Dryer Safety
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
⚠️ This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:
❗ DANGER: You can be killed or seriously injured if you don't immediately follow instructions.
⚠️ WARNING: You can be killed or seriously injured if you don't follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
⚠️ WARNING - "Risk of Fire"
- Clothes dryer installation must be performed by a qualified installer.
- Install the clothes dryer according to the manufacturer's instructions and local codes.
- Do not install a clothes dryer with flexible plastic venting materials or flexible metal (foil type) duct. If flexible metal duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.
- To reduce the risk of severe injury or death, follow all installation instructions.
- Save these instructions.
IMPORTANT: When discarding or storing your old clothes dryer, remove the door.
Important Safety Instructions
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions, including the following:
- Read all instructions before using the dryer.
- Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.
- Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.
- Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near children.
- Before the dryer is removed from service or discarded, remove the door to the drying compartment.
- Do not reach into the dryer if the drum is moving.
- Do not install or store the dryer where it will be exposed to the weather.
- Do not tamper with controls.
- Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand and have the skills to carry out.
- Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.
- Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.
- Clean lint screen before or after each load.
- Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.
- The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel.
- See "Electrical Requirements" located in the installation instructions for grounding instructions.
SAVE THESE INSTRUCTIONS
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.
Operating Instructions
Control Panel and Features
1 START BUTTON: Press to start a cycle. Indicator light will glow to indicate the cycle has started.
2 TEMPERATURE BUTTON: The Temperature Control button lets you choose between a normal and low drying temperature.
- Normal: The Normal temperature setting is for sturdy fabrics, such as cotton, linen, and denim. If the Temperature Control button is not pressed in, the temperature setting is Normal.
- Low: The Low setting is for synthetics, such as cotton/polyester blend, rayon, acetate, washable silk, or nylon. If the Temperature Control button is pressed in, the temperature setting is Low.
NOTE: Always refer to the care label on the garment to determine whether it can be tumble dried.
3 POWER: Press to turn the dryer on and off. Press again to stop/cancel a cycle at any time.
4 CYCLE CONTROL KNOB: Use your dryer's Cycle Control knob to select available cycles on your dryer. Turn the knob to select a cycle for your laundry load. See “Cycle Guide" for detailed descriptions of cycles.
5 POWER INDICATOR: This light flashes when the power is on and glows when a cycle is running.
END OF CYCLE SIGNAL: The dryer sounds a signal to let you know when the cycle is complete. The signal is not adjustable and cannot be turned off. The signal is helpful when you are drying permanent press, synthetics, and other items that should be removed promptly at the end of the cycle.
Cycle Guide – Sensor Dry Cycles
Use Sensor Dry Cycles for better fabric care and energy savings.
When you are using the GentleBreeze™ Drying System with IntelliDry® Sensor, two metal strips located in the dryer determine the dryness of the load. When there is moisture left in the clothes, the dryer will continue to run. As clothes begin to dry, the amount of water left in the clothes decreases, and the timer advances through the remainder of the cycle. When the selected dryness level is reached, the dryer goes into a cool-down period.
Sensor dry cycles may be used for most loads. Sensor dry cycles give the best drying results in the shortest time. Drying time varies according to the type of fabric, size of the load, and dryness setting.
After drying a load, check the dryness:
- If the load is drier than you like, select a setting closer to Iron Dry the next time you dry a similar load.
- If a load is not as dry as you like, complete drying using a Timed cycle. Select a setting closer to Extra Dry the next time you dry a similar load.
| Items to dry: | Cycle: | Temperature Setting: |
|---|---|---|
| Cotton/Linen Heavy cottons and denims Cottons and linens | Extra Dry Normal | Normal Normal |
| Synthetics White and colorfast permanent press White and colorfast items that require ironing Polyester/acrylic blends, rayon, acetate Washable silk and nylon | Normal Iron Dry Damp Dry Damp Dry | Low Low Low Low |
Cycle Guide – Timed Dry Cycles
IMPORTANT: It is not recommended drying heavyweight items in Timed Dry cycle. Heavyweight items can be dried using automatic cycles.
Use this cycle to get up to 60 minutes of heated drying time or to complete drying if items are still damp after the automatic cycle. Timed Dry is useful for lightweight items, such as lingerie, blouses, and knits that require a short drying time.
| Items to dry: | Time (Minutes): | Temperature Setting: |
|---|---|---|
| White and colorfast permanent press | 40 | Low |
| White and colorfast items that require ironing | 40 | Low |
| Polyester/acrylic blends, rayon, acetate | 40 | Low |
| Washable silk and nylon | 40 | Low |
Using Your Dryer
⚠️ WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
1. Clean the lint screen
Clean the lint screen before each load. Pull the lint screen straight up. Open lint screen. Roll lint off the screen with your fingers. Do not rinse or wash screen to remove lint. Wet lint is hard to remove. Close lint screen. Push the lint screen firmly back into place.
