LED SPEC-SELECT™ DESIGNER TROFFER

PLEASE FIND A QUALIFIED ELECTRICIAN FOR INSTALLATION. Please read the instructions before you install and use the luminaire.

WARNING, CAUTIONS AND OPERATING INSTRUCTIONS

• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture box and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician.
• For the installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electrical code.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

WARNING: RISK OF FIRE OR ELECTRICAL SHOCK

• Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply or performing any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• All wiring connections should be capped with UL approved wire connectors.

CAUTION: RISK OF INJURY

• Not for use in the following applications; food processing facilities, kitchens, chemical processing plants or stockyards.
• Not for use in areas with poor ventilation or high temperatures.
• Operating temperature: 5~113°F (-15~45°C)
• Suitable for damp locations.

! WARNING - TURN OFF POWER SUPPLY FROM MAIN CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING.

FIELD ADJUSTABLE WATTAGE & CCT

The end users may adjust the color temperature and lumen output, respectively, by the two slide switches integrated into the driver box. One switch has 2 options (left and right) to select wattage, and the other switch has 3 options for color temperatures (3500K, 4000K and 5000K), both can be adjusted to the desired combination.

1. Switches are located on the driver compartment. [See Figure 1]
2. Select a wattage and color temperature by sliding switch left or right respectively to the desired value. [See Figure 1]

Figure 1: Shows two slide switches on the driver compartment. One switch controls wattage with two positions (left/right). The other switch controls color temperature with three positions (3500K, 4000K, 5000K).

T-GRID / RECESSED MOUNTING

1. Use a screwdriver to lift and straighten the 4 hanging tabs. [See Figure 2]
2. Lay fixture into T-grid ceiling. [See Figure 2]
3. Use hanger wires to tie fixture hanging tabs off appropriately, in accordance with local building codes. (Hanger wires supplied by installer). [See Figure 3]
4. Then make all electrical connections to the fixture, in accordance with local electrical codes. [See Figure 4]

Figure 2: Illustrates using a screwdriver to lift and straighten the four hanging tabs on the fixture. It also shows the fixture being placed into a T-grid ceiling.

Figure 3: Shows how to use hanger wires to secure the fixture's hanging tabs to the ceiling structure, emphasizing compliance with local building codes. A safety cable is also depicted.

Figure 4: A general wiring diagram showing connections for Black (Line), White (Neutral), and Ground Wire to the fixture, connecting to a TO SOURCE (120-277V) power supply.

SUSPENDED MOUNTING (V-Hooks and Chain Sold Separately)

1. Secure ceiling plates into the ceiling by using expansion anchors and self-tapping screws. [See Figure 5]
2. Use a screwdriver to lift and straighten the hanging tabs. [See Figure 6]
3. Install V-hooks and chain. [See Figure 7]
4. Secure chain to the ceiling plates with a carabiner. [See Figure 8]
5. Then make all electrical connections to the fixture. [See Figure 9]

Figure 5: Depicts securing ceiling plates to the ceiling using expansion anchors and self-tapping screws.

Figure 6: Shows using a screwdriver to lift and straighten the hanging tabs on the fixture.

Figure 7: Illustrates installing V-hooks and chain for suspended mounting.

Figure 8: Shows securing the chain to the ceiling plates with a carabiner.

Figure 9: A general wiring diagram showing connections for Black (Line), White (Neutral), and Ground Wire to the fixture, connecting to a TO SOURCE (120-277V) power supply.

Specifications subject to change without notice. Photos and line drawings may not be to scale and are for general reference only.