ASSEMBLY INSTRUCTIONS BATH VANITY-CABINET

Thank you for purchasing this quality product. Be sure to check all packing material carefully for small parts which may have come loose inside the carton during shipment. Separate, identify and count all parts and hardware. Compare with the parts list to be sure all parts are present. DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED.

* Use of power tool to assemble this product will invalidate any claim and damage this product making unsafe !!!

* Please assemble on a clean soft surface to avoid damage.

Tools Required:

• Screwdriver (Not included)
• Allen Key (Not included)

IMPORTANT: PLEASE READ INSTRUCTION BEFORE STARTING THE ASSEMBLY

Important Information

PLEASE DO NOT RETURN TO STORE ? STOP

Please do not return this product to the retailer!! We are able to assist you in ANY way.

If you find that you have any trouble with assembly or missing or damaged parts please contact the seller.

Before Installation

Important – Please read these instructions fully before starting assembly.

Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts, which may have come loose inside the carton during shipment. Identify and count all items according to the PARTS LIST and/or HARDWARE LIST shown below. Check you have all the components and tools listed on the following pages.

• We recommend that you assemble this product with the assistance of another person; this will make the assembly easier, and will help eliminate damage to the product or injury to persons during assembly.
• Please do not over tighten screws or bolts until the assembly is completed.
• Keep children and animal away from the work area, small parts could choke if swallowed.
• Please put all parts on a non-abrasive floor before assembly, and follow the assembly steps to assemble your newly purchased product correctly and efficiently.

Cam Lock Assembly Instructions

Diagram A: Insert Cam Bolt into hole as shown in diagram A.

Diagram B: Make sure not to insert the Cam Bolt too deep as shown in figure B, as this will cause the Cam Lock to be misaligned and unable to interlock properly.

Diagram C: Also avoid inserting the Cam Bolt too close to the surface of the hole as shown in figure C, as this will cause the Cam Lock to be too loose, and not interlock properly.

Connect the panels together.

Insert the Cam Lock so the side opening fits over the head of the Cam Bolt.

To tighten the Cam Lock, turn it clockwise on half a turn with a flat screwdriver. *Do not use an automatic screwdriver as it may bend or break if too much power is imposed.

Detail View

The following diagram shows an exploded view of the vanity-cabinet, illustrating the placement of various numbered parts before assembly.

Part Lists - N710P195628

Hardware Lists - N710P195628

Assembly Steps

STEP: 1

Attach the 'Top Rear Crossbar' (11) to two 'Support Pieces' (12) using two 'Round Head Screws' (D) per connection. Attach the 'Bottom Rear Crossbar' (18) to two 'Support Pieces' (12) using two 'Round Head Screws' (D) per connection. Attach the 'Mid Front Crossbar' (8) to two 'Support Pieces' (12) using two 'Round Head Screws' (D) per connection. On the 'Mid Front Crossbar' assembly, attach two 'Plastic Door Magnets' (L) to the 'Support Pieces' (12) using two 'Handle Screws' (M) per magnet.

STEP: 2

Attach 'Three in one bolts' (B) to the designated holes on 'Side Panel (L)' (1) and 'Side Panel (R)' (2). Attach 'Three in one bolts' (B) to the designated holes on 'Top Front Crossbar' (4), 'Side Front Crossbar(L)' (5), 'Side Front Crossbar(R)' (6), and 'Mid Front Crossbar' (8).

STEP: 3

Attach 'Three in one bolts' (B) to the designated holes on the 'Bottom Frame' (10). Attach 'Three in one bolts' (B) to the designated holes on the 'Top Rear Crossbar' (11), 'Side Rear Crossbar (L)' (13), 'Side Rear Crossbar (R)' (14), and 'Mid Rear Crossbar' (17).

STEP: 4

For the 'Side Mid Crossbar (L)' (15), insert a 'Three in one lock' (C) into the larger hole and a 'Wood dowel' (A) into the smaller hole. Attach this assembly to the 'Side Front Crossbar(L)' (5) using two 'Three in one locks' (C) and two 'Wood dowels' (A). Repeat for the 'Side Mid Crossbar (R)' (16) and 'Side Front Crossbar(R)' (6). The diagram shows a close-up of how to align and insert the cam lock and bolt.

STEP: 5

Assemble the frame structure. Attach the 'Mid Front Crossbar' (8) to the 'Side Front Crossbar(L)' (5) and 'Side Front Crossbar(R)' (6) using 'Three in one locks' (C) and 'Wood dowels' (A). Attach the 'Fake Drawer' (7) to the assembly using 'Three in one locks' (C) and 'Wood dowels' (A). Attach the 'Top Front Crossbar' (4) to the structure using 'Three in one locks' (C) and 'Wood dowels' (A).

STEP: 6

Attach the 'Mid Panel' (3) to the partially assembled frame. Connect it to the 'Side Front Crossbar(L)' (5) and 'Side Front Crossbar(R)' (6) using 'Three in one locks' (C) and 'Wood dowels' (A).

