Hover-1 Switch H1-SWCH Operation Manual

Important Safety Information

⚠️ WARNING! PLEASE READ THE USER MANUAL THOROUGHLY. Failure to follow the basic instructions and safety precautions listed in this manual can lead to damage to your Switch, other property damage, serious bodily injury, and even death.

All users are responsible for any consequences caused by violating warning contents or prompt operations. Hover-1 cannot be held liable.

Helmet Safety

HELMETS SAVE LIVES! Always wear a properly fitted helmet that complies with CPSC or CE safety standards when you ride your scooter.

• Correct Fitting: Make sure your helmet covers your forehead.
• Incorrect Fitting: A forehead that is exposed is vulnerable to serious injury.

General Precautions

• Use only the supplied charger with this scooter.
• Charger Manufacturer: SHENZHEN HYLETON TECHNOLOGY CO.,LTD, Model: HLT-118C-2941000
• Charger operating temperature: 32°F-104°F (0-40° C).
• Switch operating temperature: 32°F-104°F (0-40° C).
• Do not ride on icy or slippery surfaces.
• Read the operation manual and warning labels before riding.
• Store the Switch in a dry, ventilated environment.
• When transporting the Switch, avoid violent crashes or impact.

Low Temperature Warning

Low temperatures affect lubrication, increasing internal resistance and decreasing battery discharge capacity. Use caution in cold temperatures (below 40 degrees F), as this may increase the risk of mechanical failures, damage, serious bodily injury, and even death.

Safety Instructions

• Keep the Switch away from heat sources, direct sunlight, humidity, water, and other liquids.
• Do not operate if exposed to water, moisture, or other liquids to prevent electric shock, explosion, or injury.
• Do not use if dropped or damaged.
• Repairs to electrical equipment should only be performed by the manufacturer. Improper repair voids the warranty and may cause serious risk.
• Do not puncture or harm the exterior surface.
• Keep the Switch free from dust and lint.
• Do not use for anything other than its intended purpose.
• This product is not a toy. Keep out of reach of children.
• Do not expose batteries to excessive heat, direct sunlight, or open flame.
• Keep hands, feet, hair, body parts, clothing, or similar articles away from moving parts, wheels, or drive-train while the Switch is running.
• Do not operate until all instructions, warnings, and safety features are understood.
• Check with your doctor if you have a medical condition that could affect your ability to use the Switch.
• Persons with head, back, or neck ailments or prior surgeries are not recommended to use this Switch.
• Do not operate if pregnant or have a heart condition.
• Persons with any mental or physical conditions that may make them susceptible to injury or impair their ability to understand and perform safety instructions should not use the Switch.

Symbol Key

• ? NOTES: Indicates instructions or relevant facts to remember.
• ❗ CAUTION!: Indicates a hazardous situation which, if not avoided, can cause minor or moderate injury.
• ⚠️ WARNING!: Indicates a hazardous situation which, if not avoided, can cause death or serious injury.

SERIAL NUMBER: Please keep the serial number on file for warranty claims and proof of purchase.

⚠️ WARNING! Prolonged Exposure to UV Rays, Rain and the Elements May Damage the Enclosure Materials. Store Indoors When Not in Use.

Introduction

The Switch is a personal transporter. Its technology and production processes are developed with strict testing. Operating the Switch without following this manual may lead to damage or bodily injury. This manual provides information for safe operation and maintenance.

Package Contents

• Hover-1 Switch Electric Skateboard
• Scooter Assembly
• Remote
• USB Cable
• Operation Manual
• Wall Charger
• Toolkit

Scooter Components

Diagram Description: A drawing of the scooter attachment with numbered parts.

1. Scooter Attachment
2. Height Adjustment Latch
3. Remote Insert Slot
4. Brake Lever
5. Acceleration Lever

Skateboard Components

Diagram Description: A drawing of the skateboard deck with numbered parts.

1. Skate Deck
2. Attachable Trucks
3. Power Button
4. Charge Port
5. Brushless Hub Motor
6. Protective Sleeve

Remote Features

Diagram Description: A drawing of the remote control with numbered features.

1. Throttle/Brake
2. Power Button
3. Reverse Button
4. Pairing LED Indicator
5. Scooter Battery Indicator
6. Remote Battery Indicator
7. USB Charge Port
8. Scooter Docking Port

Specifications

⚠️ WARNING Any Switch that does not work properly can cause you to lose control and fall. Inspect the entire device thoroughly before every ride, and do not ride it until any problems have been corrected.

