USER MANUAL [plus symbol]

FEATURES

• ✔️ 4 smart sensors in 1 compact device
• ✔️ 7 levels of motion sensitivity
• ✔️ 3 modes for motion / temperature LED indicator notifications
• ✔️ Built-in tamper protection
• ✔️ Low battery alerts
• ✔️ New 700 series Z-Wave chip: faster signal and longer battery life
• ✔️ S2 Authenticated security with encrypted communication
• ✔️ SmartStart inclusion for easy and secure pairing

SPECIFICATIONS

Z-WAVE CONTROL

1. Insert the battery.
2. Place the sensor near the location where it will be mounted.

ADD DEVICE to your hub

Initiate inclusion (pairing) in the app (or web interface).

Finalize inclusion at the sensor. Scan the QR code or enter the PIN located under the back cover if your hub supports SmartStart.

Action: Click Z-Wave button once.

The LED indicator will blink red to signal communication and green once the PIN is entered, then turn off to confirm inclusion.

Note: Flip the page for QR codes with step-by-step instructions for adding the sensor to SmartThings, Vera, and Hubitat.

Accessing Z-Wave Button: Use a paperclip [paperclip] to access the Z-Wave button for inclusion, exclusion, reset, and manual wake-up.

TROUBLESHOOTING

The sensor won't add to your system? Try this:

1. Initiate EXCLUSION and click the Z-Wave button on the sensor once.
2. Make sure the battery cover is closed tightly when adding the sensor.
3. Click the Z-Wave button once every 15 seconds for 2 minutes after the sensor joins the network to keep it awake so it can fully configure.
4. Click the Z-Wave button on the sensor 6-7 times quickly when adding it.
5. Bring the sensor closer to your hub; it may be out of range.
6. Double-check if the battery is inserted correctly.

REMOVE THE SENSOR FROM YOUR HUB

1. Bring the sensor within direct range of your Z-Wave gateway (hub).
2. Put the Z-Wave hub into exclusion mode (contact ask@getzooz.com if unsure).
3. Click the Z-Wave button with a paperclip [paperclip] once (it will blink green).
4. Your hub will confirm exclusion and the device will disappear from your controller's device list.

FACTORY RESET

If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, remove the back cover to trigger the tamper switch.

Press and release the Z-Wave button using a paperclip [paperclip] 10 TIMES quickly (within 10 seconds).

Note: All previously recorded activity and custom settings will be erased from the device's memory.

WAKE-UP MODE

The sensor's wake-up interval is set to 12 hours by default to save battery life. You can change the wake-up interval using your controller's advanced settings if available.

During wake-up, the sensor receives communication from the hub (setting updates or network information). A long wake-up interval will not affect how often the sensor reports motion and other values to your gateway controller.

MANUAL WAKE-UP

Press and release the Z-Wave button once to wake the device up. The LED indicator will flash once (blue or orange).

You may need to wake the sensor up manually if:

1. It doesn't fully configure during set-up (values are not displayed or errors pop up in your hub's interface).
2. You change advanced settings for the sensor and want them to update.

MOUNTING

OPTION 1: MOUNTING BRACKET

Use the 2 screws included in the box to fix the mounting bracket to a flat surface of your choice, at least 7 feet above the ground for best results.

Once the bracket is securely installed, carefully slide the 4-in-1 sensor onto the bracket and position it by tilting it to either side, upwards, or downwards, as shown in the illustrations.

Illustration description: Shows a mounting bracket being screwed to a surface, then the sensor being attached to the bracket and tilted.

OPTION 2: ADHESIVE TAPE

Use the supplied adhesive tape to fix the sensor to a CLEAN flat surface of your choice. Apply the tape as shown in the pictures.

Illustration description: Shows adhesive tape being applied to the back of the sensor, then the sensor being pressed onto a flat surface.

Placement Options: The sensor can be mounted in a corner, on a ceiling, or on a wall.

Indoor Use Only: ⚠️ This sensor may only be used and installed indoors. Outdoor installation will void its warranty.

For best results, mount the sensor within 30 feet from the door and around 7 feet from the ground. The 4-in-1 Sensor will detect motion up to 40 feet depending on mounting location and sensitivity settings.

MOTION DETECTION RANGE

The sensor has a detection angle of 125° and a range of up to 40 feet.

Illustration description: Diagram showing a 125-degree detection angle from the sensor, extending up to 40 feet.

See Advanced Settings for ways to optimize and customize motion detection and activity reports.

WARNING

• ⚠️ This product should be installed indoors upon completion of any building renovations.
• ⚠️ Prior to installation, the device should be stored in a dry, dust-and-mold-proof place.
• ⚠️ Do not install the sensor in a place with direct sun exposure, high temperature, or humidity.
• ⚠️ Keep away from chemicals, water, and dust.
• ⚠️ Ensure the device is never close to any heat source or open flame to prevent fire.
• ⚠️ Ensure the device is connected to an electric power source that does not exceed the maximum load power.
• ⚠️ No part of the device may be replaced or repaired by the user, except for the battery.

ADVANCED SETTINGS

Please refer to your controller's user guide for advanced programming instructions, as they differ slightly for every software. Not sure where to start? Contact us at ask@getzooz.com.

