HOTO Lithium Glue Gun - User Manual
Read this manual carefully before use, and retain it for future reference. Thanks for using HOTO Lithium Glue Gun.
01 Overview
The HOTO Lithium Glue Gun is designed for efficient and convenient use in crafting and home repairs. It is compatible with 7mm diameter glue sticks.
Key Components:
- 1. Glue gun cover
- 2. Glue gun muzzle
- 3. Indicator light
- 4. Power Switch
- 5. Glue Inlet
- 6. Trigger
- 7. Type-C Charging Port
02 Instructions
This product is applicable to hot glue sticks in 7mm diameter and can glue materials such as plastic, wood, paper products, textile, ceramic, glass, leather, crystal items, shells, and more.
Turn the product on/off
- To turn on: Press and hold the on/off button for 2 seconds.
- To turn off: Press and hold the on/off button for 2 seconds.
- The product will shut down automatically after 180 seconds of inactivity.
Instructions for Use
- When the product is turned on, insert a glue stick.
- When the indicator light is solid white (approx. 30 seconds), preheating is complete.
- Pull the trigger to eject glue.
- Apply glue to the items to be adhered, press them together, and wait for the glue to set.
Charge the battery
- The product is equipped with a USB charging cable and a Type-C charging port.
- Please charge the product to full if it is not used for a long time.
Indicator Status
| Light Status | Product Status |
|---|---|
| Blinking white | Heating Status |
| Solid white | Heating Done |
| Blinking red | Low Battery Notification |
| Slowly blinking red | Charging |
| Solid red light will go out after two minutes | Fully charged |
Warm Notice
- Remove the glue gun cover before use.
- Please do not touch the glue gun muzzle with hands when working.
- Melted glue is very high in temperature; please do not touch it with hands directly.
03 Troubleshooting
Precautions
- The product is not fully charged when leaving the factory; please charge before first use.
- The product cannot work while charging.
- On the first use, press the trigger a few times to push the glue stick into the holder for heating and gluing.
- When operation is done, if there is a remaining glue stick, do not pull it out with force to avoid damaging the product.
- After a long period of inactivity, if the indicator does not show correctly while charging, charge for 20 minutes and then check again.
- Please keep the product upright when not in use.
- The product only works with 7mm glue sticks.
Daily Care & Maintenance
- Do not expose the product to high temperatures for a long time. If it will not be used for a long period, store it in an environment with ambient temperature and moisture, and charge the battery every half year.
- Please keep the product surface clean and clean it with a wet soft cloth. Do not clean it with corrosive solutions.
Troubleshooting Table
| Fault | Cause | Solution |
|---|---|---|
| Product not work | Not power on | Turn on the switch |
| Turn off automatically | Turn on the switch | |
| No lithium battery power | Charge the battery | |
| No glue goes out | Run out of glue sticks | Add glue stick |
| Can't insert the glue stick | Size of glue sticks not matched | Replace glue stick |
04 Specifications
- Model: QWRJQ001
- Rated Voltage: 4V===
- Preheating Time: approx.30s
- Glue Stick Diameter: 7mm
- Item Dimensions: 135×127×35mm
- Glue Stick Length: 125mm
- Lithium-ion Battery: 2000mAh
- Charging parameters: 5V=1A
- Charging Time: 120-180min
- Net Weight: approx.200g
Manufactured by: Shanghai HOTO Technology Co., Ltd.
Address: Building 45, No.50 Moganshan Road, Putuo District, Shanghai
