TECH EU-R-8b Plus Room Regulator

Warranty Card

Manufacturer: TECH STEROWNIKI II Sp. z o.o.

Warranty Period: 24 months from the date of sale.

Coverage: Free repair for defects caused by the manufacturer's fault. Device must be delivered to the manufacturer.

Governing Law: Act on specific terms and conditions of consumer sale and amendments of the Civil Code (Journal of Laws of 5 September 2002).

Important Caution: The temperature sensor must not be immersed in any liquid (e.g., oil) as this can damage the controller and void the warranty. Acceptable relative humidity is 5–85% RH without condensation.

User Restriction: The device is not intended for use by children.

Exclusions: Warranty does not cover settings/regulation parameters, normal wear parts (e.g., fuses), improper operation, user fault, mechanical damage, fire, flood, atmospheric discharges, overvoltage, short-circuit, unauthorized service, wilful repairs, modifications, or construction changes. Removing protective seals voids the warranty.

Service Calls: Costs of unjustified service calls are borne by the buyer. An unjustified call is defined as one for damages not resulting from the Guarantor's fault, or if the device defect is due to client fault, not covered by warranty, or external factors.

Claim Procedure: User must deliver the device at their own cost and risk, along with a correctly filled warranty card (including sale date, seller's signature, defect description) and proof of sale (receipt, VAT invoice). The warranty card is the sole basis for free repair. Complaint repair time is 14 days.

Lost Warranty Card: Manufacturer does not issue duplicates.

Safety Information

Before first use, read these regulations carefully. Non-compliance may lead to personal injury or controller damage. Store the manual safely for future reference. Ensure all users are familiar with the operation and security functions. If the device is sold or moved, ensure the manual accompanies it.

The manufacturer is not responsible for injuries or damage resulting from negligence. Users must take necessary safety measures.

Warnings:

• The regulator is not intended for use by children. [Warning]
• Any use other than specified by the manufacturer is forbidden. [Warning]
• The device should be installed by a qualified person. [Warning]

Environmental Commitment: TECH is committed to environmental protection. The crossed-out bin symbol [Recycling Symbol] on the product indicates it should not be disposed of with household waste. Users must transfer used equipment to a collection point for recycling of electric and electronic components.

Technical Data

EU Declaration of Conformity

TECH STEROWNIKI II Sp. z o.o., headquartered in Wieprz, Biała Droga 31, 34-122 Wieprz, declares that the room regulator EU-R-8b Plus is compliant with:

• Directive 2014/53/EU on radio equipment.
• Directive 2009/125/EC on ecodesign requirements for energy-related products.
• Regulation by the MINISTRY OF ENTREPRENEURSHIP AND TECHNOLOGY of 24 June 2019 concerning the restriction of hazardous substances in electrical and electronic equipment (implementing Directive (EU) 2017/2102).

Compliance assessment used harmonized standards, including:

• PN-EN IEC 60730-2-9 :2019-06 (Safety of use)
• PN-EN 62479:2011 (Safety of use)
• ETSI EN 301 489-1 V2.2.3 (Electromagnetic compatibility)
• ETSI EN 301 489-3 V2.1.1 (Electromagnetic compatibility)
• ETSI EN 300 220-2 V3.2.1 (Effective and coherent use of radio spectrum)
• ETSI EN 300 220-1 V3.1.1 (Effective and coherent use of radio spectrum)
• EN IEC 63000:2018 (RoHS)

Date of declaration: Wieprz, 19.10.2021

Product Description

The EU-R-8b Plus room regulator is designed to work with TECH external controllers and should be installed in heating zones. It transmits current room temperature and humidity readings to the external controller, which then manages thermostatic valves to maintain the desired temperature.

The screen displays the current temperature. The middle button [Button ●] allows switching between temperature and humidity display, and also confirms settings. The regulator enables permanent or temporary changes to the pre-set zone temperature.

Controller Equipment:

• Built-in temperature sensor
• Air humidity sensor
• Wall-mountable casing

How to Use the Regulator

The regulator features a display and three buttons:

• 1. Display: Shows current zone temperature.
• 2. Button [Button <]: Decreases value or navigates previous menu item.
• 3. Button [Button ●]: Changes displayed parameter (temperature/humidity), confirms settings, or enters the menu (hold).
• 4. Button [Button >]: Increases value or navigates next menu item.

To replace batteries or connect a floor sensor, remove the back cover.

Low Battery Indicator

When the regulator's battery is low, the screen will display "Lo" [Low Battery Indicator]. Replace batteries with 2xAAA 1.5V for proper operation.

How to Register a Room Regulator in a Given Zone

Each room regulator must be registered to a zone via the external controller menu (Zone / Registration / Sensor). After selecting the registration icon, press the button on the back of the room regulator.

Successful registration is confirmed on the external controller and the regulator displays "Scs". An "Err" message indicates a registration error.

Important Notes:

• Buttons must be unlocked for registration.
• Only one room regulator can be assigned per zone.
• A regulator can function as a floor sensor; press the communication button twice to register it as such.
• Hold the registration button to view the current software version.
• If "Una" appears despite correct registration, wait approximately 4 minutes or force communication by holding the registration button for 2 seconds until the program version is displayed.

Registration Rules:

• Once registered, a sensor cannot be unregistered but can be disabled in the external controller's zone submenu (select OFF).
• Assigning a new sensor to a zone with an existing sensor unregisters the first sensor.
• Assigning a sensor already registered to another zone unregisters it from the first zone and registers it in the new one.

Individual pre-set temperature values and weekly schedules can be set for each registered regulator via the external controller menu or www.emodul.eu. Pre-set temperatures can also be adjusted directly on the regulator using the [Button <] and [Button >] buttons.

How to Change the Pre-set Temperature

Adjust the pre-set zone temperature directly on the EU-R-8b Plus regulator using the [Button <] and [Button >] buttons. The current zone temperature is displayed during inactivity. Use the buttons to change the set value.

Setting Options:

• Permanently: Hold [Button >] until "Con" is displayed. The pre-set temperature will remain indefinitely. Confirm by pressing [Button ●].
• For a Specific Number of Hours: Press [Button <] or [Button >] until the desired number of hours (e.g., 01h) is displayed. The pre-set temperature will apply for that duration, after which the weekly schedule resumes. Confirm by pressing [Button ●].
• Apply Weekly Schedule: Press [Button <] until "OFF" is displayed. The pre-set temperature will revert to the weekly schedule settings. Confirm by pressing [Button ●].

Description of Menu Functions

Hold the middle button [Button ●] to enter the menu. Use [Button <] and [Button >] to navigate options.

1. HEA/COO: Selects heating (HEA) or cooling (COO) mode*. Requires a master zone controller with heating/cooling function and appropriate software.
2. BAT: Displays battery status in percentage (%).
3. CAL: Displays sensor calibration status.
4. LOC: Enables automatic button lock. Select "yes" or "no" to enable/disable. To unlock, hold [Button <] and [Button >] simultaneously.
5. DEF: Restores factory settings. Select "yes" or "no" to confirm.
6. RET: Exits the menu.

*Functionality requires a master zone controller with heating/cooling capability and compatible software.