Assembly Instruction
SCREW ACCESSORIES
S1: M8*16 (x16)
S2: M4*14 (x22)
S3: Small Plate (x3)
S4: Round Nut (x4)
S5: Clip (x4)
S6: Bracket (3mm) (x1)
S7: Bracket (6mm) (x1)
S8: Cable Tie (x4)
PARTS ACCESSORIES
A: Support Bar (x2)
B: Leg Frame (x1)
C: Leg Frame (x1)
D: Control Box Bracket (x2)
F: Desktop (x1)
H: Cable Management Tray (x1)
J: Motor Bracket (x2)
K: Motor Cable (x1)
Assembly Steps
Step 1
Attach Support Bars (A) to the Leg Frames (B and C) using Screws S1 (x4) and Bracket S7 (x1).
Visual Description: Two support bars are attached to the top of the leg frames, with one bracket connecting them.
Step 2
Assemble the leg frames (B/C x1) with the Motor Brackets (J x2) and Control Box Brackets (D x2). Use Screws S1 (x2) and Bracket S7 (x1). Attach the desktop support structure to the leg frames.
Visual Description: The leg frames are connected and the motor brackets and control box brackets are attached. The main frame is shown being attached to the leg assembly.
Step 3
Attach the assembled frame to the desktop (F). Secure the frame to the desktop using Screws S2 (x8) and S3 (x3). Ensure the two parts of the desktop are aligned and seamless before tightening.
Visual Description: The desk frame is positioned under the desktop, and screws are used to attach it. A warning symbol indicates the importance of proper alignment.
Step 4
Attach the Cable Management Tray (H) and Motor Brackets (J) to the underside of the desktop. Connect the Motor Cables (K) and secure them with Cable Ties (S8). Attach the Control Box to the bracket.
Visual Description: The cable tray and motor brackets are mounted. Cables are routed and secured with ties. The control box is mounted.
Step 5
Connect the cables from the motors to the control box. Ensure all connections are secure.
Visual Description: A diagram shows the motor cables connecting to the control box.
Step 6
Perform the reset operation. After the table is installed, press and hold the reset button (circular arrow/RESET) for 5 seconds to start the reset process. The table will move to its lowest position and then to a fixed position.
Visual Description: An illustration shows the control panel with buttons for up, down, reset, and memory presets. Instructions for the reset process are provided.
Control Panel Operation
Up and Down Button Operation
- Press the Up button (?) to raise the desktop to the highest height.
- Press the Down button (?) to lower the desktop to the lowest height.
- Pressing the Up or Down button will cause the desktop to move automatically.
- Pressing the Up or Down button and releasing it will cause the desktop to move automatically to the highest or lowest height respectively. Pressing any button can stop the movement halfway.
Location Store/Memory Location Operation
- Storage of standing position: Press and hold the Stand button (?) for 5 seconds to save the current height as the standing position.
- Storage of sitting position: Press and hold the Sit button (?) for 5 seconds to save the current height as the sitting position.
- Stand memory position operation: Press the Stand button (?) to automatically move the desktop to the saved standing height. Pressing any button can stop the movement halfway.
- Sitting memory position operation: Press the Sit button (?) to automatically move the desktop to the saved sitting height. Pressing any button can stop the movement halfway.
Reset Operation
- Press and hold the Reset button (? / RESET) for 5 seconds, then release the button to enter reset mode. The table will automatically run down to the lowest position for 5 seconds, and then the table will run up to a fixed position to stop.
- Important: After the initial installation of the desk, execute this reset process first.
General Information
Main uses and applications: Gaming, office, home.
Maintenance and Repair:
- When cleaning the table, use a soft towel dampened for scrubbing.
- Regularly maintain the operation of the lift. If you find that parts are loose or there are other abnormalities, promptly repair or remove and replace them.
Control Button Key
- Up button (?): Moves the desktop upwards.
- Down button (?): Moves the desktop downwards.
- RST: Reset button (? / RESET): Initiates the reset sequence.
- Stand button (?): Saves or recalls the standing height preset.
- Sit button (?): Saves or recalls the sitting height preset.