For additional cleaning information, see "Dryer Care."
Diagram shows a hand pulling up a lint screen from the dryer door opening, then rolling lint off the screen.
2. Load the dryer
Open the door by pulling on the handle. Place laundry in the dryer. Add a static reducing sheet to wet load, if desired. Close the door.
IMPORTANT: Do not tightly pack the dryer. Items need to tumble freely. Tightly packing the load can lead to poor drying performance and may increase wrinkling and tangling.
Diagram shows the dryer door open, with laundry being placed inside.
3. Press POWER
Press the POWER button to turn on the dryer.
Diagram shows the POWER button on the control panel.
4. Press TEMPERATURE
Press the TEMPERATURE button to select the recommended temperature setting for the type of load being dried.
Diagram shows the TEMPERATURE button and the Normal/Low indicator lights on the control panel.
5. Select the desired cycle
Select the desired cycle for your load. See the "Cycle Guide" for more information about each cycle.
NOTE: Most loads may be dried using the Normal dryness level, which is shown in bold letters on the control panel. Normal is the energy preferred dryness level and will use the least energy.
Diagram shows the CYCLE CONTROL KNOB with various cycle selections like TIMED DRY, EXTRA DRY, AUTO DRY, NORMAL, IRON DRY, DAMP DRY.
6. Press START to begin cycle
Press and hold the START button to begin the cycle.
Diagram shows the START button on the control panel.
To stop your dryer at any time: Turn the Cycle Control knob to the STOP position, push the POWER button, or open the door.
To restart the dryer:
- Close the door.
- Select a new cycle and temperature (if desired).
- Press the START button.
To change the cycle or temperature after pressing START:
- Open the dryer door.
- Press the TEMPERATURE button to change the temperature (if desired).
- Turn the cycle knob to the new desired position.
- Press the START button.
Dryer Care
Cleaning the Dryer Location
Keep dryer area clear and free from items that would block the air flow for proper dryer operation. This includes clearing piles of laundry in front of the dryer.
⚠️ WARNING
Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from dryer.
Place dryer at least 18 inches (460 mm) above the floor for a garage installation.
Failure to do so can result in death, explosion, or fire.
Cleaning the Dryer Interior
To clean dryer drum:
- Use a mild hand dish detergent mixed at a low concentration with very warm water, and rub with a soft cloth.
- Rinse well with a wet sponge or towel.
3. Tumble a load of clean clothes or towels to dry drum OR Use a microfiber cloth and hot water in a spray bottle to clean the drum and a second microfiber towel to dry.
NOTE: Garments that contain unstable dyes, such as denim blue jeans or brightly colored cotton items, may discolor the rear of the dryer interior. These stains are not harmful to your dryer and will not stain future loads of clothes. Dry unstable dye items inside out to avoid transfer of dye.
Removing Accumulated Lint
From Inside the Dryer Cabinet: Lint should be removed every 2 years, or more often, depending on dryer usage. Cleaning should be done by a qualified appliance servicer or ventilation system cleaner.
From the Exhaust Vent: Lint should be removed every 2 years, or more often, depending on dryer usage.
Cleaning the Lint Screen
Every load cleaning: The lint screen is located in the door opening of the dryer. The control panel has an indicator light to remind you to clean the lint screen before each load. A screen blocked by lint can increase drying time.
To clean:
- Pull the lint screen straight up. Open lint screen. Roll lint off the screen with your fingers. Do not rinse or wash screen to remove lint. Wet lint is hard to remove.
2. Close lint screen. Push the lint screen firmly back into place.
IMPORTANT:
- Do not run the dryer with the lint screen loose, damaged, blocked, or missing. Doing so can cause overheating and damage to both the dryer and fabrics.
- If lint falls off the screen into the dryer during removal, check the exhaust hood and remove the lint. See "Venting Requirements.”
As needed cleaning: Laundry detergent and fabric softener residue can build up on the lint screen. This buildup can cause longer drying times for your clothes, or cause the dryer to stop before your load is completely dry. The screen is probably clogged if lint falls off while the screen is in the dryer.
Clean the lint screen with a nylon brush every 6 months, or more frequently, if it becomes clogged due to a residue buildup.
Cleaning the Lint Screen (cont.)
To wash:
- Roll lint off the screen with your fingers.
- Wet both sides of lint screen with hot water.
- Wet a nylon brush with hot water and liquid detergent. Scrub lint screen with the brush to remove residue buildup.
- Rinse screen with hot water.
- Thoroughly dry lint screen with a clean towel. Reinstall screen in dryer.
Diagram shows a lint screen being cleaned with a brush and water.
Vacation, Storage, and Moving Care
Install and store your dryer where it will not freeze. Because some water may stay in the hoses, freezing can damage your dryer. If storing or moving your dryer during freezing weather, winterize it.
