Holmes Twin Window Fan (HAWF2021/HAWF2021TG)

Safety Instructions

When using electrical appliances, basic safety precautions should always be taken, including:

1. Read all instructions before using this appliance.
2. Use the fan only for purposes described in this manual.
3. To protect against electrical shock, do not immerse the unit, plug, or cord in water or spray with liquids. Plug the appliance directly into a 120V AC electrical outlet.
4. Close supervision is necessary when any appliance is used by or near children.
5. Unplug from the outlet when not in use, when moving the fan, before putting on or taking off parts, and before cleaning.
6. Avoid contact with moving parts.
7. Do not operate in the presence of explosive and/or flammable fumes.
8. To avoid fire hazard, NEVER place the cord under rugs or near an open flame, cooking, or other heating appliances.
9. Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or has been dropped/damaged. Discard the fan or return it to an authorized service facility for examination and/or repair.
10. Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not route the cord under furniture or appliances. Arrange the cord away from traffic areas and where it will not be tripped over.
11. The use of attachments not recommended or sold by the appliance manufacturer may cause hazards.
12. Do not let the cord hang over the edge of a table or counter, come in contact with hot surfaces, or leave it exposed in high-traffic areas.
13. Do not use outdoors.
14. To disconnect, grip the plug and pull from the wall outlet. Never yank on the cord.
15. Always use on a dry, level surface.
16. Do not operate the fan until fully assembled with all parts properly in place.
17. This product is intended for household use ONLY and not for commercial or industrial applications.
18. WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
19. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.

Polarized Plug Warning: This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not attempt to modify this plug or defeat this safety feature in any way.

Storage and Accessories

Fan Storage

For all window fans, and fans that come already assembled:

• It is important to keep it in a safe, dry location.
• We recommend using the original (or appropriately sized) box.
• Please remember to protect the fan from dust or moisture.

Window Fan Accessories

An extender panel is available for window fans. To order, please visit www.holmesproducts.com.

For questions regarding your product or other Holmes® products, please visit www.holmesproducts.com. For inquiries regarding recycling and proper disposal, please contact your local waste management facility.

Warranty Information

1 YEAR LIMITED WARRANTY

Sunbeam Products, Inc. doing business as Jarden Consumer Solutions (or Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions in Canada) warrants this product for a period of one year from the date of purchase against defects in material and workmanship. JCS will, at its option, repair or replace this product or any component found to be defective. Replacements will be made with new or remanufactured products or components. If the product is no longer available, a similar product of equal or greater value may be provided.

This warranty is exclusive and does not cover normal wear, damage from misuse, use on improper voltage, or unauthorized repairs or alterations. It also does not cover Acts of God.

JCS shall not be liable for any incidental or consequential damages. Any implied warranty of merchantability or fitness for a particular purpose is limited to the duration of this warranty. This warranty gives you specific legal rights, which may vary by province, state, or jurisdiction.

How to Obtain Warranty Service:

In the U.S.A. and Canada, visit www.holmesproducts.com or write to ATTN: Holmes, Jarden Consumer Solutions, PO Box 3900, Peoria IL 61614. Please do not return the product to this address or the place of purchase.

Installation Instructions

Carefully unpack all contents. Ensure all parts are present.

The window fan comes fully assembled and ready for installation.

Key Components (Refer to Figure 1):

• A. Slide-on Extender: 4.25 inches (10cm)
• B. Top Window Support
• C. 2-Speed Motor Control
• D. Built-in Adjustable Extender Panel: Pulls out up to 7 inches (17cm)

For Double-Hung Windows:

This fan is designed for double-hung windows with minimum openings of 22 inches (55cm) wide and 10 inches (25cm) high.

1. Align the fan horizontally in the window with the built-in extender panel (D) to the right.
2. Measure the window opening accurately.
3. Use the installation guide below to determine the required extender panel(s).
4. Attach any necessary extender panels. Set the fan in the window. Pull out the built-in extender (D) to fit the opening. Push the clips down to lock it in place.
5. Carefully close the window onto the top of the fan so the bottom edge of the window rests behind the top line of the fan housing. This helps secure the fan.

Installation Guide Summary:

• For 22 to 29 inches (55-73cm): Use up to 7 inches (17cm) of the right-side built-in extender panel.
• For 29 to 33.25 inches (73-83cm): Use one 4.25 inch (10cm) extender panel (A) on the left side. Adjust the right-side built-in extender (D) for a tight fit (0.5 to 7 inches / 1-17cm).
• For openings larger than 33.25 inches (83cm): Additional extender panels are required (see Window Fan Accessory Section).

For Slider Windows:

The fan fits windows 10 inches (25cm) wide and 36 inches (91cm) high. Ensure the control faces inward. The 7-inch (17cm) built-in extender (D) will be positioned on top. Measure the window height and adjust the upper extender for a snug fit. You may need to remove the window screen.

Diagram Description (Figure 2): The front view shows the unit's length of 22 inches (55cm). The left side can accommodate a 4.25-inch (10cm) extender panel, while the right side has a built-in extender that pulls out up to 7 inches (17cm).

Operating Instructions

• Ensure the rotary switch (C) is in the OFF position.
• Plug the fan into a 120V AC electric outlet.
• To use in EXHAUST mode, manually turn the unit around in the window. Controls can be operated from either side.
• To start the unit, turn the rotary switch (C) to the desired speed (High or Low).

WARNING: Be sure the fan is securely installed in your window at all times. Do not lean or push on the fan while it is in the window.

Cleaning and Maintenance

Follow these instructions to correctly and safely care for your window fan.

Fuse Replacement

If your 5 Amp, 125 Volt replaceable fuse blows, visit www.holmesproducts.com for information on ordering a new fuse. Follow these instructions to replace the fuse on the plug:

1. Unplug the fan. Grasp the plug and remove it from the outlet. Do not unplug by pulling on the cord.
2. Open the fuse cover, located on the top of the plug, by using your thumb or a flathead screwdriver to slide the cover down towards the prongs. Ensure the cover is completely open before removing the fuse.
3. Carefully remove the fuse using a small screwdriver to pry it out of the compartment by its metal ends.
4. Place the plug on a solid, flat surface. Insert a new 5 Amp, 125 Volt fuse into the compartment and use a small screwdriver to secure the metal ends. Caution: Risk of fire. Replace fuse only with a 5 Amp, 125 Volt fuse.
5. Slide the fuse cover closed completely. If difficult, ensure the fuse is fully seated.
6. Risk of fire: Do not replace the attachment plug. It contains a safety device (fuse) that should not be removed. Discard the product if the attachment plug is damaged.

Diagram Description (Figure 3): The diagram shows the fuse compartment cover on the plug, the fuse itself, and its metal ends, illustrating the fuse replacement process.

Fan Cleaning

• Always unplug the fan before cleaning or disassembling.
• Do not allow water to drip on or enter the fan motor housing.
• Use a soft cloth moistened with a mild soap solution.
• Do not use gasoline, thinner, or benzene as cleaners.

Fan Blade and Front Grill Cleaning

1. Ensure the fan is unplugged.
2. Using a Phillips head screwdriver, remove the screws holding the front and rear grills together. Carefully separate the grills from the end opposite the built-in extender, but do not detach them completely to avoid damaging extender clips. Separate just enough to access the blades.
3. Clean the blades and grills with a soft, moist cloth.
4. Securely fasten the grills back together.