Product Overview
Before using this product, please read this user manual thoroughly and take good care of it.
Device Components:
- Wireless charging area for phone
- Clock display screen
- Brightness touch adjustment
- Phone charging indicator
- Watch charging indicator
- Earbuds charging case charging indicator
- Charging area for watch
- USB-C interface
- Wireless charging area for earbuds charging case
- Time setting "-" button
- Time setting "+" button
- Time setting button
Product Instructions
1. Before use, please unfold the wireless charging areas for the device's phone and watch. When unfolding or folding the device, do not forcefully rotate the wireless charging areas for the phone and watch to prevent damage to the device.
Visual Description: The device is shown in two states: folded and unfolded. In the unfolded state, the phone charging pad and watch charging stand are extended. The phone charging area is a flat pad, and the watch charging area is a small stand. The clock display is visible on the front. The device has a sleek, minimalist design with a USB-C port on the side.
2. Place your phone, watch, and earbuds charging case on the corresponding wireless charging area to charge.
Time Setting:
- Press the "Time Setting" button to select the 12/24 hour system.
- To set the hour: Press and hold the "Time Setting" button for 3 seconds to enter setting mode, then adjust the hour using the "+/-" button.
- To set the minutes: Press and hold the "Time Setting" button for 3 seconds, then briefly press the "Time Setting" button again to enter setting mode, and adjust the minutes using the "+/-" button.
Note: After setting, wait for 5 seconds to complete the setting.
Display Screen Adjustment:
Click the brightness touch adjustment icon to adjust the screen brightness. The screen brightness can be adjusted in four levels that cycle through sequentially.
| Level | Level 1 | Level 2 | Level 3 | Level 4 |
|---|---|---|---|---|
| Display brightness | Low | Medium | High | OFF |
Attention
- To maintain optimal performance and extend battery lifespan, recharge the clock every 15 days for at least 30 minutes.
- If the battery fully drains, the clock resets, requiring time reconfiguration. Additionally, promptly adjust for display variations caused by extreme temperatures.
- The clock features intelligent energy-saving, turning off the display after 10 minutes of being disconnected from power.
- To ensure that the charging station works properly, the phone case should not exceed 5 mm, the earbuds case should not exceed 4 mm, and the watch should be closely attached to the charging area.
- It may not be feasible to charge all three devices (the phone, the earbud charging case, and the watch) simultaneously if a charger higher than 18W power is not used.
- This product contains sensitive electronic components, including a battery, and can be damaged, impair functionality, or cause injury if dropped, burned, punctured, or crushed.
- Do not expose this product to high temperature or around heat generating devices such as heaters, microwave ovens, ovens, etc.
- Do not allow children or pets to swallow this product to avoid injury or other hazards.
- Radio waves generated by this product may interfere with pacemakers, defibrillators, or other medical devices. Maintain a safe distance of separation between medical devices and this product. Consult a physician and medical device manufacturer for information specific to medical devices. Stop using this product if interference is suspected.
- Please comply with local regulations for the disposal of this product and its accessories, and support recycling operations.
Indicator Light Guide
| Charging status | Plugged in | Standby | Charging | Fully charged | Abnormal objects detected |
|---|---|---|---|---|---|
| Indicator light | On for 3 Sec | OFF | Green light | Green light | Red light flashes |
Specification
- Input: 9V⌽2.22A
- Charging phone output: 10W (Max)
- Charging watch output: 2.5W (Max)
- Charging earbuds output: 3.5W (Max)
Warning
- Do not disassemble or change the internal structure of this product to avoid danger.
- Please use this product in the temperature range of 0°C - 40°C (32°F - 104°F). Do not use this product in high temperature and humid places to avoid equipment failure.
- Do not place metallic foreign objects in the wireless charging area.
- Do not throw this product into fire, otherwise it may cause the equipment to catch fire or explode.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Statement:
The equipment complies with IC Radiation exposure limit set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and the body.
IC Statement
This device complies with RSS-216 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.
RSS-Gen Issue 5 March 2019
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
