Explosion Diagram Specification
Component List
A detailed exploded view of the TECNO KE5K mobile phone's internal components, illustrating the assembly of various parts. The following table lists the identified components:
| Part Number | Description | Part Number | Description |
|---|---|---|---|
| 1 | FL(CTP+LCM) 6.52HD+ KE5 Black HX V1.0 | 2 | Astigmatism film 3.5*1.2*0.05 KE5 |
| 3 | FPC Side key BB4 | 4 | Astigmatism film 3.5*1.2*0.05 KE5 |
| 5 | Shield Seal Cop foil 20.7*15.5 *0.06 KE5 | 6 | LT sensor Seal rubber KE5 Black |
| 7 | F CAM Seal rubber KE5 Black | 8 | FPC REC KC1 |
| 9 | FM(ICNF7332AL)04 Aqua Blue19 fingerchip | 10 | CAM FF 8W GC6153 CSP W6003 XCG V 1.0 |
| 11 | CAM AF 13M S5K3L6 B B 5P B ST V1.0 | 12 | CAM FF 8M GC8034 А В 4Р В TXD V1.0 |
| 13 | F CAM con fb 10.75*7.75*0.1 KE5 | 14 | DistanceSensorSeal mylar10.7*4.8*0.03 KE5 |
| 15 | F LED-Flashseal mylar 8*4.8*0.03 KE5 | 16 | PCBA MB H6123 A1 32GB+2GB V1.0 |
| 17 | REC 1206W H20 broadband H:SPL 50mW Goer | 18 | R MAIN CAM Con foams 12.61*10.46*0.2 KE5 |
| 19 | BATT Seal rubber 6.15*4.0*0.65 KE5 | 20 | LCM Con Seal rubber 13.1*3.7 *0.65 KE5 |
| 21 | R hsg asm KE5 Black PC | 22 | Bat imp steel KE5 |
| 23 | R CAM lens KE5 Glass 0.5mm Black | 24 | mc screw M1.4*L2.5*D2.5 *H0.5 silver glue |
| 25 | Bat cover asm KE5 Aqua Blue PC | 26 | mc screw M1.4*L3.5*D2.5 *H0.5 silver |
| 27 | SPK frame asm KE5 Black PC | 28 | Coaxial cable ECT D 147.9 X653C |
| 29 | Bat TECNO BL 49FT 4900mAh FH IN | 30 | PCBA SUB H6123 1 A V1.0 |
| 31 | FP graphite film 37.14*28.8 *0.05 KE5 | 32 | FP In mylar 4*4*0.05 KE5 |
| 33 | FP support foam 13.26*12.78 *0.6 KE5 | 34 | FP con foams 7.5*3.5*1 KE5 |
| 35 | ZIF mylar 9.5*3.5*0.05 KE5 | 36 | Motor COIN 1027 L22 H JX |
| 37 | SPK 1115 SPR H3.0 aluminiumfilmRoHS Goer | 38 | SUB PCB Con Seal rubber KE5 |
| 39 | FPC SPK KE5 |
Know Your Phone
Front view of the TECNO KE5K smartphone, highlighting the front camera at the top center, the volume keys on the left side, and the power key on the right side.
- 1. Front camera
- 2. Volume key
- 3. Power key
SIM/SD Card Installation
1. Power off mobile.
2. Refer to the following picture for SIM / SD card installation.
Rear view of the TECNO KE5K smartphone's internal frame, indicating the positions for SIM 1 and SIM 2 card slots.
Charging the Phone
You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone).
1. Please remind the front and back of the plug.
2. Use only TECNO charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty.
Illustration of a smartphone being charged via a USB cable, with a close-up view of the charging port.
FCC Caution and SAR Information
Emergency Call
If any emergency arises, dial 112/911 (or other emergency call number) for emergency help. Due to the nature of cellular networking, the success of emergency call is not guaranteed.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types KE5k (FCC ID: 2ADYY-KE5K) has also been tested against this SAR limit.
The highest reported SAR values for head, body-worn accessory, and product specific (Hotspot) are 0.762 W/kg, 0.704 W/kg, and 0.735 W/kg respectively. The Max simultaneous SAR is 1.009 W/kg. This device was tested for typical body-worn operations with the back of the handset kept 10mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
