ASSEMBLY AND INSTALLATION INSTRUCTIONS
Model: T0571
Important Safety Information
WARNING: Turn off the main power at circuit breaker before installing fixture.
AVERTISSEMENT: Coupez la source d'alimentation principale au panneau central de disjoncteurs avant d'installer le luminaire.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions.
Hardware Package (included):
- Crossbar Unit (A)
- Mounting Screw (B)
- Wire Connector (C)
- Bolt Nut (D)
- Rubber Pad (E)
- Mounting Hardware (6200MM, 1SET)
- Glass Shade (10148CS)
- Set Screw (6201MM)
Diagram showing the assembly of the fixture, including the outlet box, crossbar unit, fixture mounting screws, ground wires, wire connectors, photocell, backplate, fixture, glass shade, set screw, and metal cover. The diagram also indicates the maximum bulb wattage (Max. 60W Type A Bulb, not included).
Fixture Components and Wiring
Fixture Components:
- Outlet Box
- House Ground Wire
- Wire Connector (C)
- Crossbar Unit (A)
- Fixture Mounting Screw
- Green Ground Screw
- Mounting Screw (B)
- Fixture Ground Wire
- Fixture Wire
- Photocell
- Backplate
- Rubber Pad (E)
- Bolt Nut (D)
- Fixture
- Glass Shade
- Set Screw
- Metal Cover
IMPORTANT: The sensor has an excellent photocell function to enable the light to turn on at dusk and off at dawn automatically.
Installation Steps
- Turn off the power at fuse or circuit box.
- Attach the crossbar unit (A) to the outlet box by using two mounting screws (B). Adjust the length of the preinstalled fixture mounting screws if necessary.
Note: Make sure that the fixture mounting screws are lined up horizontally to make the fixture level. - Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows:
- Connect the hot wire (black insulation) from the fixture to the black wire from the power source.
- Connect the neutral wire (white insulation) from the fixture to the white wire from the power source.
- Attach the fixture ground wire (bare wire) to the crossbar unit (A) with the green ground screw, then depending on local code, connect it to the house ground wire with the wire connector (C).
- Attach the backplate of the fixture to the crossbar unit (A) by inserting fixture mounting screws into open holes on the backplate, then secure it with two rubber pads (E) and two bolt nuts (D).
Note: With silicone caulk compound, caulk completely around where the backplate meets with the wall surface to prevent water from seeping into the outlet box. - Install the bulb (not included). Check relamping label at socket area or packaging for maximum wattage allowed.
- Place the glass shade on the fixture carefully and rotate the glass shade to hold it in place, then attach the metal cover to the fixture by using the two set screws.
- Turn on the power at fuse or circuit box.
Optional Installation: Disconnect Dusk-to-Dawn Photocell
IMPORTANT: Compatible with dimmer when photocell is disconnected. Requires dimmable bulb and compatible dimmer switch.
Diagram Fig.1 shows the photocell wiring with black, white, and red wires from the photocell, and white pigtail wires from the fixture.
Diagram Fig.2 shows the wiring connections for disconnecting the photocell, using wire connectors (C) to connect the fixture's black and white wires to pigtails, which are then connected to the main power source's black and white wires.
- Turn off the power at the fuse or circuit box before starting installation.
- Loosen the wire connectors connected with the wires from photocell. (See Fig.1)
Note: Do not remove the photocell to prevent water from seeping into the outlet box. - Take a white pigtail and black pigtail and make wire connections using wire connectors (C): (See Fig.2)
- a. The black wire from the fixture to one end of the black pigtail.
- b. The white wire from the fixture to one end of the white pigtail.
- c. The other end of the black pigtail to the black wire from the power source.
- d. The other end of the white pigtail to the white wire from the power source.
- Turn on the power at fuse or circuit box.
Spare Parts List
The following parts are available for re-order if damaged or missing.
- Crossbar Unit (A)
- Mounting Screw (B)
- Wire Connector (C)
- Bolt Nut (D)
- Rubber Pad (E)
- Mounting Hardware (6200MM, 1SET)
- Glass Shade (10148CS)
- Set Screw (6201MM)
Diagram showing the dimensions of the fixture: A: 16-3/4", B: 15", C: 23".
5 Year Limited Warranty
Vaxcel warrants all of its products against defects in workmanship and finishes for one year following the date of shipment.
In addition:
- Any product with an integrated motion sensor or dusk-to-dawn photocell is supported by a 5-year warranty for the functionality of the product.
- Any product with integrated LED modules is covered by a 5-year warranty on the LED functionality.
Exclusions: This warranty does not include the failure of products from extreme acts of nature; environmental conditions not suited for the products intended use; operation in temperatures outside of the range specified in the instruction manual, usage with improper power supply, power surges or dips. For coastal locations, some corrosion is considered normal for the environment.
Vaxcel reserves the right to repair, replace or issue a credit for any properly installed product, provided it is returned per RMA instruction. This warranty is limited to the cost of the product only and does not extend to transportation, installation or replacement costs.
How can warranty service be obtained?
Email: info@vaxcel.com
Phone: 1-800-482-9235