Non-Use or Storage Care: Operate your dryer only when you are at home. If you will be on vacation or not using your dryer for an extended period of time, you should:
- Unplug dryer or disconnect power.
- Clean lint screen. See “Cleaning the Lint Screen.”
Moving Care: For power supply cord-connected dryers:
- Unplug the power supply cord.
- Make sure leveling legs are secure in dryer base.
- Use masking tape to secure dryer door.
⚠️ WARNING
Electrical Shock Hazard
Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.
For direct-wired dryers:
- Disconnect power.
- Disconnect wiring.
- Make sure leveling legs are secure in dryer base.
- Use tape to secure dryer door.
Reinstalling the Dryer: Follow the "Installation Instructions" to locate, level, and connect the dryer.
Installation Instructions
Installation Requirements
Tools and Parts
Gather the required tools and parts before starting installation.
Tools needed:
- Flat-blade screwdriver
- Wood block
- Wire stripper (direct wire installations)
- Tin snips (new vent installations)
- 1/4" (7 mm) nut driver (recommended)
- Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench
- Level
- Caulking gun and compound (for installing new exhaust vent)
- Torx T20® Security screwdriver
Diagrams show images of each tool listed.
Parts needed: (Not supplied with dryer)
- Vent clamps
- Vent elbows and ductwork
Additional parts may be required, depending on your installation. Check local codes. Check existing electrical supply and venting. Read "Electrical Requirements" and "Venting Requirements" before purchasing parts.
If using a power supply cord: Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain:
- A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft. (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.
- A UL listed strain relief.
Parts supplied: Parts package is located in dryer drum. Check that all parts are included.
NOTE: Do not use leveling legs supplied if installing with a pedestal or a stack kit.
Coupling
Options: (Not supplied with dryer)
Pedestal: You may order a pedestal separately for this dryer. This pedestal will add about 12" (305 mm) to the height of your unit for a total height of approximately 45" (1.14 m). To order, call the dealer from whom you purchased your dryer or refer to the "Assistance or Service" section of this manual. Ask for Model Number LAB0050PQ.
Stack kit: Are you planning to stack your washer and dryer? Your dryer is shipped with Stack Kit W10178021, which fits Whirlpool® washer models starting with WFC. If you have any other washer model, call the dealer from whom you purchased your dryer or refer to the "Assistance or Service" section of this manual.
Diagrams show images of a coupling, pedestal, and stack kit.
Location Requirements
Check code requirements. Some codes limit, or do not permit, installing dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.
⚠️ WARNING
Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from dryer.
Place dryer at least 18 inches (460 mm) above the floor for a garage installation.
Failure to do so can result in death, explosion, or fire.
You will need:
- A location allowing for proper exhaust installation. See "Venting Requirements."
- A separate 30 amp circuit.
- If using power supply cord, a grounded electrical outlet located within 2 ft. (610 mm) of either side of dryer. See "Electrical Requirements."
- Floor must support dryer weight of 200 lbs. (90.7 kg). Also consider weight of companion appliance.
- Level floor with maximum slope of 1" (25 mm) under entire dryer.
- For garage installation, place dryer at least 18" (460 mm) above floor. If using a pedestal, you will need 18" (460 mm) to bottom of dryer.
- The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.
IMPORTANT: Do not operate, install, or store dryer where it will be exposed to water, weather, or at temperatures below 45° F (7° C). Lower temperatures may cause dryer not to shut off at end of sensor cycles, resulting in longer drying times.
Installation Clearances
Space must be large enough to allow door to fully open.
Diagram shows front, side, and back views of the dryer with dimensions and required clearances for installation. Front view: 23 3/8" (594 mm) width, 33 1/4" (845 mm) height. Side view: 39" (991 mm) depth, 23 1/4" (603 mm) width. Back view: 31 1/4" (83 mm) height, 27" (686 mm) depth, 11 3/4" (299 mm) width at base, showing power supply cord/cable and vent connection. Note indicates minimum 3" (76 mm) clearance behind dryer for exhaust vent.
Installation Spacing
Recessed area or closet installation
- All dimensions show recommended and minimum spacing allowed.
- Additional spacing should be considered for ease of installation and servicing.
- Additional clearances might be required for wall, door, floor moldings, and dryer venting.
- Additional spacing should be considered on all sides of the dryer to reduce noise transfer.
- For closet installation with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.
- Companion appliance spacing should also be considered.
Diagram shows clearances for recessed or closet installation (dryer only): 18" min (457 mm) from wall to front, 3" (76 mm) side clearance, 1" (25 mm) front/back clearance from console/base, 48 in.² (310 cm²) top ventilation, 24 in.² (155 cm²) bottom ventilation.
Custom undercounter installation (dryer only):
Diagram shows dimensions for custom undercounter installation: 33 1/4" (845 mm) height, 23 3/8" (594 mm) width, 1" (25 mm) clearance on sides and front/back.
