LED Wash Light KL-4015

Content Overview

• Safety warning instructions
• Installation
• Signal and power connection
• Function setting
• DMX address setting
• Operation menu
• DMX Channel
• Maintenance
• Trouble shooting
• Technical data

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice.

Accessories

Safety Warning Information

After receiving the lights, please open to check whether there is any damage caused by transportation. In case of damages caused by transportation, please do not use this device and contact your dealer or manufacturer as soon as possible.

The projector is for indoor and outdoor use, IP65.

Do not install the fixtures onto inflammable surfaces directly. [no-flammable-surfaces-symbol]

The fixture is only intended for installation, operation and maintenance by qualified personnel.

Do not project the beam onto inflammable surfaces; minimum distance is 3 meters.

Avoid direct exposure to the light from the lamp. The light is harmful to the eyes.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the fixture.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be attached as shown in the “Installing the projector” section.

Shields and lens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired, for example by cracks or deep scratches.

Exterior surface temperatures of the luminaire after 5 minutes operation is 45°C; when steady state is achieved, it is 70°C. There are no user-serviceable parts inside the projector; do not open the housing and never operate the fixture with the covers removed.

There are no user-serviceable parts inside this light; please check whether all covers or shells have been installed and screws have been tightened securely. It is forbidden to use lights with covers (or shell) open.

If you have any questions, don't hesitate to consult your dealer or manufacturer.

Installation

Always disconnect from power before the device's installation, cleaning, and maintenance.

Diagram Description: The diagram shows the LED Wash Light fixture. Labels indicate:

• "Safety Chain/cord Attachment Point" on the top.
• "Safety Cord" connected to this point.
• "Quik Lock" points on the top and sides, with associated knobs.

Take out 2 clamps and 1 safety rope. Install the 2 clamps on the bottom of the fixture with the 4 quick knobs attached to the clamps. Then, hang the fixture on the fixed support with the clamp, and tighten the clamp lock bolt to fix the fixture. Please confirm that the fixture installation is stable and reliable, and ensure that the hoisting position has sufficient strength to withstand the weight of the fixture. Carry the randomly equipped safety rope through the bottom of the fixture holder for auxiliary hoisting to ensure safety.

Warnings:

1. The clamps are only used when installing the fixtures. It is strictly forbidden to use the clamps as a handle to carry the fixtures.
2. For safety reasons, please use a safety rope that can withstand 10 times the weight of the fixture through the safety hole of the fixture body.
3. Side hanging the fixtures is forbidden.

Signal and Power Connect

Diagram Description: The diagram illustrates DMX signal connections. It shows:

• A 3-pin XLR connector labeled "DMX OUT" with pins 1, 2, and 3.
• A 3-pin XLR connector labeled "DMX IN" with pins 1, 2, and 3.
• A DMX512 pinout table: PIN 1: FUNCTION GND, PIN 2: FUNCTION DATA-, PIN 3: FUNCTION DATA+.

For the connection of control signals, 2-pin shielded cables with a diameter not less than 0.5 mm must be used between the fixture and the controller and between the fixtures. Please use the 3-pin signal output / incoming line of the lamp to connect. The connections between the 3-pin signal line ports are shown in the figure above. It must be noted that pin 3 of the XLR plug / socket must not be in contact with the inner shell or between the cores when connecting. The XLR plug / socket and the XLR control cable cannot be connected in any other way than the connection shown in the figure above. This product receives the international standard DMX512 (1990) control signal.

For the signal connection of multiple fixtures, the maximum number of connections is 32 fixtures. Use a 3-pin signal cable from the DMX output port of the controller to the DMX input line of the 1st fixture, and connect from the DMX output line of the first fixture to the DMX input line of the second fixture, and so on, until all the fixtures are connected.

When the first fixture is not connected to the controller (the signal line connection between the other fixtures remains unchanged), it is the connection mode of master-slave synchronous control. However, to achieve master-slave synchronization control, the first fixture should be set as the master in the menu, and the remaining fixtures should be set as slaves (the default value is slave).

