TECNO CM6 User Manual
Exploded Diagram Specification
The following table details the components of the TECNO CM6 smartphone:
| Part Number | Component Name | Part Number | Component Name |
| 1 | TP SP FILM | 2 | TP+LCM |
| 3 | MIDFRAME | 4 | FRONT CAM 50M |
| 5 | VC VAPOR CHAMBER | 6 | FCAM HOLDER |
| 7 | UP SPEAKER | 8 | MAIN BOARD |
| 9 | REAR CAM 50M | 10 | REAR SUPPORT CAM 8M |
| 11 | MAIN PCBA GRAPHITE | 12 | COAXIAL CABLE |
| 13 | FRONT CAM GRAPHITE | 14 | UP FRAME |
| 15 | NFC CABLE | 16 | FLASH FPC |
| 17 | FRONT CAM MYLAR | 18 | FLASHLIGHT FOAM |
| 19 | SUPPORT CAM CONDUCTIVE | 20 | FCAM FOAM |
| 21 | MAIN CAM COPPER | 22 | BACK SENSOR RUBBER |
| 23 | USB FPC FOAM | 24 | MAIN CAM COVER FOAM |
| 25 | BATTERY COVER | 26 | LCM GRAPHITE |
| 27 | USB BOARD | 28 | BATTERY |
| 29 | SIM BOARD | 30 | MOTOR |
| 31 | FINGER | 32 | MAIN SIM FPC |
| 33 | MAIN USB FPC | 34 | LCM RUBBER |
| 35 | DOWN FRAME | 36 | SPK BOX FRAME |
| 37 | FINGER FOAM | 38 | SIM HOLDER |
| 39 | SCREW | 40 | BATTERY COVER DECO |
| 41 | MAIN CAM GLASS LENS | 42 | SUPPORT CAM GLASS LENS |
| 43 | CAM GLASS LENS |
Know Your Phone
This section identifies the key external components of the TECNO CM6:
- 1. Front camera
- 2. Volume + button
- 3. Volume - button
- 4. Power button
- 5. NFC (Near Field Communication)
SIM Card Installation
To install a SIM card:
- Power off your phone.
- Refer to the diagrams for SIM card installation. The phone supports SIM 1 and SIM 2.
Charging the Phone
You can charge your TECNO CM6 using a charger or by connecting it to a computer via a USB cable (included with the phone). It is recommended to use only official TECNO chargers and cables to prevent damage to the phone and preserve the warranty.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:
- (1) This device may not cause harmful interference.
- (2) This device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modifications may void the user's authority to operate the equipment.
Information to the User
This equipment has been tested and found to comply with the limits for a Class B digital device, as per part 15 of the FCC Rules. These limits are intended to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used according to the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a specific installation. If interference is experienced with radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try correcting the interference by:
- Reorienting or relocating the receiving antenna.
- Increasing the separation between the equipment and the receiver.
- Connecting the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consulting the dealer or an experienced radio/TV technician for assistance.
Specific Absorption Rate (SAR) Information
This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed through periodic and thorough evaluation of scientific studies by independent scientific organizations. These standards include a substantial safety margin to ensure the safety of all persons, regardless of age or health.
The SAR limit for the USA (FCC) is 1.6 W/kg, averaged over one gram of tissue. The TECNO CM6 (FCC ID: 2ADYY-CM6) has been tested against this SAR limit. The highest reported SAR value for use at the ear under this standard during product certification is 0.430 W/kg, and when properly worn on the body, it is 0.727W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0cm must be maintained between the user's body and the handset, including the antenna. Third-party belt clips, holsters, and similar accessories used with this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
