Product Specifications
| Model No. | Name | Material | Colour | IP Rating | Input Voltage | Lamp Base | Lamp Wattage | Colour Temp | Lumens | CRI | Wiring | Dimmable | Warranty |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| HV1608T-BLK-12V HV1608T-SS316-12V HV1618T-BLK-12V HV1618T-SS316-12V |
Maxi 900 | 316 Stainless Steel | Black / Stainless Steel | IP54 | 12v DC | MR16 | 1x 5w | TRI Colour - 3000k, 4000k, 5500k | 270lm, 285lm, 300lm | > 80 | Parallel | No | 2 Years Replacement* |
| HV1608T-BLK-240V HV1608T-SS316-240V HV1618T-BLK-240V HV1618T-SS316-240V HV1615T-SS316-240V |
Maxi 900 | 316 Stainless Steel | Black / Stainless Steel | IP54 | 240v AC | E27 | 1x 9w | TRI Colour - 3000k, 4000k, 5500k | 700lm, 720lm, 740lm | > 80 | Parallel | No | 2 Years Replacement* |
Dimensions
Mounting Base: Diagram shows a circular base with four mounting holes (6mm diameter) and a central opening. Key dimensions provided are 98mm outer diameter, 70mm inner diameter, and a radius of 35mm.
Bollard Dimensions: Diagrams show the overall dimensions of the bollard lights. Both the HV1608 and HV1618 models are depicted with a height of approximately 900mm and a diameter of approximately 102mm.
Important Safety Issues
- This product must be installed by a qualified electrician according to AS/NZS 3000.
- Ensure all electrical mains are disconnected before any installation.
- Do not exceed maximum wattage restrictions for globes: 240V GU10 = 35w / 12V MR16 = 20w.
- Modification of this product will void any warranty.
- Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
- When installing low voltage fittings, voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver; if not within this allowance, warranty will be voided.
- Aluminium and 304SS fittings must not be installed within 2km of any salt water environments.
- When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting.
- All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining)
- When installing surface mounted bollards, base plate must be installed on concrete or concrete pad. Fitting should not be installed under ground level. All holes including cable entry must be siliconed to prevent any water penetration into fitting; silicon must also be applied around fitting at ground level. Failure to do this will void warranty.
- All o-rings and seals must be in place correctly to maintain warranty.
- These instructions may be updated at any time due to product improvements; please visit the website for the most current installation instructions.
Steps for Installation
- Make sure that the electrical circuit is free of voltage (master switch off).
- Remove 4x allen screws from the side of fitting and put aside.
- Install baseplate in the desired location using appropriate screws for the application. The screws supplied are mild steel and must be replaced with a higher grade if there is any chance of them being affected by water. The location of the baseplate must be installed on either concrete or a concrete base and cannot be installed under ground level.
- Locate the IP rated junction box within the fitting. Undo screws from the junction box and remove the cover.
- Insert the cable through the cable gland on the junction box. If your cable is not circular, you must fix the entry of your cable to maintain the IP rating. Failure to do so will void warranty.
- Using an appropriate 12V DC LED driver - DO NOT CONNECT FITTING DIRECTLY TO 240V.
- Connect live and neutral wires. If more than one fitting is installed, wiring must be done in parallel.
- Reattach the cover to the IP rated junction box, making sure screws are tight and seals are still in place.
- Apply silicone to all cable entry holes and fixing points on the baseplate to avoid moisture penetration into the fitting.
- Place the bollard onto the base plate and reattach the 4x allen screws set aside earlier.
- Colour temperature is set to 3000K. To change, remove the cover from the fitting by twisting anti-clockwise. For HV1608 models, remove the 2x nuts and washers and put aside. Remove the globe by also twisting anti-clockwise and select the desired colour temperature by moving the switch on the side of the globe, then reinsert the globe.
- Reattach the cover by turning clockwise, or for HV1608 Models, reattach the 2x nuts first, making sure the seals are still in place and the cover is tight to avoid any water penetration.
- All connections must be carried out carefully; inspect all contacts before switching back on the electric circuit.
Steps for Changing Globe
- Remove the cover from the fitting by twisting anti-clockwise. For HV1608 models, remove the 2x nuts and washers and put aside. Remove the globe by also twisting anti-clockwise.
- Re-insert the appropriate globe by twisting clockwise into the lamp holder (Make sure not to exceed max wattage; see product label for correct info).
- Reattach the cover by turning clockwise, or for HV1608 Models, reattach the 2x nuts first, making sure the seals are still in place and the cover is tight to avoid any water penetration.
Contact Details
Address:
143 Beauchamp Road
Matraville NSW 2036
Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au
Web: www.havit.com.au
Note: This product must be installed by a licensed electrician.
Warranty: Refer to Warranty Terms & Conditions for details.
Havit Lighting
