Eufy Floodlight Cam E340 Quick Start Guide

Safety Instructions

General Safety:

• Check local laws for installation. If outside North America, installation and wiring must be done by a licensed electrician.
• This manual is for informational purposes only. Working with electricity can be dangerous; take proper safety precautions. Hire a licensed electrician if inexperienced.
• Disconnect power at the fuse or circuit breaker before installation.
• Do not install near flammable surfaces.
• Be cautious when working with electricity to avoid shock, injury, or death.
• Ensure the floodlight camera is properly grounded.
• The floodlight camera must be mounted on a wall and on a UL-listed junction box.

French Safety Instructions:

• Vérifiez les lois locales pour l'installation. Si vous êtes en dehors de l'Amérique du Nord, l'installation et le câblage doivent être effectués par un électricien agréé.
• Ce manuel est à titre informatif seulement. Travailler avec l'électricité peut être dangereux, il est donc important de prendre les précautions de sécurité appropriées. Engagez un électricien agréé si vous n'êtes pas à l'aise ou inexpérimenté avec les processus et les outils décrits.
• Déconnectez l'alimentation au fusible ou au disjoncteur avant l'installation.
• Ne pas installer le produit près de surfaces inflammables.
• Pour éviter le risque de choc, de blessure ou de décès, soyez toujours prudent lorsque vous travaillez avec l'électricité.
• Assurez-vous que la caméra de projecteur est correctement mise à la terre.
• La caméra de projecteur doit être montée sur un mur et sur une boîte de jonction homologuée UL.

What's in the Box

The following items are included:

• Floodlight Cam E340 (Model: T8425)
• USB Cable (For Quick Setup Only)
• Mounting Bracket (Pre-installed on Camera)
• Positioning Sticker
• Installation Hook
• Wall Screws (Bag A)
• Base Screws (Bag B)
• Bracket and Earth Screws (Bag C)
• Warning Sticker
• Quick Start Guide

What You Need (Not Provided):

• #2 or #1 Phillips Crosshead Screwdriver
• 5V/1A USB Power Adapter
• Ladder (If necessary)

At a Glance

The floodlight camera has the following components:

• ① Floodlight
• ② Speaker
• ③ Motion Sensor Component
• ④ System Indicator
• ⑤ Telephoto Camera
• ⑥ Wide Angle Camera
• ⑦ Infrared Component
• ⑧ Power Input (For Quick Setup)
• ⑨ SYNC Button
• ⑩ microSD Card Slot (Insert a microSD card* (not provided) to store recordings)
• ⑪ Mounting Bracket
• ⑫ Mounting Base

*Use at least a Class 10 microSD card with a maximum of 128 GB.

Setting Up the System

1. Download and install the Eufy Security app, then sign in or create an account.
2. Power on the floodlight camera using the USB-C charging cable and a power adapter (5V/1A, not provided). Note: The USB-powered connection is for initial setup inside your home. The floodlights will only activate in wired power mode.
3. Tap '+' in the app and follow the in-app instructions to add the camera.
4. Disconnect from the power adapter, then close the USB port cover. Important: Ensure the USB port cover is closed to prevent water entry.

Important Notes:

• To avoid scratching the camera, do not peel off the protective film until after installation.
• Make sure you can stream video from your floodlight camera BEFORE installation.

Preparing for Installation (Important)

Shut Power Off at the Breaker

Risk of Electrical Shock:

• Turn off the power at your circuit breaker or fuse box before proceeding. Consult a licensed electrician if needed.
• Switch the lights on/off to confirm power is off at the installation area.
• Verify the power supply is a 100~240 VAC 50/60 Hz source.
• Keep the breaker off during the entire installation process.

NOTE: Do not use a dimmer switch or timer with this product.

Installing Your Floodlight Camera

Separate the Mounting Bracket

Separate the mounting bracket from the camera and set it aside.

Select a Location

Mount the floodlight camera vertically on a wall or hang it from a ceiling. With the power off at the breaker, remove any existing floodlight if present.

Mounting Options:

• Wall Mounting
• Overhang Mounting

Recommended Height

Mount the camera 8 ft (2.44 m) above the ground for optimal motion detection range, up to 40 ft (12 m).

Install the Mounting Bracket

1. Run existing wires through the junction box hole.
2. Align the mounting bracket with the junction box screw holes. Remove foam from holes. Secure the bracket to the wall or ceiling using Bracket Screws (Bag C).

