M-Elec MR Slim Batten
Product Overview and Installation Guide
Product Information
M-Elec's updated slim batten features a snap-on diffuser for faster and more flexible installation. It includes upgraded larger terminal blocks for convenience, with rear entry and additional internal space simplifying cable routing. An external CCT switch allows users to select the desired lighting color temperature without opening the fitting. Available in 60cm and 120cm sizes to suit most applications, it comes standard with M-Elec's 5-year warranty.
Technical Information
| Feature | ML-MRSLB-60-M (60cm) | ML-MRSLB-120-M (120cm) |
|---|---|---|
| Total Power | 20W* | 40W* |
| MAX Lumen Output | WW: 1700lm NW: 1900lm W: 1800lm |
WW: 3400lm NW: 3800lm W: 3600lm |
| Colour Temp | WW 3000K, NW 4000K, W 6000K (Selectable via external switch) | |
| IP Rating | IP20 | |
| Efficacy | 90lm/w | |
| CRI | 80 | |
| Beam Angle | 120° | |
| Temp Range | 20° to 40°C | |
| Dimmable | No | |
| Power Supply | Integrated driver | |
| Average Life | 36000hrs** | |
| Operating current at 240V | 0.083A | 0.166A |
| Power Factor | 0.9 | |
| Connection | PA12 terminal block | |
| Construction | Aluminium base + PMMA diffuser | |
| Dimensions | 600 x 83.5 x 36.5mm | 1200 x 83.5 x 36.5mm |
| Weight | 0.4kg | 0.78kg |
| Warranty | 5 years | |
*Total power consumed including driver
**Average life is calculated on expected average lifespan
Dimensions Diagram Description:
- 60cm model: Length 600mm, Mounting hole spacing 475mm, Width 83.5mm, Height 83.5mm.
- 120cm model: Length 1200mm, Mounting hole spacing 1075mm, Width 83.5mm, Height 83.5mm.
For up-to-date specifications, visit: www.melec.com.au
Installation Guide
- Turn power off before commencing installation.
- Remove the diffuser by un-screwing the end cap (without CCT switch) and pulling the diffuser up.
- Place the base against the wall or ceiling and use suitable fixings for your type of installation.
- Wire the fitting according to the terminal markings.
Wiring Diagram Description: Shows connections for Live (L), Neutral (N), and Earth (E) to the terminal block. - Reinstall the diffuser and the end cap.
- Select the desired color output (3000K Warm White, 4000K Neutral White, 6000K White) on the end cap containing the CCT switch.
- Test according to all applicable standards and requirements.
Important Notes
MUST BE INSTALLED BY A LICENSED ELECTRICIAN
- Read instructions carefully before attempting to install the fitting. Retain this guide for future reference.
- Disconnect power before installing or servicing.
- This fitting is for outdoor use and should not be used in areas with limited ventilation or high ambient temperatures.
- Do not extend low voltage cables from the output of the power supply.
- All components must not be mechanically stressed.
- Be careful not to damage or destroy conductive paths on the circuit board.
- Follow all relevant electrical and safety standards (including AS3000).
- Correct electrical polarity must be observed, as the wrong polarity may destroy the product and is not covered under warranty.
- Damage by corrosion will not be honoured as a material defect claim. It is the user's responsibility to provide suitable protection against corrosive agents such as moisture, condensation, and other harmful elements.
Warranty Information
M-Elec offers a 5-year product warranty.
Additionally, M-World members may be eligible for a FREE 3-year ONSITE WARRANTY, which includes parts and labour, in conjunction with your standard product warranty.
For further information about warranties, please visit: melec.com.au/legal/warranties
M-Elec – Illuminated by design
M-Elec – Illuminated by design
