Loctite CL10 Single LED Controller

2 Overview

The Loctite CL10 Single LED Controller is a UV light source designed to emit a spot of light at wavelengths of 365nm or 405nm. It is utilized in adhesive Light Cure bonding applications.

Advantages:

• Over 20,000 working hours.
• No IR emission, resulting in low-temperature curing and preventing damage to parts from heat emission.
• Up to 90% energy savings compared to mercury arc lamps.
• Compact LED head suitable for handheld or fixed fixture applications.
• Operates via foot switch actuation or PLC remote control.
• Supports timed mode or manual cycling.
• Low maintenance cost.

3 Technical Data

4 Installation

Please check the unit for any mechanical defects. If shipping damage is present, do not install or use the equipment and immediately contact the shipping company and supplier.

4.1 Capacity

Diagram showing minimum space required for the equipment: a box representing the controller with 50mm clearance on the sides and 30mm clearance above and below.

4.2 Dimension

Diagram showing the dimensions of the Loctite CL10 Single LED Controller. The main unit is approximately 62.0mm (2.44 inches) wide and 150.0mm (5.91 inches) high. A side view shows a depth of 64.0mm (2.52 inches). The front panel features a display showing 'Intensity % 100' and 'Time S 20.0', with SET and arrow buttons below. It also indicates the item number 1514636.

4.3 Caution

• To prevent heat damage, position the unit horizontally on a level surface. Improper positioning may cause damage.
• Avoid placing the unit next to high voltage equipment or heat sources.
• Ensure no objects are placed on the power cable.

4.4 Installation Flow

1. Place the controller horizontally on a level surface.
2. Connect the power cable to the controller using the supplied power cable. The power connector is labeled 'XS-1' and indicates AC 100-240V 50/60Hz with a fuse rating of 2AMP 250VAC.
3. Connect the LED head to the connector labeled '' located under the power button.
4. Caution: Press the power switch to turn on the LED head; press again to turn off. When using a PLC or extension cable, a '0V' indication means the LED head is working.
5. Connect the foot switch or PLC (optional) to the connector labeled ''.

5 Controller Button and Operating

5.1 Component Name and Function

Diagram of the controller front and rear panels with numbered components:

• 1. Power Switch: Turns the unit On/Off.
• 2. LED Head Connector: Port for connecting the LED head.
• 3. Intensity Display: Shows intensity setting data, easy to read and edit.
• 4. Time Display: Shows time setting data, easy to read and edit.
• 5. Up Arrow Button: Used for adjusting settings.
• 6. SET Button: Confirms selections or enters menus.
• 7. Down Arrow Button: Used for adjusting settings.
• 8. Power Cable Connector: Port for the AC power cable.
• 9. Control Port (XS-1): Input for LED head control signals (e.g., from foot switch or PLC).

The rear panel shows the 'XS-1' control port and the 'AC 100-240V 50/60Hz FUSE:2AMP 250VAC' power connector.

5.2 Button and Display Instruction

5.2.1 Button Instruction

• Power Switch: Power On/Off.
• Arrow Buttons (Up/Down): Edit settings.
• SET Button: Confirm or enter menu.

5.2.2 Display Instruction

• Intensity %: Displays intensity data information.
• Time S: Displays time data information.

5.3 Operating

5.3.1 Startup

5.3.2 Starting Controller

After installation, plug in the power cable and press the Power button. The red LED indicator light inside the power button will illuminate when the unit is powered.

5.3.3 Working Mode

Once the LED head is plugged in, the controller automatically enters Working Mode.

5.4 Parameter Setting

5.4.1 Intensity Setting

1. Enter working mode.
2. Press and hold the Up arrow button [▲] to set intensity. The intensity data will flash when the button is pressed and stop flashing when released.
3. Use the Up arrow [▲] or Down arrow [▼] button to adjust the intensity.
4. Press the SET button twice to confirm and save the setting.

5.4.2 Time Setting

1. Enter working mode.
2. Press and hold the Down arrow button [▼] to edit the time. The time data will flash.
3. Use the Up arrow [▲] or Down arrow [▼] button to change the time value.
4. Press the SET button to confirm and move to the next setting unit.
5. Press the SET button twice to confirm and save when finished with the last setting.

5.5 Working Mode Setting

In Working Mode, you can switch between Manual and Timer modes by holding the SET button. In Timed Mode, the set time is displayed. In Manual mode, 'oFF' is displayed under 'Time S'.

5.6 Working Temperature

Press the SET button once while in working mode to display the temperature of the LED head.

5.7 LED Head Unit and Foot Switch

Diagram showing a foot switch connected to the controller. Pressing the foot switch activates the LED head according to the set parameters.

6 Shutdown

Step 1: Press the Power button to turn off the controller. The red indicator light will turn off simultaneously.

Step 2: Disconnect the power cable.

Diagrams illustrate the Power button on the front panel and the rear panel connectors (XS-1 and power input) for shutdown procedures.

7 Troubleshooting

8 Replacement Parts

9 WARRANTY

Henkel expressly warrants that all products referred to in this Instruction Manual for Loctite® CL10 Single LED Controller (hereafter called “Products”) shall be free from defects in materials and workmanship. Liability for Henkel shall be limited, as its option, to replacing those Products which are shown to be defective in either materials or workmanship or to credit the purchaser the amount of the purchase price thereof (plus freight and insurance charges paid therefore by the user). The purchaser’s sole and exclusive remedy for breach of warranty shall be such replacement or credit.

A claim of defect in materials or workmanship in any Products shall be allowed only when it is submitted in writing within one month after discovery of the defect or after the time the defect should reasonably have been discovered and in any event, within (12) months after the delivery of the Products to the purchaser. This warranty does not apply to perishable items, such as (indicate items: fuses, filters, lights, etc.). No such claim shall be allowed in respect of products which have been neglected or improperly stored, transported, handled, installed, connected, operated, used or maintained. In the event of unauthorized modification of the Products including, where products, parts or attachments for use in connection with the Products are available from Henkel, the use of products, parts or attachments which are not manufactured by Henkel, no claim shall be allowed.

No Products shall be returned to Henkel for any reason without prior written approval from Henkel. Products shall be returned freight prepaid, in accordance with instructions from Henkel.

NO WARRANTY IS EXTENDED TO ANY EQUIPMENT WHICH HAS BEEN ALTERED, MISUSED, NEGLECTED, OR DAMAGED BY ACCIDENT.

EXCEPT FOR THE EXPRESS WARRANTY CONTAINED IN THIS SECTION, HENKEL MAKES NO WARRANTY OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCTS.

ALL WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND OTHER WARRANTIES OF WHATEVER KIND (INCLUDING AGAINST PATENT OR TRADEMARK INFRINGEMENT) ARE HEREBY DISCLAIMED BY HENKEL AND WAIVED BY THE PURCHASER.

THIS SECTION SETS FORTH EXCLUSIVELY ALL OF LIABILITY FOR HENKEL TO THE PURCHASER IN CONTRACT, IN TORT OR OTHERWISE IN THE EVENT OF DEFECTIVE PRODUCTS.

WITHOUT LIMITATION OF THE FOREGOING, TO THE FULLEST EXTENT POSSIBLE UNDER APPLICABLE LAWS, HENKEL EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY IN CONNECTION WITH THE SALE OR USE OF, OR OTHERWISE IN CONNECTION WITH, THE PRODUCTS, INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS AND SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER CAUSED BY NEGLIGENCE FROM HENKEL OR OTHERWISE.