Assembly Instructions

Dresser Model: B850-DR

Step 1: Open the bottom drawer and remove the Bunfoot carton (B). Assemble the Bun Foot (B) with JCBC Bolt (1), Spring washer (2), Flatwasher (3), and secure with Allen Key (4) as shown. For ease of installation, it is recommended to flip the dresser over onto a soft surface.

Box 1: Box of Dresser Contents:

• A: Dresser (1 pc)
• B: Bun Foot (4 pcs)
• C: Bottom Center Leg (1 pc)

Box 1: Hardware List:

1. JCBC Bolt m6x50mm Blk (4 pcs)
2. Spring Washer 1/4" Blk (4 pcs)
3. Flat Washer 1/4"IDx13mmOD Blk (4 pcs)
4. Allen Key m4x110mm With Ball Blk (1 pc)
5. Tipping Restraint (1 pc)

Completed Assembly: The dresser is assembled with bun feet and a center leg. An anti-tip kit is included for safety.

Note: Periodically tighten screws as they may loosen with use. Check tightness of all screws every 6-8 weeks.

Eastern King Bed Model: B850-EKB

Step 1.1: Attach Head Board Leg (C) to Head Board (A) using JCBC BOLT (1), Spring Washer (2), Flat washer (3), and secure with ALLEN KEY (4). Repeat for the other side.

Step 1.2: Fix the remaining holes with Csk Screw (6) as shown.

Step 2: Hook the Side Rail (F) to the Head Board (A) and push down to fit. Repeat this step with the other end of the rail to hook onto the Footboard (B).

Step 3.1: Tighten the four corners using Allen Key (5).

Step 3.2: Fix the Bed Slat Support Leg (E) to the Bed Slat (D) as shown.

Step 3.3: Install the bed slat (D) to the side rail (F) and tighten with Csk Screw (6) using a screwdriver. Ensure the setup is done at the decided location for the bed to obtain perfect stability. Push the side rail (F) to meet the wooden slat (D) and fix with the CSK screw (6).

Box 1: Box of Headboard & Footboard Contents:

• A: Headboard (1 pc)
• B: Footboard (1 pc)
• C: Headboard Leg (2 pcs)
• D: Bed Slats (4 pcs)
• E: Bed Slats Support (8 pcs)
• F: Side Rail (2 pcs)

Box 1: Hardware List:

1. JCBC M6 x 40mm (4 pcs)
2. SPRING WASHER 1/4" Blk (4 pcs)
3. Flat Washer 1/4"ID x 13mmOD Blk (4 pcs)
4. ALLEN KEY m4x65mm Blk (1 pc)
5. ALLEN KEY m5x65mm Blk (1 pc)
6. Csk m4 x 32mm Rbw (16 pcs)

Completed Assembly: The Eastern King bed is fully assembled with headboard, footboard, side rails, and slats.

Note: Periodically tighten screws as they may loosen with use. Check tightness of all screws every 6-8 weeks.

Night Stand Model: B850-N

Step 1: Open the bottom drawer and remove the Bunfoot carton (B). Assemble the Bun Foot (B) with JCBC Bolt (1), Spring washer (2), Flatwasher (3), and secure with Allen Key (4) as shown. For ease of installation, it is recommended to flip the night stand over onto a soft surface.

Box 1: Box of Night Stand Contents:

• A: Night Stand (1 pc)
• B: Bun Foot (4 pcs)

Box 1: Hardware List:

1. JCBC Bolt m6x50mm Blk (4 pcs)
2. Spring Washer 1/4" Blk (4 pcs)
3. Flat Washer 1/4"IDx13mmOD Blk (4 pcs)
4. Allen Key m4x110mm With Ball Blk (1 pc)

Completed Assembly: The night stand is assembled with bun feet.

Note: Periodically tighten screws as they may loosen with use. Check tightness of all screws every 6-8 weeks.