Product End of Life Instructions
VARIABLE SPEED DRIVE ATV630 IP55 5,5KW 400/480V DISCONNECT SWITCH
Altivar Process ATV600/900
Introduction and Scope
This product family is in the scope of European Union directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE). The product family must be disposed according to the legislation of the country. This document is intended for use by end-of-life recyclers or treatment facilities. It provides basic information to assure appropriate end-of-life treatment for the components and materials of the product.
This document is intended for use by professional end-of-life recyclers or waste treatment facilities. It provides basic information for proper end-of-life treatment of product components and materials.
Legal information:
Purpose: As described above.
In case of special transportation: No special transportation.
Recyclability potential: 83% (Based on "ECO'DEEE recyclability and recoverability calculation method" (version V1, 20 Sep. 2008 presented to the French Agency for Environment and Energy Management: ADEME)).
Safety Information
The information provided in this document assumes that the product is completely de-energized and uninstalled (refer to the instructions provided in the appropriate product manuals).
Dismantling/disassembling the product may entail hazards caused by, for example, sharp edges, chemical aggression, or ejected parts.
⚠️ WARNING: HAZARD DUE TO INSUFFICIENT PROTECTION
- Implement all safety measures required by the applicable regulations and by the processes used to dismantle/disassemble and dispose of the product.
- Use all necessary personal protective equipment such as gloves and goggles.
Failure to follow these instructions can result in death or serious injury.
Component Breakdown and End-of-Life Recommendations
The following table details the components of the Altivar Process ATV600/900 series, their identification on the drawings, material, weight, and end-of-life recommendations.
Note: A coin battery is located inside some components.
| Recommendation | Number on Drawing | Component / Material | Weight (in g) | Comment |
|---|---|---|---|---|
| To be depolluted | 1 | Electronic Board (Power and Communication) > 10cm² | 781 | |
| To be depolluted | 2 | LCD and all those back-lighted with gas discharge lamps | 25 | |
| To be depolluted | 3 | Other battery | 2.9 | Lithium content: 0.07 g |
| To be depolluted | 4 | Cable (high current) | 405 | |
| To be depolluted | 5 | Electrolyte capacitors which size: height > 25 mm, diameter > 25 mm or proportionately similar volume | 175 | |
| To be dismantled | 6 | Steel | 5240 | Bar, Ground plate, Support |
| To be dismantled | 7 | Aluminium | 498 | Heatsink |
| To be dismantled | 8 | PC, ABS-PC, PA, PA6, HDPE, SAN with or without additive, PP+EPDM and PP | 4219 | Housing, Chassis, cover |
| Other | 9 | Copper | 1089.1 | Bar |
Diagram Descriptions:
The following descriptions interpret the exploded view diagrams, referencing the numbered components from the table above.
Page 3 Diagram Description:
This diagram shows an exploded view of the variable speed drive. Red arrows indicate components or sub-assemblies for disassembly, while green arrows indicate components or sub-assemblies for assembly or structural elements.
- 1 (Red Arrow): Points to the main Electronic Board (Power and Communication) (Component 1).
- 2 (Red Arrow): Points to the front panel assembly, likely containing the LCD (Component 2).
- 3 (Red Arrow): Points to internal batteries (Component 3).
- 4 (Red Arrow): Points to high-current cabling (Component 4).
- 5 (Red Arrow): Points to electrolyte capacitors (Component 5).
- 6 (Green Arrow): Points to structural elements made of Steel, such as bars, ground plates, or supports (Component 6).
- 7 (Green Arrow): Points to heatsink components made of Aluminium (Component 7).
- 8 (Green Arrow): Points to outer casing, chassis, or cover parts made of PC, ABS-PC, PA, etc. (Component 8).
- 9 (Green Arrow): Points to copper bars or internal wiring (Component 9).
Note: Specific sub-assemblies are indicated by the arrows, and further details are provided on the next page.
Page 4 Diagram Description:
This diagram provides a more detailed exploded view of the internal components of the drive.
- 1 (Red Arrow): Indicates various electronic boards (Component 1) and electrolyte capacitors (Component 5).
- 4 (Red Arrow): Highlights internal ribbon cables (Component 4).
- 5 (Red Arrow): Specifically points to electrolyte capacitors (Component 5).
- 6 (Green Arrow): Shows mounting plates or brackets (Component 6).
- 7 (Green Arrow): Indicates Aluminium heatsink assemblies (Component 7).
- 8 (Green Arrow): Points to internal structural components, chassis, or covers (Component 8).
Product Description
Manufacturer identification: Schneider Electric Industries SAS
Brand name: Schneider Electric
Representative product: VARIABLE SPEED DRIVE ATV630 IP55 5,5KW 400/480V DISCONNECT SWITCH - ATV650U55N4E
Product function: The main function of the Altivar Process product range is the speed control and variation of a synchronous, asynchronous, or reluctance electric motor for fluid management and industrial applications.
Description of the range: This range consists of products Altivar 650 and Altivar 950 with ratings from 0.75 to 11 kW for operation on 400V/480V, 3-phase supplies, IP55 protection rating.
Total representative product mass: 12460 g
Representative product dimensions: 678 mm x 264 mm x 300 mm
Accessories: No accessories needed.
Date of information release: 11/2021
Contact Information
Schneider Electric Industries SAS
Country Customer Care Center
http://www.schneider-electric.com/contact
35 rue Joseph Monier
CS 30323
FR 92500 Rueil Malmaison
RCS Nanterre 954 503 439
Capital social 896 313 776 €
Website: www.schneider-electric.com
Published by Schneider Electric
© 2021 - Schneider Electric - All rights reserved
