Allen + Roth Wall Lantern

Care and Maintenance

Shut off the main power supply before performing any maintenance. Periodically clean the fixture using a mild, non-abrasive glass cleaner and a soft cloth. Avoid using solvents or cleaners with abrasive agents, and do not spray liquid cleaner directly onto the bulb or wiring.

Customer Support

For questions, problems, or missing parts, please contact Allen + Roth customer service at 866-439-9800 (8 a.m. - 8 p.m., EST, Monday-Sunday) or ascs@lowes.com.

For more information, visit Lowes.com, search the item number (0398463), and refer to the Guides & Documents tab on the product's page.

Safety Information

General Warnings

• Ensure the electrical system has proper grounding. Failure to do so could result in electrical shock if wires become damaged.
• Do not suspend the fixture by the supply wires or wire connectors, as this could cause the fixture to fall, leading to injury or fire hazards.

Cautions

• Do not use bulbs with a wattage exceeding the maximum specified on the fixture to prevent overheating and fire risks.
• Ensure all electrical connections comply with local codes, ordinances, and the National Electrical Code (ANSI/NFPA 70-199). Consult a qualified electrician if you are unfamiliar with electrical wiring.
• Turn off electricity at the main fuse or circuit breaker box before starting installation.
• Mount all fixtures to an outlet box supported by the building structure. Do not rely on drywall alone to support the fixture.
• Do not connect the fixture's ground wire (green or bare) to the black (hot) or white (neutral) supply wires.
• Do not connect this fixture to an electrical system that lacks equipment grounding.

Warranty

Allen + Roth warrants this lighting fixture against defects in materials and workmanship for three (3) years from the date of purchase. If the product is found to be defective within this period, present a copy of the bill of sale and the product in its original carton to the place of purchase. The manufacturer will, at its option, repair, replace, or refund the purchase price. The consumer is responsible for all installation and removal costs. This warranty does not cover defects due to misuse, accidental damage, improper handling, or installation. It specifically excludes liability for direct, incidental, or consequential damages. Some states may not allow these exclusions, so they may not apply to you. This warranty grants specific rights, and you may have other rights that vary by state.

Installation Overview

Preparation

Before assembly, verify all parts are present by comparing them with the package contents and hardware lists. Do not assemble if parts are missing or damaged.

Estimated Assembly Time: 35 minutes

Tools Required (Not Included)

• Screwdriver
• Wire strippers
• Pliers
• Voltage tester

Helpful Tools (Not Included)

• Ladder

Package Contents

• A: Mounting Bracket
• B: Fixture
• C: Fixture Arm
• D: Fixture Body

Hardware Contents

• AA: Screws (x3)
• RR: Screws (x2)

Step-by-Step Installation

1. Turn off the electrical power at the main fuse or circuit breaker.
2. Mount the mounting bracket (A) to the outlet box using the provided screws (AA).
3. Feed the fixture wires through the center hole of the mounting bracket.
4. Loosen the ground screw on the mounting bracket (A). Wrap the bare wire from the fixture (D) around the ground screw and tighten it.
5. Connect the wires: Connect the black fixture wire to the black (hot) supply wire. Connect the white fixture wire to the white (neutral) supply wire. Connect the fixture's bare ground wire to the supply ground wire. If supply wire colors differ, consult a professional electrician.
6. Attach the fixture (B) to the mounting bracket (A) using the provided screws (RR). Note: The position of the short screws (RR) will determine the orientation of the fixture (D).
7. If the fixture is not secure, adjust the hex nut preassembled on the threaded rod of the mounting bracket.
8. Install a bulb (sold separately). Use a 100W maximum medium-base incandescent bulb or CFL equivalent.
9. Apply silicone sealant (not included) around the fixture base where it meets the wall for weatherproofing.
10. Restore power at the main fuse or circuit breaker.