Recessed or closet installation - Stacked with stack kit:
Diagram shows clearances for stacked installation: 12" (305 mm) width, 66 1/4" (1683 mm) height, 3" (76 mm) side clearance, 1" (25 mm) front/back clearance, 48 in.² (310 cm²) top ventilation, 24 in.² (155 cm²) bottom ventilation.
Mobile home - Additional installation requirements:
This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile home construction and Safety, Title 24, HUD Part 280).
Mobile home installations require:
- Metal exhaust system hardware, available for purchase from your dealer.
- Special provisions must be made in mobile homes to introduce outside air into dryer. Openings (such as a nearby window) should be at least twice as large as dryer exhaust opening.
Electrical Requirements
It is your responsibility:
- To contact a qualified electrical installer.
- To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSI/NFPA 70 – latest edition and all local codes and ordinances.
The National Electrical Code requires a 4-wire power supply connection for homes built after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations.
A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269.
- To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz, AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. Connect to an individual branch circuit. Do not have a fuse in the neutral or grounding circuit.
- Do not use an extension cord.
- If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.
Electrical Connection
To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions in "Electric Installation."
- This dryer is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground conductor is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical supply connection, see "4-Wire Direct Wire Connection."
- A 4-wire power supply connection must be used when the appliance is installed in a location where grounding through the neutral conductor is prohibited. Grounding through the neutral is prohibited for (1) new branch-circuit installations after 1996, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductors.
If using a power supply cord:
Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain:
- A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft. (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.
- A UL listed strain relief.
If your outlet looks like this:
Diagram shows a 4-wire receptacle (NEMA Type 14-30R).
Then choose a 4-wire power supply cord with ring or spade terminals and UL listed strain relief. The 4-wire power supply cord, at least 4 ft. (1.22 m) long, must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground conductor) may be either green or bare. The neutral conductor must be identified by a white cover.
If your outlet looks like this:
Diagram shows a 3-wire receptacle (NEMA Type 10-30R).
Then choose a 3-wire power supply cord with ring or spade terminals and UL listed strain relief. The 3-wire power supply cord, at least 4 ft. (1.22 m) long, must have three 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 10-30R.
If connecting by direct wire:
Power supply cable must match power supply (4-wire or 3-wire) and be:
- Flexible armored cable or nonmetallic sheathed copper cable (with ground wire), covered with flexible metallic conduit. All current-carrying wires must be insulated.
- 10-gauge solid copper wire (do not use aluminum) at least 5 ft. (1.52 m) long.
Electric Installation
For power supply cord installations:
⚠️ WARNING
Fire Hazard
Use a new UL listed 30 amp power supply cord.
Use a UL listed strain relief.
Disconnect power before making electrical connections.
Connect neutral wire (white or center wire) to center terminal (silver).
Ground wire (green or bare wire) must be connected to green ground connector.
Connect remaining 2 supply wires to remaining 2 terminals (gold).
Securely tighten all electrical connections.
Failure to do so can result in death, fire, or electrical shock.
For direct wire installations:
⚠️ WARNING
Fire Hazard
Use 10 gauge copper wire.
Use a UL listed strain relief.
Disconnect power before making electrical connections.
Connect neutral wire (white or center wire) to center terminal (silver).
Ground wire (green or bare wire) must be connected to green ground connector.
Connect remaining 2 supply wires to remaining 2 terminals (gold).
Securely tighten all electrical connections.
Failure to do so can result in death, fire, or electrical shock.
Before you start: disconnect power.
1. Choose electrical connection type
Diagram shows icons for a 4-wire receptacle, a 3-wire receptacle, 4-wire direct connection, and 3-wire direct connection.
Power supply cord 4-wire receptacle (NEMA Type 14-30R). Go to "Power Supply Cord Connection."
Power supply cord 3-wire receptacle (NEMA Type 10-30R). Go to "Power Supply Cord Connection."
4-wire direct connection: Go to "Direct Wire Connection."
3-wire direct connection: Go to "Direct Wire Connection."
2. Remove terminal block cover
Diagram shows the back of the dryer with the terminal block cover being removed after a hold-down screw is taken out.
Remove hold-down screw and terminal block cover.
Power Supply Cord Connection
Power supply cord strain relief:
1. Attach power supply cord to strain relief
Diagram shows a close-up of the strain relief mechanism with labels A, B, C. A is the strain relief, B is the locking nut, C is the power supply cord.
Unscrew the strain relief (A) from the terminal block cover. Unscrew the strain relief nut (B) from the strain relief (A). Put the power supply cord (C) through the strain relief nut (B), then the strain relief (A). Be sure that the wire insulation on the power supply cord is inside the strain relief.
2. Replace strain relief
Diagram shows the strain relief being reattached to the terminal block cover with labels A, B, C, D. D is the power cord.