When connecting the power supply, the power supply of each fixture should be connected separately. Please note that the power supply voltage and frequency must match the power supply voltage and frequency listed in the product manual.

Function and Installation

Use the [UP] or [DOWN] button to browse through the various Setup Options. Press the [ENTER] button to save your settings or enter the next menu. Press the [UP] or [DOWN] button to shift. Press the [Menu] button to return to the upper menu one by one.

DMX Address Setting

When using the controller to control multiple fixtures, each fixture shall be provided with a DMX address to receive signals from the controller and respond correctly. There are 3 control modes in this product: simple mode, standard mode, and extended mode.

For example: The fixture has 20 channels at standard mode. We set the 1st fixture DMX Address to 001, then the 2nd fixture DMX Address to 021, the 3rd fixture DMX Address to 041, the 4th fixture to 61, and so on.

To set the DMX address:

1. Turn on the fixture. If the operating menu is locked, press [ENTER] for 5 seconds; the fixture will be unlocked.
2. Then press [Menu] or [UP] or [DOWN] to find the "AddR" menu.
3. Press [ENTER] to display the DMX Address.
4. Press [UP] / [DOWN] to set the DMX Address value.
5. Press [ENTER] to confirm. The fixture automatically saves this DMX address.
6. Press [Menu] to return to the upper menu.

Operation Menu

Remarks:

1. Only one fixture can be set to host in one signal line; remove DMX control signal when using the host function.
2. In the synchronous control of multiple fixtures, parameters can be transmitted from the master, including: DMX mode, display setting, operation mode (user memory data included). All fixtures accepting parameters will automatically be set to slave mode.

DMX Channel List

4 Channel

8 Channel

Channel priority: dimming > built-in program call > user program call > ARGBW dimming > HSV dimming > Macro Instruction > Color Temperature

Maintenance

To ensure the reliability of the projector, it should be kept clean. It is recommended that the fans should be cleaned every 15 days. The lens and dichroic color filters should also be regularly cleaned to maintain optimum light output. Do NOT use any type of solvent on dichroic color filters.

Cleaning frequency depends on the environment in which the fixture operates: damp, smoke, or particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics. A soft cloth and typical glass cleaning products should be used for cleaning. It is recommended to clean the external optics at least once every 20 days and clean the internal optics at least once every 30/60 days.

Do not use any organic solvent, e.g. alcohol, to clean the reflector mirror, dichroic color filters, or housing of the apparatus.

Troubleshooting

Technical Data

Input voltage: AC 100V/120V/200V/220V/230V/240V 50/60Hz

Power: 600W@220V

LED light source: 40PCS 15W RGBW

Working lifetime: 50000h

Effect: Control in 4 segments, Variable Speed Two-way Rainbow Effect, Color Flow Effect

Dimmer: 0-100% linear dimming

Strobe: Electric strobe, 0.3-20pcs/sec, Max 20 Hz

Control mode: International standard DMX 512 signal, 3 Pin (5 Pin) DMX512 interface RDM, Wireless: 2.4 GHz W-DMX™ (optional)

Modes: 2 channel modes, Master-slave, Stand-alone mode, Self-test mode

Other functions: Adjustable horizontal and vertical speed, Display fixture using time, Display software version number, Modular structure for easy maintenance, Speed-regulating radiator

Shell and protection level: High-strength casting aluminum alloy, IP65, black shell (white optional)

Working temperature: -20°C ~ 40°C

Weight: 14.8Kg

Produce size: See below

Product Dimensions

Diagram Description: The diagram shows three views of the LED Wash Light KL-4015:

• Top View: Shows the width of 530mm and the control panel with four buttons and an LCD screen.
• Front View: Shows the width of 470mm, the height of 357mm, and the array of 40 LED lights.
• Side View: Shows the depth of 172mm and the fixture's profile with the mounting bracket.