Parts List

Diagram Description: An illustration showing all the parts of the Hover-1 Switch, labeled A through G.

• A. Hoverboard Base+Scooter Attachment
• B. Skateboard Attachment
• C. Remote Control
• D. USB cable
• E. Wall Charger
• F. Handlebars
• G. Toolkit

Converting Your Switch

The Switch is shipped in skateboard form with the scooter attachment separate. Follow these instructions to convert it into a scooter.

Replacing the Front Wheels

Diagram Description: Two images showing the underside of the skateboard deck. The first shows pressing a release lever and sliding the front wheel assembly off. The second shows the front wheel assembly removed.

On the underside of the skateboard, press and hold the release lever behind the front axle, then slide the front wheel assembly away from the skateboard deck.

Attaching the Scooter Assembly

Diagram Description: Two images showing the skateboard deck. The first shows the scooter assembly being aligned with the front of the deck. The second shows the scooter assembly attached and locked.

Insert the scooter assembly into the same location on the skateboard deck. Press and hold the release lever while sliding the scooter assembly into place. Be sure the release lever is securely locked.

Insert the Remote

Diagram Description: Two images showing the top of the scooter assembly. The first shows the remote being inserted into a slot. The second shows the remote fully inserted.

Insert the remote into the top of the scooter assembly. When using the scooter, this will act as the battery indicator and enable the throttle and brakes.

Controls and Pairing

Adjust Bridge

Diagram Description: An illustration of the underside of the skateboard deck showing a wrench being used to adjust a component.

Use the wrench to rotate it clockwise to make it hard and counter clockwise to make it soft.

Attaching the Handlebars

Diagram Description: An illustration of the scooter's handlebar stem with arrows indicating clockwise and counter-clockwise rotation for attachment.

Attach the handlebars by placing them into the appropriate sockets and twisting them in the correct direction.

Turning Your Device On/Off

Power ON: Take the skateboard out of the box and place it flat on the floor. Press the power button (located on the underside of your device). The skateboard should beep once, indicating the device is powered on.

Diagram Description: An image of two buttons on the underside of the device, labeled 'POWER' and 'CHARGING'.

Power OFF: Press the power button.

Pair the Remote with the Switch

1. Power on the Skateboard.
2. Press and hold the power button for 5 seconds until you hear the skateboard beep. This indicates it is in pairing mode.
3. On the remote, press and hold the power button for 3 seconds to enter pairing mode. The indicator light will change from solid green to flashing green. This indicates successful pairing. The skateboard will stop beeping when pairing is complete.

Diagram Description: Three sequential images illustrating the pairing process: 1. Turning on the skateboard and holding the power button. 2. Turning on the remote and holding the power button. 3. Both LEDs flashing, indicating pairing is complete.

4. If pairing is unsuccessful, turn both the skateboard and the remote off and repeat the steps.

Switch Battery Indicator

The Switch battery indicator is located on the Remote. Press the power button on the Remote once to see the battery levels of your Skateboard/Scooter.

• 3 Red Dots: Battery level is between 100-70%.
• 2 Red Dots: Battery level is between 70-40%.
• 1 Red Dot with Sunburst: Battery level is between 40-10%. If the battery is lower than 10%, the light will begin flashing and must be charged immediately.

Remote Battery Indicator

The Remote battery indicator is located on the Remote itself. The LED light indicates battery levels for the remote.

• Flashing Light: Battery level is below 25% and the remote should be charged.

Before Riding

⚠️ WARNING Any Switch that does not work properly can cause you to lose control and fall. Do not ride a Switch with a part that is damaged; replace the damaged part before riding.

It is important to fully understand all elements of your Switch. Incorrect use can lead to loss of control. Learn the functions of the various mechanisms before riding.

Practice using the Switch at slower speeds in a flat, open area before riding in public areas.

Pre-Ride Checklist

• Ensure your Switch is in proper working order each time you ride. If a part does not function correctly, contact Customer Support.
• Ensure the battery is fully charged before riding.
• If the Switch is not used for an extended period, recharge the battery every 2 months to maintain battery life.
• Wear appropriate safety and protective gear.
• Wear comfortable clothes and flat closed-toe shoes.
• Carefully read the Operation Manual for working principles and tips.

Safety Precautions

The first rule in safe riding is to use common sense. Be aware of and comply with local laws governing riding on public roads.