Replace strain relief (B) (with power cord [D] inserted) back into the terminal block cover (A). Connect locking nut to strain relief on inside of terminal block cover. Do not tighten strain relief nut (C).
If your outlet looks like this:
Diagram shows a 4-wire receptacle (NEMA Type 14-30R) and a 4-prong plug.
Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to "4-Wire Power Supply Cord Connection" on this page.
If your outlet looks like this:
Diagram shows a 3-wire receptacle (NEMA Type 10-30R) and a 3-prong plug.
Power supply cord 3-wire receptacle (NEMA Type 10-30R): Go to "3-Wire Power Supply Cord Connection" on page 15.
4-Wire Power Supply Cord Connection
IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections.
1. Remove neutral ground wire
Diagram shows the terminal block with labels A, B, F. F is the neutral ground wire being removed from screw A.
Remove the neutral ground wire (F) located inside the dryer cabinet, behind the external ground conductor screw (A).
2. Connect ground wire and neutral wire
Diagram shows the terminal block with labels A, B, D, E. Wire E (ground) is connected to screw A. Wire D (neutral) is connected to screw B.
Connect ground wire (E) (green or bare) of power supply cord to external ground conductor screw (A). Tighten screw. Connect neutral wire (D) (white or center wire) of power supply cord under center screw (B) of the terminal block.
3-Wire Power Supply Cord Connection
Use where local codes permit connecting cabinet-ground conductor to neutral wire.
Diagram shows a 3-wire receptacle (NEMA Type 10-30R), a 3-prong plug, spade terminals, and ring terminals.
1. Remove center screw
Diagram shows the terminal block with screw B being removed.
Remove center terminal block screw (B).
2. Connect neutral wire
Diagram shows the terminal block with labels B, D. Wire D (neutral) is connected to screw B.
Connect neutral wire (white or center) (D) of power supply cord under center terminal block screw (B). Tighten screw.
3. Connect remaining wires
Diagram shows the terminal block with wires connected to outer screws.
Connect remaining wires under outer terminal block screws. Tighten screws. Replace the terminal block cover on the back of dryer. Tighten strain relief nut. Now, go to "Venting Requirements."
Direct Wire Connection
If your wiring looks like this:
4-wire direct connection: Go to "4-Wire Direct Connection" on this page.
If your wiring looks like this:
Diagram shows a 3-wire direct connection cable.
3-wire direct connection: Go to "3-Wire Direct Connection" on page 17.
4-Wire Direct Wire Connection
IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit 3-wire connections.
1. Prepare your 4-wire cable for direct connection
Diagram shows a 4-wire cable with dimensions for stripping and shaping wire ends into hooks. Lengths: 5" (127 mm) outer covering, 1 1/2" (38 mm) cut from 3 wires, 1" (25 mm) strip insulation.
Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 5" (127 mm) of outer covering from end of cable, leaving bare ground wire at 5" (127 mm). Cut 1 1/2" (38 mm) from remaining 3 wires. Strip insulation back 1" (25 mm). Shape ends of wires into hooks.
2. Remove neutral ground wire
Diagram shows the terminal block with labels A, B, F. Wire F (neutral ground) is removed from screw A.
Remove the neutral ground wire (white) (F) located inside the dryer cabinet, behind the external ground conductor screw (A).
3. Connect power supply cable wire
Diagram shows the terminal block with labels A, B, D, E. Wire E (ground) is connected to screw A. Wire D (neutral) is connected to screw B.
Place hooked end of ground wire (E) (green or bare) of power supply cord under external ground conductor screw (A). Squeeze hooked end together and tighten screw. Connect hooked end of neutral wire (D) (white or center wire) of power supply cord under center screw (B) of the terminal block. Squeeze hooked end together and tighten screw.
4. Connect remaining wires
Diagram shows the terminal block with remaining wires connected to outer screws.
Place hooked ends of remaining direct wire cable wires under outer terminal block screws (hooks facing right). Squeeze hooked ends together and tighten screws. Replace the terminal block cover on the back of the dryer. Tighten strain relief nut. Now, go to "Venting Requirements."
3-Wire Direct Wire Connection
Use where local codes permit connecting cabinet-ground conductor to neutral wire.
1. Prepare your 3-wire cable for direct connection
Diagram shows a 3-wire cable with dimensions for stripping and shaping wire ends into hooks. Lengths: 3 1/2" (89 mm) outer covering, 1" (25 mm) strip insulation.
Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 3 1/2" (89 mm) of outer covering from end of cable. Strip insulation back 1" (25 mm). If using 3-wire cable with ground wire, cut bare wire even with outer covering. Shape wire ends into hooks.
2. Remove center screw
Diagram shows the terminal block with screw B being removed.
Remove center terminal block screw (B).
3. Connect neutral wire
Diagram shows the terminal block with labels B, D. Wire D (neutral) is connected to screw B.
