Part No. 1034030: The Cure Jet® and 7700-HD Mounting Bracket Kit for Loctite® Robots
Description
The 1034030 mounting bracket kit is designed for holding the Cure Jet or the 7700-HD LED light source when using Loctite® 3-axis robots. The "C" rail connection allows for more than one bracket to be used when using 3-axis robots. This configuration enables multiple dispense points and curing processes to increase throughput. A mounting rail, plate, or adapter must be purchased separately to mount the brackets on the robot.
Diagram Description: Illustrates the Loctite Cure Jet and 7700-HD LED light sources, along with the mounting bracket components including the 'C' bracket, mounting plate, and various screws.
Includes
| Qty | Description |
|---|---|
| 1 | Cure Jet and 7700-HD mounting bracket kit |
Instructions for Use
Mounting Cure Jet – Use (1) M4 x 32 mm and (1) M4 x 12mm Phillips head screws.
Mounting 7700-HD – Use (2) #10-32 x 3/8" Phillips head screws.
Diagram Description: Visual representations of the screws required for mounting the Cure Jet and 7700-HD, and the 'C' bracket sliding onto the 'T' shaped mounting rail for 3-axis robots.
3 Axis Bench top Robots Installation:
- Attach the mounting rail to the robot using the two M5 x 12 mm socket head cap screws.
- Slide the "C" bracket on the back of the mounting plate over the "T" shaped mounting rail.
- Fix the position of the mounting plate by manually tightening the socket head cap screw.
Parts and Accessories
Required: *** Must Be Purchased Separately ***
For 3 Axis Bench top Robots: One of the three mounting rails listed below is required. The mounting rail is mounted directly to the robot. The "C" bracket on the mounting plate then slides over the mounting rail, which has a "T" shape. The small rail is used for a single dispense point, while the larger rails are used for multiple dispense points.
| Part No. | Description |
|---|---|
| 98328 | 3 3/4 inch bar with two cap screws |
| 98329 | 8 3/4 inch bar with two cap screws |
| 98330 | 12 inch bar with two cap screws |
| 98325 | 360 Degree Rotation Kit |
Optional Accessories
Integrated Dispense Controllers
These are reservoirs integrated with digital dispense controllers. When connected to the dispense valve, they offer a complete dispensing solution.
| Part No. | Description |
|---|---|
| 97007 | Integrated Semiautomatic Controller and Reservoir, 0-100 psi |
| 97010 | Integrated Semiautomatic Controller and Reservoir, 0-15 psi |
| 97017 | Integrated Semiautomatic Controller and Reservoir, 0-100 psi, with low level sensor |
| 97020 | Integrated Semiautomatic Controller and Reservoir, 0-15 psi, with low level sensor |
Solenoid Valve Module
This is used to control the valve directly using the I/O from the robot. If this unit is purchased, any pressure reservoir can be used to supply adhesive to the valve.
| Part No. | Description |
|---|---|
| 988000 | Solenoid valve module. |
Tip Locator Bracket
The tip locator bracket is used to mechanically set the tip height during installation so that the program does not need to be corrected after a tip change. These are sized for 1" long, 25 gauge needles and must be modified by the user for larger gauge sizes.
| Part No. | Description |
|---|---|
| 98335 | Tip locator bracket for 97113 or 97114 valves |
Z-Height Adjustment Plate
When using a mounting rail attached directly to the robot, it may not be possible to bring the dispense tip in contact with a flat part on the 400 Series robot. When using the 200 series robot, a large part may require that the dispense tip be mounted further away. This plate allows for up to 6" of rough adjustment of the location of the mounting bracket above or below the mounting hole in the robot.
| Part No. | Description |
|---|---|
| 98357 | Z height adjustment plate |