Connect Wires

Hang the camera on the bracket with the provided hook while connecting the wires.

Wire Connections:

• Connect the junction box's ground wire (bare copper/green/green & yellow), live wire (black), and neutral wire (white) to the floodlight camera's corresponding wires (green & yellow, black, white) using wire connectors. Secure with a screwdriver.
• If the existing ground wire is connected to the junction box, or if there is no ground wire, connect the floodlight camera's ground wire directly to the junction box or mounting plate.

Note: Never cross-connect wires. Ensure matching colors. Consult a licensed technician if you encounter issues.

Place the Camera on the Mounting Bracket

1. Remove the hook. Snap the mounting base onto the mounting bracket, align holes, and secure with 2 Base Screws (Bag B).
2. Remove the label and protective film from the floodlight. Clean the camera lens with a lens cleaning cloth.

Adjusting the Lighting Angle

Manually adjust the floodlight up/down or left/right for vertical or horizontal positioning.

Restoring Power

1. Switch on the main circuit breaker in the house.
2. Access features and settings in the Eufy Security app.

If the floodlight camera is not powered on, switch off the circuit breaker before checking the wiring. For troubleshooting, refer to the Help section in the Eufy Security app.

LED Light Guide

Safety Instructions (Continued)

• This equipment is not suitable for locations where children are likely to be present and is not intended for use by children.
• Do not use the product in any way not described herein to avoid personal injury or property damage.
• Users must comply with local laws and regulations, adhere to professional ethics, and pay attention to safety obligations. Use of Eufy products for illegal purposes is strictly prohibited. Eufy is not liable for any legal liability of violators.
• An appropriate disconnect device must be provided as part of the building installation.
• An all-pole mains switch compliant with Annex L must be incorporated into the building's electrical installation.
• The luminaire must be mounted on or over an outlet box and provided with supply conductors long enough to extend 150mm (6 in) into the outlet box.
• Caution, risk of electric shock.
• THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
• Use MIN 90°C SUPPLY CONDUCTORS.

Notice

NOTICE (United States of America)

FCC Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radio Frequency Exposure Statement: The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The minimum separation distance is 20cm.

Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.

Responsible Party:

• Company Name: POWER MOBILE LIFE, LLC
• Address: 10900 NE 8th St, Ste 501, Bellevue WA 98004
• Telephone: 1-800-988-7973

NOTICE (Canada)

IC Statement: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

IC RF Statement: When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matière d'exposition RF.

5150~5250 MHz can be used indoor only. 5150~5250 MHz peut être utilisé à l'intérieur uniquement.

NOTICE (Australia)

Do not use the Device in environments with excessively high or low temperatures, or expose it to strong sunshine or excessively wet conditions. The suitable temperature range for the device and accessories is -20°C to 40°C. A recommended temperature range for operation is 5°C to 25°C, with good ventilation.

This symbol indicates that the product must not be discarded as household waste. It should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling help protect natural resources, human health, and the environment. Contact your local municipality, disposal service, or retailer for more information.

Bluetooth® The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. Any use of these marks by Anker Innovations Limited is under license. Other trademarks and trade names are those of their respective owners.

NOTICE (Europe and United Kingdom)

CE Declaration of Conformity: Anker Innovations Limited declares that this device complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit: https://uk.eufylife.com/

UK Declaration of Conformity: Anker Innovations Limited declares that this device complies with the Radio Equipment Regulations 2017 (SI 2017/1206). The full UK declaration of conformity is available at: https://uk.eufylife.com/

RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of 20 cm from the device to the human body. To maintain compliance with RF exposure requirements, use products that maintain a 20cm distance between the device and the human body.

5150~5350 MHz can be used indoor only.

Customer Service

12-month limited warranty

Contact Information:

• (US): +1 (800) 988-7973
• (UK): +44 (0) 1604 936200
• (DE): +49 (0) 69 9579 7960
• (China): +86 400 0550 036
• (Japan): +81 03 4455 7823
• (AU): +61 3 8331 4800
• (Egypt): +20 8000000826
• (UAE): +971 8000320817
• (Kuwait): +965 22069086
• (Saudi Arabia): +966 8008500030

Email: support@eufylife.com

Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong.

Social Media:

• Facebook: @EufyOfficial
• Twitter: @EufyOfficial
• Instagram: @EufyOfficial