Place hooked end of neutral wire (white or center) (D) of direct wire cable under center terminal block screw (B), hook facing right. Squeeze hooked end together. Tighten screw.
4. Connect remaining wires
Diagram shows the terminal block with remaining wires connected to outer screws.
Place hooked ends of remaining direct wire cable wires under outer terminal block screws (hooks facing right). Squeeze hooked ends together and tighten screws. Replace the terminal block cover on the back of the dryer. Tighten strain relief nut. Now, go to" Venting Requirements."
VENTING
Venting Requirements
⚠️ WARNING
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death or fire.
WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.
IMPORTANT: Observe all governing codes and ordinances. Dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, attic, crawlspace, or a concealed space of a building. Only rigid or flexible metal vent shall be used for exhausting.
Diagram shows a 4" (102 mm) heavy metal exhaust vent.
Only a 4" (102 mm) heavy metal exhaust vent and clamps may be used.
Do not use plastic or metal foil vent.
Rigid metal vent:
- Recommended for best drying performance and to avoid crushing and kinking.
Flexible metal vent: (Acceptable only if accessible to clean)
- Must be fully extended and supported in final dryer location.
- Remove excess to avoid sagging and kinking that may result in reduced airflow and poor performance.
- Do not install in enclosed walls, ceilings, or floors.
- The total length should not exceed 7 3/4 ft. (2.4 m).
- The length of flexible metal vent used must be included in the overall vent system design as shown in the "Vent System Chart."
NOTE: If using an existing vent system, clean lint from entire length of the system and make sure exhaust hood is not plugged with lint. Replace plastic or metal foil vents with rigid metal or flexible metal vents. Review “Vent System Chart" and, if necessary, modify existing vent system to achieve best drying performance.
Exhaust hoods:
- An exhaust hood should cap the vent to keep rodents and insects from entering the home.
- Must be at least 12" (305 mm) from ground or any object that may obstruct exhaust (such as flowers, rocks, bushes, or snow).
- Do not use an exhaust hood with a magnetic latch.
Recommended Styles:
Diagrams show Louvered Hood, Box Hood, and Angled Hood styles.
Elbows:
- 45° elbows provide better airflow than 90° elbows.
Diagram shows a comparison of 45° and 90° elbows, indicating 45° is better.
Clamps:
- Use clamps to seal all joints.
- Exhaust vent must not be connected or secured with screws or other fastening devices that extend into interior of duct and catch lint. Do not use duct tape.
Diagram shows examples of clamps used to seal vent joints.
Plan Vent System
Choose your exhaust installation type
Diagram shows a recommended exhaust installation layout with labels A through H, illustrating the path of the vent from the dryer to the exhaust outlet.
A. Dryer
B. Elbow
C. Wall
D. Exhaust hood
E. Clamps
F. Rigid metal or flexible metal vent
G. Vent length necessary to connect elbows
H. Exhaust outlet
Alternate installations for close clearances:
Venting systems come in many varieties. Select the type best for your installation. A close-clearance installation is shown below. Refer to the manufacturer's instructions.
Diagram shows an "Over-the-top installation" for close clearances, with an optional offset elbow. Mentions Over-the-Top Installation Kit Part Number 4396028.
Special provisions for mobile homes:
Exhaust vent must be securely fastened to a noncombustible portion of mobile home and must not terminate beneath the mobile home. Terminate exhaust vent outside.
Install Vent System
1. Install exhaust hood
Diagram shows installing an exhaust hood on an exterior wall, with dimensions 12" min. (305 mm) from ground and 12" min. (305 mm) from any obstruction. Caulking compound is used to seal the opening.
Install exhaust hood and use caulking compound to seal exterior wall opening around exhaust hood.
2. Connect vent to exhaust hood
Vent must fit over the exhaust hood. Secure vent to exhaust hood with 4" (102 mm) clamp. Run vent to dryer location using straightest path possible. Avoid 90° turns. Use clamps to seal all joints. Do not use duct tape, screws, or other fastening devices that extend into interior of vent to secure vent, because they can catch lint.
Determine vent path:
- Select route that will provide straightest and most direct path outdoors.
- Plan installation to use fewest number of elbows and turns.
- When using elbows or making turns, allow as much room as possible.
- Bend vent gradually to avoid kinking.
- Use as few 90° turns as possible.
Determine vent length and elbows needed for best drying performance:
Use the following "Vent System Chart" to determine type of vent material and hood combinations acceptable to use.
NOTE: Do not use vent runs longer than those specified in "Vent System Chart." Exhaust systems longer than those specified will: Shorten life of dryer. Reduce performance, resulting in longer drying times and increased energy usage.
