, please contact your dealer in the first instance, who is responsible for processing guarantee claims overseas. Due to high shipping costs and complicated custom clearance procedures to send back to China, SkyRC cannot provide warranty service to overseas end-users directly. If you have any questions not mentioned in the manual, please feel free to send an email to support@skyrc.com.
