Fiilex Q5 COLOR User Guide
Safety Instructions
- DO NOT look into the light source. Be cautious of the high-intensity beam.
- DO NOT disassemble Q5 Color. This will void the warranty.
- DO NOT install Q5 Color in damp or wet locations.
- DO NOT obstruct the fixture's air vents.
- Use safety cable (not included) when rigging Q5 Color overhead.
- Only use Fiilex approved power supply and accessories. Failure to do so may damage the fixture.
- Shields, lenses or ultraviolet screens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired, for example by cracks or deep scratches.
- The lamp shall be changed if it has become damaged or thermally deformed.
- The luminaire is intended for professional use only.
Parts Diagram
The Fiilex Q5 COLOR features a comprehensive design with accessible controls and connection points. The diagram displays the fixture from multiple angles, highlighting key components.
- Vent Holes: Openings for airflow and cooling.
- Water Repellent Fabric: Material designed to protect internal components from moisture.
- Power Supply Unit (PSU): The component that supplies power to the fixture.
- Latch: Mechanism for securing or releasing parts of the fixture.
- Fresnel Lens: Optical element that shapes and directs light.
- Fresnel Lens Holder: Component that secures the Fresnel lens.
- Dual Locking V-Mount: A mounting system for attaching accessories or stands, offering dual locking for stability.
- Handles: Ergonomic grips for carrying or positioning the fixture.
- Beam Adjustment Knob: A control to modify the beam spread or focus.
- Tilt Lock Lever: A lever used to secure the fixture's tilt angle.
- Yoke (1/4"-20 UNC Screw Hole): The yoke assembly that allows for tilting and mounting, featuring a standard 1/4"-20 UNC threaded hole for accessories.
- Baby/Junior Pin Receiver: A standard mounting point for light stands and grip equipment.
- Mount Tightening Knob: A knob used to secure the fixture to its mount or stand.
- OLED Display: A screen showing operational status, settings, and information.
- Yoke Bolt: A bolt that secures the yoke, often allowing for adjustment.
- Intensity Control Knob: A knob used to adjust the light output level.
- CCT/HUE Knob: A control for adjusting the Color Correlated Temperature (CCT) or Hue.
- GN/SAT Knob: A control for adjusting Green/Magenta balance (GN) and Saturation (SAT).
- USB Type-A Port (5V/1A Power): A port for power output, typically for accessories.
- Navigation Pad: A directional control input for navigating menus and settings.
- ON/OFF Switch: A physical switch to turn the fixture on or off.
- USB Type-C Port (For updating firmware): A port used for firmware updates.
- DMX Output (XLR-Female 5-pin): A connector for sending DMX control signals to other devices.
- DC Input Port: The port for connecting the main power adapter.
- DMX Input (XLR-Male 5-pin): The primary port for receiving DMX control signals.
Fixture Operation
Mode Selection
To enter MODES, use the Navigation Pad [▶️]. Navigate through the available modes and select the desired one.
Fixture Control
1 Manual / Local Control:
Use the Intensity Control Knob [knob] and/or the Navigation Pad [▶️] to control parameters. For CCT modes and HSI modes, use either the CCT/HUE Knob [knob] and GN/SAT Knob [knob] or the Navigation Pad [▶️].
2 DMX / RDM:
The display shows DMX connection status: NO DMX or DMX OK.
Settings
Use the Navigation Pad [▶️] to enter and edit SETTINGS. Navigate to the right to access additional settings.
Fan Speed Options
| Option | Description |
|---|---|
| Off | The fan is completely off. (Operation time is limited.) |
| Variable | The fan speed varies based on light intensity. |
| Silent | The fan operates at reduced speed. |
| Full Speed | The fan operates at full speed. |
Dimming Options
| Option | Description |
|---|---|
| Sharp | Best for flash and strobe effects. |
| Smooth | Best for gradual fades. |
Info
View current fixture firmware versions and fixture temperature.