CUSTOMIZE YOUR SENSOR

Temperature Sensor

• Parameter 1: Switch between Fahrenheit and Celsius scale. Values: 0 = Celsius, 1 = Fahrenheit (default). Size: 1 byte dec.
• Parameter 2: Set temperature change to be reported. Values: 1-50 (1 = 0.1 degree, 50 = 5 degrees). Default: 1 degree (value 10). The sensor reports new temperature values when it changes by 1 degree up or down. Size: 1 byte dec.

Humidity Sensor

• Parameter 3: Set humidity percentage change to be reported. Values: 1-50 (1 = 1%, 50 = 50%). Default: 10%. Size: 1 byte dec.

Light Sensor

• Parameter 4: Set light percentage change to be reported. Values: 5-50 (5 = 5%, 50 = 50%). Default: 10%. Size: 1 byte dec.

Motion Sensor

• Parameter 5: Set trigger interval (time before motion is reported again after initial trigger). Values: 15-255 seconds. Default: 15 seconds. Note: A smaller interval increases activity and decreases battery life. Size: 1 byte dec.
• Parameter 6: Adjust PIR sensor sensitivity. Values: 1-7 (1 = very high sensitivity, 7 = very low sensitivity). Default: 3. Size: 1 byte dec.

LED Notifications

The LED indicator will flash whenever you press the Z-Wave button to indicate temperature level and wake-up mode.

How to read LED indicator colors?

• Green = under 60°F
• Blue = 60°-75°F
• Yellow = 75°-83°F
• Purple = 83°-97°F
• Red = over 97°F / motion detected / tamper switch triggered
• Flashing red = low battery

• Parameter 7: Choose between LED indicator modes. Values: 1-3. Default: 3. Size: 1 byte dec.
  • Mode 1 = LED indicator is turned off (no visual notifications).
  • Mode 2 = temperature and motion indicated with flashing light. Flashes every 3 minutes for temperature. Note: Mode 2 will increase activity and decrease battery life.
  • Mode 3 = no indication for temperature, motion indicated with red flashing light.

Tamper Switch

The tamper switch is located to the left of the battery slot. It's activated whenever the sensor's cover is removed while the device is powered up. It will send an alarm notification as scheduled.

ASSOCIATION

Associate your 4-in-1 with other Z-Wave devices for direct communication between them, enabling rules and automations to function even if the hub is down.

The 4-in-1 sensor supports Group 1 with up to five devices for Lifeline communication and Group 2 for basic set reports.

To associate the sensor with other devices, put your Z-Wave controller in Association mode by sending the appropriate command and wake up the sensor by clicking the Z-Wave button with a paperclip [paperclip] once.

REQUIRED COMMAND CLASSES

This device requires the following command classes to be supported and recognized by your Z-Wave controller:

• COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3
• COMMAND_CLASS_ASSOCIATION_V2
• COMMAND_CLASS_MULTICHANNEL_ASSOCIATION_GRP_INFO_V3
• COMMAND_CLASS_APPLICATION_STATUS_V1
• COMMAND_CLASS_BATTERY_V1
• COMMAND_CLASS_CONFIGURATION_V4
• COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1
• COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5
• COMMAND_CLASS_INDICATOR_V3
• COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
• COMMAND_CLASS_NOTIFICATION_V8
• COMMAND_CLASS_POWERLEVEL_V1
• COMMAND_CLASS_SECURITY_V1
• COMMAND_CLASS_SECURITY_2_V1
• COMMAND_CLASS_SENSOR_MULTILEVEL_V11
• COMMAND_CLASS_SUPERVISION_V1
• COMMAND_CLASS_TRANSPORT_SERVICE_V2
• COMMAND_CLASS_VERSION_V3
• COMMAND_CLASS_WAKE_UP_V2
• COMMAND_CLASS_ZWAVEPLUS_INFO_V2

This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase the reliability of the network.

QUICK START GUIDES & RESOURCES

Choose your hub and scan the QR code with your phone's camera. Then click on the link to access step-by-step programming instructions.

How to Add It to My Hub?

Links are provided for SmartThings, Hubitat, and Vera. For detailed instructions, please visit the Zooz support website.

How to Adjust Settings?

Links are provided for SmartThings, Hubitat, and Vera. For detailed instructions, please visit the Zooz support website.

How Does It Work?

Scan to learn more about how the sensor reports humidity, temperature, and other values to the hub and how to get the most out of it. Visit www.support.getzooz.com for more information.

WARRANTY

This product is covered under a 5-year limited warranty. To read the full warranty policy or file a warranty claim, please go to www.getzooz.com/warranty.

QUESTIONS?

Visit our support website: www.support.getzooz.com

Contact us via email: ask@getzooz.com

FCC NOTE

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.

Store indoors when not in use. Suitable for dry locations only. Do not immerse in water. Not for use where directly exposed to water.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in any given installation.

If this equipment causes harmful interference to radio or television reception, the user may try to correct the interference by taking one or more of the following measures:

• Reorient or relocate receiving antenna.
• Increase the separation between equipment and receiver.
• Connect equipment into a separate outlet or circuit from receiver.
• Consult the dealer or an experienced radio/TV technician for additional assistance.

All brand names displayed are trademarks of their respective holders.

© Zooz 2021