HAMMARÖN Pergola

General Information

As floor materials vary, screws for fixing the pergola to the floor are not included. For recommendations on suitable screw systems, contact your local specialised retailer.

Assembly typically requires two people and may require the use of a ladder for higher steps.

Parts List

Assembly Steps

Step 1: Prepare Upright Poles

Attach base plates (10106761) to the bottom of four upright poles. Use two screws (10110523) and the Allen key (130445) for each base plate. Ensure the base plate is oriented correctly.

Diagram shows hands attaching a base plate to the bottom of an upright pole, with screws and Allen key.

Step 2: Assemble Horizontal Beams (Part 1)

Connect connector plates (10106760) to the ends of four long horizontal beams. Use two screws (10101723) per plate. Ensure correct orientation, avoiding the incorrect configuration shown (❌).

Diagram shows connecting a connector plate to a horizontal beam with screws, and an example of incorrect assembly.

Step 3: Assemble Main Frame (Part 1)

Begin assembling the main frame by connecting the upright poles to the horizontal beams. The diagram shows connecting the top horizontal beams to the uprights. Pay attention to the correct orientation, as an incorrect assembly is indicated (❌).

Diagram shows connecting horizontal beams to upright poles, with an example of incorrect assembly.

Step 4: Assemble Main Frame (Part 2)

Connect the horizontal beams to the upright poles. Use screws (10101723) and washers (10101727). Arrows indicate the direction of insertion.

Diagram shows inserting screws and washers to connect horizontal beams to upright poles.

Step 5: Assemble Main Frame (Part 3)

Attach the remaining horizontal beams to the upright poles. Use screws (10101723) and the Allen key (130445).

Diagram shows hands tightening screws with an Allen key to connect horizontal beams to upright poles.

Step 6: Assemble Horizontal Beams (Part 2)

Connect the shorter horizontal beams to the upright poles. Use screws (10101723) and washers (10101727). Arrows indicate insertion.

Diagram shows inserting screws and washers to connect shorter horizontal beams to upright poles.

Step 7: Assemble Main Frame (Part 4)

Connect the remaining horizontal beams to the upright poles. Use screws (10101723) and the Allen key (130445).

Diagram shows hands tightening screws with an Allen key to connect horizontal beams to upright poles.

Step 8: Assemble Roof Support Poles

Assemble the roof support poles by inserting the shorter poles into the longer poles. The diagram shows 4 connections being made.

Diagram shows inserting poles into each other to form longer roof support poles.

Step 9: Attach Rings to Roof Supports

Attach the rings (10106786) to the roof support poles. The diagram shows 4 rings being attached to one pole, with a hand indicating the action.

Diagram shows hands hooking rings onto a roof support pole.

Step 10: Assemble Side Frame Sections

Assemble the side frame sections. Connect the horizontal and vertical pieces using screws. The diagrams show hands guiding the parts and screws being inserted.

Diagrams show hands assembling side frame components with screws.

Step 11: Assemble Main Frame (Part 5)

Assemble the main frame structure by connecting the uprights and horizontal beams. Arrows indicate the direction of connection. Use screws (10101723) and washers (10101727).

Diagram shows connecting frame components with arrows indicating movement and screws being inserted.

Step 12: Assemble Roof Structure

Assemble the roof structure by connecting the roof support poles. Arrows indicate the folding and connecting motion.

Diagram shows the roof frame being unfolded and connected.

Step 13: Erect Main Frame

Erect the main frame structure. This step typically requires two people. Use a ladder for higher connections. The diagram shows connecting two pieces with a sliding motion.

Diagram shows two people on ladders erecting the pergola frame, with a close-up of two parts sliding together.

Step 14: Secure Roof Structure

Secure the roof structure to the main frame. Use 4x screws (10101723) with washers (10101727) for some connections, and 8x screws (10101723) with washers (10101727) for others. The Allen key (130445) is used for tightening.

Diagram shows securing the roof frame with screws and washers, using an Allen key. Close-ups show the screw and washer configuration.

Step 15: Attach Hook Brackets

Attach the hook brackets (10106787) to the frame using screws (10110523).

Diagram shows attaching hook brackets to the frame with screws.

Step 16: Assemble Curtain Support Poles

Assemble the curtain support poles by inserting the poles into each other until they click. The diagram shows 5 connections being made.

Diagram shows poles being inserted into each other, with the word "Click!" indicating connection.

Step 17: Attach Roof Fabric

Attach the roof fabric to the frame. The diagram shows one end being secured to a pole.

Diagram shows the roof fabric being attached to a support pole.

Step 18: Hang Side Curtains (Part 1)

Hang the side curtains using the rings. The diagram shows 4 rings being hooked onto the frame.

Diagram shows hands hooking rings onto the pergola frame to attach side curtains.

Step 19: Hang Side Curtains (Part 2)

Hang the remaining side curtains using the rings. The diagram shows 16 rings being hooked onto the frame.

Diagram shows hands hooking rings onto the pergola frame to attach side curtains.

Step 20: Secure Roof Fabric

Secure the roof fabric. The diagram shows a flap being tucked into a pocket.

Diagram shows a flap of the roof fabric being secured into a pocket.

Step 21: Attach Corner Supports

Attach the corner supports (10106761) to the base of the pergola legs. The diagram shows them being pressed down.

Diagram shows corner supports being pressed onto the base of the pergola legs.

Step 22: Secure Pergola to Ground

Secure the pergola to the ground for stability.

• For grass or soil: Insert ground stakes (10102303) into the base of the legs using a hammer. ⚠️ Use caution when hammering to avoid injury.
• For hard surfaces: Use appropriate screws (not included) to attach the base plates to the ground. The diagram shows screws being inserted into the base plates.

Diagrams show ground stakes being hammered into the ground and screws being used to attach to a hard surface.

Step 23: Final Curtain Attachment

Complete the attachment of the side curtains. The diagram shows a flap being secured.

Diagram shows a flap of the side curtain being secured.

Product Information

© Inter IKEA Systems B.V. 2023

Document Reference: AA-2392027-2