TECNO POVA Neo 3 User Manual
Explosion Diagram Specification
The following table details the components of the TECNO POVA Neo 3 as shown in the explosion diagram:
| Part No. | Description | Part No. | Description |
|---|---|---|---|
| 1 | TP+LCM | 2 | LIGHT GUIDE FILM |
| 3 | REC DECO | 4 | F HOUSING ASM |
| 5 | MAIN BOARD | 6 | UP SPEAKER |
| 7 | PROXIMITY SENSOR RUBBER | 8 | RECEIVER CONDUCTIVE FABRIC |
| 9 | PCBA COOPER | 10 | R CAM CON FOAM |
| 11 | R CAM CON FB | 12 | CAM AF |
| 13 | CAM FF | 14 | F CAM FRAME |
| 15 | BAT RUBBER | 16 | F CAM |
| 17 | F CAM COOPER | 18 | R CAM RUBBER |
| 19 | R HOUSING ASM | 20 | SCREW L3.5 |
| 21 | SCREW L2.5 | 22 | R CAM FRAME |
| 23 | BATTERY ASM | 24 | CAM DECO |
| 25 | RFLASH LENS | 26 | CARD HOLDER |
| 27 | R CAM LENS 8M | 28 | R CAM LENS 16M |
| 29 | SCREW L2.0 | 30 | WATERPROOF MYLAR |
| 31 | WATERPROOF FRAME | 32 | COAXIAL CABLE |
| 33 | USB RUBBER | 34 | TP BTB RUBBER |
| 35 | SIDEKEY FPC | 36 | EARJACK RUBBER |
| 37 | FINGERPRINT ASM | 38 | DOWN SPK |
| 39 | SUB LCM FPC | 40 | MOTOR |
| 41 | SUB PCB | 42 | SIDEKEY FPC MYLAR |
Know Your Phone
The TECNO POVA Neo 3 has the following key features:
- 1. Front camera: Located on the front of the device.
- 2. Volume + key: Increases the volume.
- 3. Volume - key: Decreases the volume.
- 4. Power key & side fingerprint sensor: Used for powering the device on/off and unlocking it.
- 5. NFC: Near Field Communication capability.
Diagrams illustrating the front and back of the phone with these components labeled are provided.
SIM/SD Card Installation
- Ensure the mobile device is powered off.
- Refer to the provided illustration for the correct procedure for SIM and SD card installation. The illustration shows a SIM tray with slots for SIM 1, SIM 2, and an SD card.
Charging the Phone
The device can be charged using a TECNO charger and USB cable, or by connecting it to a computer via USB cable. Using non-TECNO chargers or cables may damage the device and invalidate the phone's warranty.
Illustrations show the USB port on the phone and a USB cable being connected.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- (1) This device may not cause harmful interference.
- (2) This device must accept any interference received, including interference that may cause undesired operation.
Information to User
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) Information
This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. The TECNO POVA Neo 3 (Model: LH6n, FCC ID: 2ADYY-LH6N) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.27W/kg and when properly worn on the body is 1.18W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