The "Vent System Chart" provides venting requirements that will help achieve best drying performance.
| Number of 90° elbows | Type of vent | Box/louvered hoods | Angled hoods |
|---|---|---|---|
| 0 | Rigid metal | 90 ft. (27.4 m) | 80 ft. (24.4 m) |
| 1 | Rigid metal | 80 ft. (24.4 m) | 70 ft. (21.3 m) |
| 2 | Rigid metal | 70 ft. (21.3 m) | 60 ft. (18.3 m) |
CONNECT VENT
⚠️ WARNING
Excessive Weight Hazard
Use two or more people to move and install dryer. Failure to do so can result in back or other injury.
1. Connect vent to exhaust outlet
Diagram shows connecting the dryer's exhaust outlet to the vent hose using a clamp.
Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure vent is clean. Dryer vent must fit over dryer exhaust outlet and inside exhaust hood. Check that vent is secured to exhaust hood with a 4" (102 mm) clamp.
LEVEL DRYER
1. Level dryer
Diagram shows a level being placed on top of the dryer to check for levelness. Three illustrations show "Not Level" and "LEVEL" states.
Check levelness of dryer from side to side. Repeat from front to back.
NOTE: The dryer must be level for the moisture sensing system to operate correctly.
2. Adjust leveling legs
Diagram shows adjusting the dryer's leveling legs using a wrench, with a wood block for propping.
If dryer is not level, prop up using a wood block, use wrench to adjust legs up or down, and check again for levelness. Once dryer is level, make sure all four legs are snug against the floor and dryer does not rock.
2. Move dryer to final location
Diagram shows a dryer being moved into its final position.
Move dryer to final location, taking care not to crush or kink vent. After dryer is in place, remove corner posts and cardboard from under dryer.
COMPLETE INSTALLATION CHECKLIST
- Check that all parts are now installed. If there is an extra part, go back through steps to see what was skipped.
- Check that you have all of your tools.
- Dispose of/recycle all packaging materials.
- Check dryer's final location. Be sure vent is not crushed or kinked.
- Check that dryer is level. See "Level Dryer."
- Remove film on console and any tape remaining on dryer.
- Wipe dryer drum interior thoroughly with a damp cloth to remove any dust.
- Read "Using Your Dryer."
- For power supply cord installation, plug into a grounded outlet. For direct wire installation, turn on power.
- Set the dryer on an Auto Dry Cotton/Linen cycle. Do not use Timed Dry cycles.
If dryer will not start, check the following:
- Controls are set in a running or “On” position.
- Start button has been pushed firmly.
- Dryer is plugged into an outlet and/or electrical supply.
- Household fuse is intact and tight, or circuit breaker has not tripped.
- Dryer door is closed.
NOTE: You may notice an odor when dryer is first heated. This odor is common when heating element is first used. The odor will go away.
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.whirlpool.com/product_help - for assistance and to possibly avoid a service call.
| If you experience | Possible Causes | Solution |
|---|---|---|
| Dryer Operation Dryer will not run | Door not closed completely. START button not pressed firmly or held long enough. | Make sure the dryer door is closed completely. Press and hold the START button 2–5 seconds. |
| Household fuse is blown or circuit breaker has tripped. | There may be 2 household fuses or circuit breakers for the dryer. Check that both fuses are intact and tight, or that both circuit breakers have not tripped. Replace the fuses or reset the circuit breaker. If the problem continues, call an electrician. | |
| Incorrect power supply. | Electric dryers require 240-volt power supply. Check with a qualified electrician. | |
| Dryer will not heat | Wrong type of fuse. | Use a time-delay fuse. |
| Household fuse is blown or circuit breaker has tripped. | The drum may be turning, but you may not have heat. Electric dryers use 2 household fuses or circuit breakers. Replace the fuses or reset the circuit breaker. If the problem continues, call an electrician. | |
| Incorrect power supply. | Electric dryers require 240-volt power supply. Check with a qualified electrician. | |
| Unusual Noise Thumping noise | Dryer hasn't been used in a while. | This is normal. The thumping sound should diminish after a few minutes of use. |
| Rattling or vibrating noise | A small object caught between the edges of dryer drum. | Check the front and rear edges of the drum for small objects. Clean out pockets before laundering. |
| Dryer isn't properly leveled. | The dryer may vibrate if not properly installed. See "Level Dryer." All four dryer feet should be in firm contact with the floor. | |
| Clothing is balled up in dryer. | When balled up, the load will bounce, causing the dryer to vibrate. Separate the load items and restart the dryer. |
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.whirlpool.com/product_help - for assistance and to possibly avoid a service call.
