Sunco Lighting 2x4 LED Ceiling Panel with Selectable CCT

Introduction

Prior to installation, remove the existing light fixture (if any) from the ceiling.

Required Tools: Drill, Ladder, Hammer, Pliers, Tape Measure, Pencil, Philips Screwdriver.

Easy Installation: Recessed Installation

1. Turn off the switch and circuit breaker before installing this LED light fixture.

   [Power OFF] ?

2. Turn the Ceiling Panel face down on a flat surface. Unscrew the two driver covers and set aside the screws.

3. Pop out two knockouts (choice of five).

4. Connect conduit to each knockout. Pass wires through.

5. Connect the supply wires to the Ceiling Panel wires with included wire nuts:

   • Black wire (live) to Black wire
   • White wire (neutral) to White wire
   • Green wire (ground) to Green wire

6. Optional for using a dimmer (not included): Connect the DIM+ (purple wire) and DIM- (pink wire) wiring of your Ceiling Panel to your dimmer with included wire nuts.

7. Replace driver covers. Tighten the screws.

8. Before proceeding: On the back of the panel, slide the CCT Selection Switch to choose from three color temperatures: 4000K, 5000K, or 6000K. The light will use the selected CCT setting when switched on.

9. Locate the four protective brackets on the back of the panel. Bend them up 90 degrees.

10. Twist the panel 90 degrees so the hook faces the outside edge of the Ceiling Panel.

11. Install the Ceiling Panel in the ceiling, using the protective brackets.

12. Turn on the circuit breaker and test the light.

    [Power ON] ✅

Wiring Diagram Description

The wiring diagram illustrates connections for:

• L (black wire)
• N (white wire)
• Ground wire (green)
• DIM- (pink wire)
• DIM+ (purple wire)

To make the light panel dimmable, connect a compatible dimmer (not included) to the dimming signal wires of the luminaire. Suitable for Constant Current Reduction Dimming 0-10V.

Easy Installation: Suspension Installation

Note: 2-piece suspension kits are required (not included).

1. Turn off the switch and circuit breaker before installing this LED light fixture.

   [Power OFF] ?

2. Turn the Ceiling Panel face down on a flat surface. Unscrew the two driver covers and set aside the screws.

3. Pop out two knockouts (choice of five).

4. Connect conduit to each knockout. Pass wires through.

5. Connect the supply wires to the Ceiling Panel wires with included wire nuts:

   • Black wire (live) to Black wire
   • White wire (neutral) to White wire
   • Green wire (ground) to Green wire

6. Optional for using a dimmer (not included): Connect the DIM+ (purple wire) and DIM- (pink wire) wiring of your Ceiling Panel to your dimmer with included wire nuts.

7. Replace driver covers. Tighten the screws.

8. Before proceeding: On the back of the panel, slide the CCT Selection Switch to choose from three color temperatures: 4000K, 5000K, or 6000K. The light will use the selected CCT setting when switched on.

9. Drill two holes in the ceiling. Place the anchors into the holes. Insert the wire rope and screw. Refer to the suspension kit's installation manual for complete details.

   [Suspension Kit components: Anchors, Wire rope, Screw]

10. Adjust the support rope/wire so the Ceiling Panel hangs horizontally. Suspension kit is not included.

11. Install the Ceiling Panel in the ceiling, using the protective brackets.

12. Turn on the circuit breaker and test the light.

    [Power ON] ✅

Specifications

To make the light panel dimmable, connect a compatible dimmer (not included) to the dimming signal wires of the luminaire. Suitable for Constant Current Reduction Dimming 0-10V.

Warning

To reduce the risk of fire, electric shock, or serious injury:

• Installation should be performed by a professional, qualified electrician familiar with the construction and operation of this product and the hazards involved.
• Abide by related regional and local laws or regulations.
• Proper grounding is required to ensure safety.
• Not suitable for a wet environment.
• LED must be installed in an appropriate environment to work. Harsh environments may damage the light or shorten its lifespan.
• Check for damage during shipping prior to installation. If the product is damaged, do not use it.
• Turn off the switch and circuit breaker before installing this LED light fixture. Recommended: Use an appropriate meter to accurately verify no voltage on the lines. After verifying there is no voltage, disconnect wires and remove existing light fixture from the ceiling (if any).
• After verifying no voltage, disconnect wires and remove existing light fixture from the ceiling (if any).
• To ensure efficient light, regularly clean the light panel. Do not clean with harsh solvents; use a dry cloth.
• Use safety precautions. Safety eyeglasses and gloves are recommended.