DEJSA Ceiling Lamp
Important Safety and Installation Information
For indoor use only.
⚠️IMPORTANT! Always shut off power to the circuit before starting installation work. In some countries, electrical installation work may only be carried out by an authorized electrical contractor. Contact your local electricity authority for advice. Different materials require different types of fittings. Always choose screws and plugs that are specially suited to the material.
Assembly Steps
Step 1: Attach Mounting Bracket
Attach the mounting bracket to the main lamp body. Use the provided screws (2x) and tighten them securely with a screwdriver.
Diagram Description: A diagram shows the ceiling mount bracket being connected to the main lamp housing. Close-up views show two screws being inserted and tightened with a screwdriver, indicated by circular arrows showing rotation. An upward arrow indicates the direction of attachment.
Step 2: Prepare Ceiling Mount
Prepare the ceiling mount bracket for installation. Feed the wires through the bracket.
Diagram Description: A diagram shows the ceiling mount bracket with holes for screws and wires passing through it, ready to be attached to the ceiling. An upward arrow indicates the direction of mounting.
Step 3: Connect Lamp Body to Bracket
Connect the main lamp body to the ceiling mount bracket. Route the wires through the designated opening.
Diagram Description: The main lamp body is shown being attached to the ceiling bracket. Wires are being guided into the housing. A curved arrow indicates the direction of attachment.
Step 4: Wire Connection Preparation
Connect the wires using the provided connector block. Ensure a secure connection.
Diagram Description: A close-up shows a wire being inserted into a terminal block connector. An arrow indicates the direction of insertion.
Step 5: Strip Wire Insulation
Prepare the wires for connection. Strip approximately xx mm (xx") of insulation from the ends of the wires.
Diagram Description: A diagram shows wires being measured with a tape measure to indicate the length of exposed wire (xx mm / xx inches). Arrows show the direction of insertion.
Step 6: Insert Wires into Conduit
Insert the prepared wires into the appropriate conduits or connectors. Ensure a secure fit. Strip 20 mm (13/16") of insulation from the wire ends.
Diagram Description: A diagram shows a wire being inserted into a protective sleeve or conduit. Another measurement (20 mm / 13/16") is indicated for wire stripping. An info icon (?) is shown next to the measurement. Arrows show the direction of insertion.
Step 7: Connect Wires to Terminal Block
Connect the wires to the terminal block inside the lamp housing.
Diagram Description: A diagram shows wires being connected to a terminal block. Arrows indicate the direction of connection.
Step 8: Electrical Wiring
Wire the lamp according to the diagram: connect Live (L) to L, and Neutral (N) to N. Ensure correct polarity.
Diagram Description: A diagram illustrates the electrical connections, showing Live (L) and Neutral (N) wires being connected to corresponding terminals in a connector block. Arrows show wires being inserted into terminals.
Step 9: Secure Wiring and Cover
Secure the wiring and close the connector cover.
Diagram Description: A diagram shows the wire connector cover being closed and secured over the connected wires. Arrows indicate the direction of closing.
Step 10: Attach Lamp Body to Mount
Attach the main lamp body to the ceiling mount bracket.
Diagram Description: The main lamp body is shown being secured to the ceiling bracket. An arrow indicates the direction of movement.
Step 11: Final Lamp Body Attachment
Final attachment of the lamp body to the ceiling mount.
Diagram Description: The lamp body is shown being fully attached to the ceiling mount.
Step 12: Install Light Bulbs
Install the light bulbs into the sockets. Screw them in gently until snug.
Diagram Description: A diagram shows light bulbs being screwed into the lamp sockets. Circular arrows indicate screwing action.
Step 13: Attach Glass Shades
Attach the glass shades to the lamp. Twist them into place until secure.
Diagram Description: A diagram shows a glass shade being attached to a lamp holder by twisting it. A large curved arrow indicates twisting action.
Product Information
Product Name: DEJSA
Brand: IKEA
Document Number: AA-2250759-5
This is a 3-light ceiling lamp designed for indoor use.
Diagram Description: The first page shows the product name 'DEJSA' and the IKEA logo. Page 8 shows tools required: a screwdriver with a cross symbol (❌), scissors, and a tape measure. It also depicts a person contemplating assembly and another on the phone, along with the product with '3x' indicating three shades.