| If you experience | Possible Causes | Solution |
|---|---|---|
| Dryer Results Clothes are not drying satisfactorily or drying times are too long | Lint screen is clogged with lint. | Clean lint screen before each load. |
| The exhaust vent or outside exhaust hood is clogged with lint, restricting air movement. | Run the dryer for 5–10 minutes. Hold your hand under the outside exhaust hood to check air movement. If you do not feel air movement, clean exhaust system of lint or replace exhaust vent with heavy metal or flexible metal vent. See "Venting." | |
| The exhaust vent is not the correct length. | Check that the exhaust vent is not too long or has too many turns. Long venting will increase drying times. See "Venting." | |
| The exhaust vent diameter is not the correct size. | Use 4" (102 mm) diameter vent material. | |
| The load is too large and heavy to dry quickly. | Separate the load to tumble freely. | |
| Fabric softener sheets are blocking the grille. | The air outlet grille is just inside the door, behind the lint screen. Check that it is not blocked by a fabric softener sheet. Use only one fabric softener sheet, and use it only once. | |
| The dryer is located in a room with temperature below 45°F (7°C). | Proper operation of dryer cycles requires temperatures above 45°F (7°C). | |
| The dryer is located in a closet. | Closet doors must have ventilation openings at the top and bottom of the door. The front of the dryer requires a minimum of 1" (25 mm) of airspace, and, for most installations, the rear of the dryer requires 5 1/4" (133 mm). See "Location Requirements." | |
| Cycle time is too short | The load may not be contacting the sensor strips on Sensor Cycles. | Level the dryer. See "Level Dryer." All four dryer feet should be in firm contact with the floor. |
| The sensor cycle is ending early. | Change the dryness level setting on Sensor Cycles. Increasing or decreasing the dryness level will change the amount of drying time in a cycle. If loads are consistently ending too early, see also "Cycle Guide – Sensor Dry Cycles.” | |
| Lint on load | Lint screen is clogged with lint. | Clean lint screen before each load. |
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.whirlpool.com/product_help - for assistance and to possibly avoid a service call.
| If you experience | Possible Causes | Solution |
|---|---|---|
| Dryer Results (cont.) Stains on load | Improper use of fabric softener. | Add dryer fabric softener sheets at the beginning of the cycle. Fabric softener sheets added to a partially dried load can stain your garments. |
| Stains on drum | Loose dyes in clothes. | Drum stains are caused by dyes in clothing (usually blue jeans). These will not transfer to other clothing. |
| Loads are wrinkled | The load was not removed from dryer at the end of the cycle. | Refer to garment care label instructions. Dry clean only garments are not recommended. |
| The dryer was tightly packed. | Dry smaller loads that can tumble freely. | |
| Odors | Recent painting, staining, or varnishing in the area where your dryer is located. | Ventilate the area. When the odors or fumes are gone from the area, rewash and dry the clothing. |
| Load too hot | Load removed before cool down portion of cycle complete. | Allow the dryer to complete the cool down portion of the cycle before removing the load. |
| Using Timed Dry cycle with a normal temperature setting. | Select a Sensor cycle with a lower heat setting to avoid overdrying the load. |
WHIRLPOOL CORPORATION LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is installed, operated, and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for Factory Specified Replacement Parts and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased.
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. Service must be provided by a Whirlpool designated service company. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the country in which it was purchased. This limited warranty is effective from the date of original consumer purchase. Proof of original purchase date is required to obtain service under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
- Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.
- Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair house fuses, or to correct house wiring or plumbing.
- Service calls to repair or replace appliance light bulbs, air filters, or water filters. Consumable parts are excluded from warranty coverage.
- Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.
- Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.
- Pick up and delivery. This major appliance is intended to be repaired in your home.
- Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
- Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an authorized Whirlpool servicer is not available.
- The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with Whirlpool published installation instructions.
- Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or cannot be easily determined.
The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.
If you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve the problem after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.
10/11
Keep this book and your sales slip together for future reference. You must provide proof of purchase or installation date for in-warranty service.
Write down the following information about your major appliance to better help you obtain assistance or service if you ever need it. You will need to know your complete model number and serial number. You can find this information on the model and serial number label located on the product.
Dealer name _____________________________________________ Address __________________________________________________ Phone number____________________________________________ Model number ____________________________________________ Serial number ____________________________________________ Purchase date ____________________________________________
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check "Troubleshooting" or visit www.whirlpool.com. It may save you the cost of a service call. If you still need help, follow the instructions below.
When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request.
If you need replacement parts or to order accessories
We recommend that you use only FSP® Factory Specified Parts. These parts will fit right and work right because they are made with the same precision used to build every new WHIRLPOOL® appliance.
To locate FSP® replacement parts, assistance in your area, or accessories:
Whirlpool Corporation
Customer eXperience Centre
1-800-253-1301
www.whirlpool.com
or call your nearest designated service center or refer to your Yellow Pages telephone directory.
Our consultants provide assistance with
- Use and maintenance procedures.
- Accessory and repair parts sales.
- Referrals to local dealers, repair parts distributors, and service companies. Whirlpool designated service technicians are trained to fulfill the product warranty and provide after-warranty service, anywhere in the United States and Canada.
For more assistance
You can write with any questions or concerns at:
Whirlpool Corporation
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
W10557652B
®/TM © 2013 Whirlpool. All rights reserved.
10/13
