Assembly Instruction
Screw Accessories
| Part | Description | Quantity |
|---|---|---|
| S1 | M8*16 | x17 |
| S2 | M4*14 | x32 |
| S3 | x3 | |
| S4 | x4 | |
| S5 | x4 | |
| S6 | 3mm | x1 |
| S7 | 6mm | x1 |
| S8 | x4 |
Parts Accessories
| Part | Quantity |
|---|---|
| A | x2 |
| B | x1 |
| C | x1 |
| D | x1 |
| F | x1 |
| G | x1 |
| H | x1 |
| J | x1 |
| K | x1 |
| x2 |
Assembly Steps
Step 1
Attach the two frame pieces (A) to the base structure using screws S1 (x2).
Diagram shows two identical frame components (A) being secured to a larger base part.
Step 2
Connect the main desk frame components (B/C) using screws S1 (x2) and S7 (x1), along with parts D (x2) and J (x2).
Diagram illustrates the assembly of the central frame, showing parts B/C, D, and J being joined with screws S1 and S7.
Step 3
Attach the assembled frame (B/C) to the legs (A) using screws S1 (x9) and S7 (x1).
⚠️ Please make sure the table legs are vertical to the connecting rod. And then tighten all the screws.
Diagram shows the main frame being attached to the leg structures, with a close-up indicating the correct orientation and screw placement.
Step 4
Attach the desktop surface (F) to the assembled frame. Ensure the two boards are aligned and seamless, then tighten the screws (S2 x6, S3 x3).
Diagram shows the desktop board (F) being placed onto the frame and secured with screws. A note emphasizes alignment.
Step 5
Install the control box (K) and other components (H, S4 x4, S8 x4) to the underside of the desk.
Diagram illustrates the placement of the control box and associated wiring/components under the desktop.
Step 6
The assembly is now complete. The diagram shows the fully assembled standing desk.
Diagram shows the final assembled standing desk.
Instruction Manual
Control Panel Operation
Button Functions
- Up: [Up] button
- Down: [Down] button
- RESET: [RESET] button
- Stand: [Stand] button
- Sit: [Sit] button
Up and Down Button Operation
- When the [Up] button is pressed, the desktop runs up until reaching the highest height.
- When the [Down] button is pressed, the desktop runs down until it reaches the lowest height.
- When press the [Up] or [Down] button, the desktop runs automatically.
- When press the [Up] button for 3 seconds, release the button, the desktop automatically reaches the highest height. Press any button can stop halfway.
- When press the [Down] button for 3 seconds, release the button, the desktop automatically reaches the lowest height. Press any button can stop halfway.
Location Store/Memory Location Operation
- Storage of standing position: press and hold the [Stand] button for 5 seconds, and the standing position is saved.
- Storage of sitting position: press and hold the [Sit] button for 5 seconds, and the sitting position is saved.
- Stand memory position operation: press the [Stand] button, the desktop automatically runs to the height of the memory position, and press any button can stop halfway.
- Sitting memory position operation: press the [Sit] button, the desktop automatically runs to the height of the memory position, and press any button can stop halfway.
Reset Operation
Press and hold the [RESET] button for 5 seconds, then release the button to enter reset mode. The table will automatically run down to the lowest position for 5 seconds, and then the table will run up to a fixed position to stop.
Note: After the installation of the desk, please execute this reset process first.
Successful Installation Note
After the table is installed, please press the [RESET] key to start. During the reset process, the table will automatically run down to the lowest position for 5 seconds, and then the table will run up to a fixed position to stop. This indicates a successful installation.
Uses and Maintenance
Main Uses and Applications
Gaming, office, home.
Maintenance and Repair
When cleaning the table, use a soft towel dampened for scrubbing. Regularly maintain the operation of the lift; once you find that the parts are loose or other abnormal, you need to promptly repair or remove and replace them.
