Hozelock AquaPod 10 Automatic Watering System

Product Overview

The Hozelock AquaPod 10 (Model 2822) is an innovative automatic watering system designed to efficiently irrigate up to 5 planted containers. This system ensures your plants receive the right amount of water, promoting healthy growth while conserving water. It is ideal for patios, balconies, and small gardens.

Components

Required Components:

• Hozelock AquaPod 10 unit
• Water source (tap)
• Scissors or hose cutter
• Screwdriver (for optional wall mounting)
• Drill (for optional wall mounting)
• Wall plugs and screws (for optional wall mounting)

Optional Components:

• Hozelock AquaPod Plus Pod (Model 2824) for expanding the system
• Hozelock Plus Kit (Model 2825) for hanging baskets
• Hozelock AC1+ Water Timer (Model 2700) for automated watering schedules
• Hozelock Water Store Gels for water conservation
• Hozelock Water Butt Pump for using stored water

Included Parts:

• A - 2175 x1: Tap connector with 1/2" BSP and 3/4" BSP adapters.
• B - 93838-000 x1: Hose connector.
• C - 2772 x2: 10m of 4mm micro hose.
• D - 2824 x2: AquaPod Plus Pods.

Installation Guidelines

The AquaPod 10 is designed to water groups of up to 5 planted containers. The hose connecting the AquaPod to the tap should not exceed 10m. One or more drippers can be placed in each container.

AquaPods can be interconnected up to the 3rd generation. Additional AquaPods (2824) or hanging basket kits (2825) can be purchased separately, allowing up to seven additional kits to be combined with this system.

For maximum flexibility, up to 50m of 1/2" hose can be used between the tap and the hose connector (using 2 x 2166 and 1 x 2291 connectors, not supplied).

System Layout Example:

A central AquaPod 10 unit connects to a water source. From the AquaPod, micro hoses extend to individual plant pots. Additional AquaPods (2824) can be connected in series to extend the watering area. For larger areas, 10m micro hoses (2772) can be used to connect AquaPods or Plus Kits (2825) for hanging baskets.

Installation Steps

1. Connect to Tap: Attach the tap connector (A) to your outdoor tap. Ensure a secure connection.
2. Connect Hose: Push the 4mm micro hose (C) approximately 10mm into the fitting. If difficult, dip the hose end in warm water for 10 seconds and twist while pushing.
3. Position AquaPod: Lay the micro hose around your patio or garden area to position the AquaPod where needed. Trim any excess hose and store it for future use. Ensure the connection is not subjected to excessive force.
4. Prepare Drippers: Pull out the AquaPod hose to the required length and undo the dripper cap. Drippers can be closed if not needed.
5. Rewind Hoses: AquaPod hoses can be independently rewound by rotating the end cap opposite to the inlet hose.
6. Test System: Turn on the tap. Allow air to be expelled (may take a few minutes), then check for water emerging from the drippers.
7. Place Drippers: Insert the drippers into the plant pots. Ensure they are securely placed to direct water to the plant roots.

Optional Floor & Wall Mounting:

The AquaPod can be positioned temporarily on the floor or screwed permanently to a wall or floor. Use wall plugs and screws (not supplied) to attach the unit securely. The dripper hose can be extended up to 1m using remaining hose from component C.

Winter Storage

The AquaPod must be stored indoors when there is a risk of freezing temperatures. Before storing, rewind all hoses, drain the AquaPod unit completely, and store it in a frost-free environment to prevent damage.

Troubleshooting Guide