STEP: 7

Assemble the rear frame. Attach the 'Top Rear Crossbar' (11) to the 'Side Rear Crossbar (L)' (13) and 'Side Rear Crossbar (R)' (14) using 'Three in one locks' (C) and 'Wood dowels' (A). Attach the 'Mid Rear Crossbar' (17) to the structure using 'Three in one locks' (C) and 'Wood dowels' (A).

STEP: 8

Connect the front assembly from Step 5 to the rear assembly from Step 7. Attach the 'Top Rear Crossbar' (11) and 'Mid Front Crossbar' (8) to the 'Mid Panel' (3) using 'Three in one locks' (C) and 'Wood dowels' (A).

STEP: 9

Continue assembling the main cabinet structure. Attach the 'Mid Rear Crossbar' (17) and 'Bottom Front Crossbar' (9) to the 'Side Panel (L)' (3) and 'Side Panel (R)' (2) using 'Three in one locks' (C) and 'Wood dowels' (A). Attach the 'Mid Front Crossbar' (8) to the structure using 'Three in one locks' (C) and 'Wood dowels' (A). Attach 'Hex-Head bolts' (F) to connect parts as shown.

STEP: 10

Continue assembling the main cabinet. Attach the 'Side Panel (L)' (1) and 'Side Panel (R)' (2) to the frame. Secure the 'Top Rear Crossbar' (17), 'Bottom Front Crossbar' (9), 'Mid Front Crossbar' (8), and 'Top Front Crossbar' (4) to the side panels using 'Three in one locks' (C) and 'Wood dowels' (A). Attach 'Hex-Head bolts' (F) as indicated.

STEP: 11

Attach the 'Bottom Rear Crossbar' (18) to the 'Side Panel (L)' (1) and 'Side Panel (R)' (2) using two 'Round Head Screws' (D).

STEP: 12

Attach the 'Bottom Frame' (10) to the top of the assembled cabinet structure. Secure it using 'Three in one locks' (C) and 'Wood dowels' (A) on both 'Side Panel (L)' (1) and 'Side Panel (R)' (2).

STEP: 13

Attach 'Damping hinges' (E) to the 'Door Cabinet (L)' (20) and 'Door Cabinet (R)' (21) using 'Handle Screws' (M) and 'Plastic Door Magnets' (L). Ensure the hinges are oriented correctly.

STEP: 14

Attach the 'Door Cabinet (L)' (20) and 'Door Cabinet (R)' (21) to the main cabinet body. Use 'Handles' (J) and 'Handle Screws' (K1) to attach the handles to the drawer faces and doors. The diagram shows detailed hinge adjustment screws.

STEP: 15

Attach 'Shelf Pins' (H) to the inside of the cabinet at the desired heights for the adjustable shelves. Place the 'Adjustable Shelves' (19) onto the shelf pins.

STEP: 16

Place the 'Adjustable Shelves' (19) into the cabinet. Secure them using 'Round Head Screws' (I) through the designated holes.

STEP: 17

Assemble the drawers. Attach 'Three in one bolts' (B) to the 'Bottom Panel' (26). Assemble the drawer sides ('Rear Drawer Panel' (25), 'Side Drawer Panel (L)' (23), 'Side Drawer Panel (L)' (24)) and the 'Bottom Panel' (26) using 'Three in one locks' (C), 'Plastic Canopies' (N), and 'Round Head Screws' (O). Attach 'Handles' (J) to the 'Drawer Face' (22) using 'Handle Screws' (K2). Insert the assembled drawers into the cabinet runners.

STEP: 18

Insert the assembled drawers (part 22) into the cabinet. The diagram shows the drawer slides and how they engage.

STEP: 19

Attach the 'Anti fall Hardware' (P) to secure the vanity-cabinet to the wall for safety. Follow the instructions provided with the hardware kit.

STEP: 20

Install the sink on the cabinet with glue. Let stand for 24 hours. *Silicone glue is not included in the package to comply with safety regulations in certain shipping conditions.

STEP: 21

The final assembled Bath Vanity-Cabinet is shown. The diagram indicates that instructions should not be discarded ❌.

HINGE ADJUSTMENTS

This section provides guidance on adjusting the cabinet doors using the hinges.

1) Sideways / Tilt adjustment

Turn the screw clockwise to move the door further away from the side of the cabinet. Turn the screw anticlockwise to move the door closer to the side of the cabinet. Arrows indicate movement direction.

2) & 4) Height adjustment

While supporting the weight of the door, turn the screws. Clockwise to move the door up. Anticlockwise to move the door down. Arrows indicate vertical movement.

3) Forward and back adjustment

If the gap between the back of the door and the cabinet is too small, and the door may not close fully. Turn the screw clockwise to decrease the gap between the door and the cabinet. Turn the screw anticlockwise to increase the gap between the door and the cabinet. Arrows indicate depth adjustment.