Vaxcel T0750 / T0751 Assembly and Installation Instructions

WARNING

Turn off the main power at circuit breaker before installing fixture.

AVERTISSEMENT: Coupez la source d'alimentation principale au panneau central de disjoncteurs avant d'installer le luminaire.

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions.

Hardware Package (included):

• Crossbar Unit (A)
• Mounting Screw (B)
• Wire Connector (C)
• Bolt Nut (D)
• Rubber Pad (E)

A diagram shows the hardware components with their respective labels.

Installation Steps

Step 1: Turn off the power at fuse or circuit box.

Step 2: Unscrew the two bolt nuts (D), remove the two rubber pads (E) and the crossbar unit (A) from the backplate.

Step 3: Attach the crossbar unit (A) to the outlet box by using two mounting screws (B). Adjust the length of the preinstalled fixture mounting screws if necessary. Ensure that the fixture mounting screws are lined up horizontally to make the fixture level.

A diagram illustrates the wiring connections within an outlet box, showing the connection of house ground wire, fixture ground wire, fixture wire, and power source wires using wire connectors. It also shows the crossbar unit attached to the outlet box, the backplate, and the glass shade being secured.

Step 4: Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows:

• Connect the hot wire (black insulation) from the fixture to the black wire from the power source.
• Connect the neutral wire (white insulation) from the fixture to the white wire from the power source.
• Attach the fixture ground wire (bare wire) to the crossbar unit (A) with the green ground screw, then connect it to the house ground wire with the wire connector (C).

Carefully put all of the wires back into the outlet box.

Step 5: Attach the backplate of the fixture to the mounting plate unit (A) by inserting fixture mounting screws into set holes on the backplate, then secure it with two rubber pads (E) and two bolt nuts (D). Caulk completely around where the backplate meets the wall surface to prevent water from seeping into the outlet box.

Step 6: Attach the glass shade to the socket and secure it with the socket ring.

Step 7: Install the bulb (not included). Check relamping label at socket area or packaging for maximum wattage allowed. A maximum 60W Type A bulb is recommended.

Step 8: Turn on the power at fuse or circuit box.

Optional Installation: Disconnect Dusk-to-Dawn Photocell

IMPORTANT: Compatible with dimmer when photocell is disconnected. Requires dimmable bulb and compatible dimmer switch.

Diagrams illustrate the wiring for the photocell and the alternative wiring without the photocell, showing connections between fixture wires, photocell wires, and power source wires using wire connectors.

Step 1: Turn off the power at the fuse or circuit box before starting installation.

Step 2: Loosen the wire connectors connected with the wires from the photocell.

Note: Do not remove the photocell to prevent water from seeping into the outlet box.

Step 3: Take a white pigtail and black pigtail and make wire connections using wire connectors (C):

• The black wire from the fixture to one end of the black pigtail.
• The white wire from the fixture to one end of the white pigtail.
• The other end of the black pigtail to the black wire from the power source.
• The other end of the white pigtail to the white wire from the power source.

Put all wires back into the backplate of the fixture.

Step 4: Turn on the power at fuse or circuit box.

Spare Parts List

The following parts are available for reorder if damaged or missing:

• Crossbar Unit (A)
• Mounting Screw (B)
• Wire Connector (C)
• Bolt Nut (D)
• Rubber Pad (E)
• Mounting Hardware 6805MM (1SET)

A diagram shows the spare parts list and dimensions for models T0750 and T0751:

• T0750: A: 10", B: 9", C: 11"
• T0751: A: 12", B: 9-3/4", C: 13"

5 Year Limited Warranty

Vaxcel warrants all of its products against defects in workmanship and finishes for one year following the date of shipment.

In addition:

• Any product with an integrated motion sensor or dusk-to-dawn photocell is supported by a 5-year warranty for the functionality of the product.
• Any product with integrated LED modules is covered by a 5-year warranty on the LED functionality.

Exclusions: This warranty does not include the failure of products from extreme acts of nature; environmental conditions not suited for the products intended use; operation in temperatures outside of the range specified in the instruction manual, usage with improper power supply, power surges or dips. For coastal locations, some corrosion is considered normal for the environment.

Vaxcel reserves the right to repair, replace or issue a credit for any properly installed product, provided it is returned per RMA instruction. This warranty is limited to the cost of the product only and does not extend to transportation, installation or replacement costs.

How can warranty service be obtained?

info@vaxcel.com

1-800-482-9235