• Always wear a helmet that meets CPSC or CE safety standards.
• Obey all local traffic laws (red/green lights, stop signs, etc.).
• Ride with the traffic, not against it.
• Ride defensively; expect the unexpected.
• Give pedestrians the right-of-way.
• Do not ride too close to pedestrians; alert them if you intend to pass.
• Slow down at intersections and look both ways before crossing.

Your Switch is not equipped with reflectors. Riding in low visibility conditions is not recommended.

If riding in low-visibility conditions (fog, dusk, night), wear bright, reflective clothing.

⚠️ WARNING When you ride in low-visibility conditions, you might be difficult to see, which could lead to a collision. Wear bright, reflective clothing in poor lighting conditions.

Safety Checklist

• Do not ride above your skill level. Ensure you have practiced with all functions.
• Do not ride too fast; increased speed comes with increased risk.
• Do not ride with pets.
• Before stepping on, ensure the Switch is on a flat, level surface with power on.
• Do not try to open or modify your Switch; this voids the warranty and may cause failure, injury, or death.
• Do not use the Switch in a manner that would put people or property in danger.
• If riding with friends, maintain a safe distance to prevent collisions.
• Keep your feet on the scooter at all times.
• Do not operate under the influence of drugs and/or alcohol.
• Do not operate when restless or sleepy.
• Use your best judgment to avoid dangerous situations.
• Do not ride off curbs, ramps, or in skate parks, empty pools, or similar areas. Misuse voids the warranty and may lead to injury or damage.
• Do not abuse your Switch; this can damage the unit and cause system failure. Physical abuse, including dropping, voids the warranty.
• Do not operate in or near puddles of water, mud, sand, stones, gravel, debris, or rough terrain.
• The Switch is intended for paved, flat, and even surfaces. Lift over uneven pavement.
• Do not ride in inclement weather (snow, rain, hail, ice) or extreme heat or cold.
• Bend your knees on bumpy or uneven pavement to absorb shock and vibration.
• If unsure about terrain safety, step off and carry your Switch. ALWAYS BE ON THE SIDE OF CAUTION.
• Do not attempt to ride over bumps or objects greater than 1/2 inch.
• PAY ATTENTION to your surroundings, road conditions, people, property, and objects.
• Do not operate in crowded areas.
• Operate with extreme caution indoors, especially around people, property, and narrow spaces.
• Do not operate while talking, texting, or looking at your phone.
• Do not ride where it is not permitted.
• Do not ride near motor vehicles or on public roads.
• Do not travel up or down steep hills.
• The Switch is intended for a single individual; DO NOT operate with two or more people.
• Do not carry anything while riding.
• Individuals with lack of balance should not attempt to operate.
• Pregnant women should not operate the Switch.
• Young children and the elderly should not operate the Switch.
• At higher speeds, consider longer stopping distances.
• Do not attempt to jump on or off your Switch.
• Do not attempt stunts or tricks.
• Do not ride in dark or poorly lit areas.
• Do not ride near or over potholes, cracks, or uneven pavement.
• Do not operate your Switch off-road.
• Do not turn sharply, especially at high speeds.
• Do not exceed maximum or minimum weight limits.
• Avoid driving in unsafe places, including areas with flammable gas, steam, liquid, or dust, which could cause fire and explosion accidents.
• Do not operate near swimming pools or other bodies of water.

⚠️ WARNING: To reduce the risk of injury, adult supervision is required. Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water; always wear shoes, and never allow more than one rider.

Riding Your Switch

FAILURE TO FOLLOW ANY OF THE FOLLOWING SAFETY PRECAUTIONS CAN AND MAY LEAD TO DAMAGE TO YOUR SWITCH, VOID YOUR MANUFACTURER WARRANTY, LEAD TO PROPERTY DAMAGE, CAUSE SERIOUS BODILY INJURY, AND CAN LEAD TO DEATH.

Operating Your Switch

• Ensure the Switch is fully charged before first use.
• Before turning on, ride it like a normal kick scooter or skateboard to get comfortable.
• When comfortable, power it on. For the motor to activate, start riding and then push the throttle down.
• To slow down, push the electric brake down. This will stop the motor and slow you down.
• The Switch is equipped with a built-in 90 Watt Brushless Motor for acceleration (up to 9 mph) and deceleration.
• To turn, use the handlebars or lean gently in the direction you wish to turn.
• The Switch can be operated manually if you do not wish to use the motor.
• As you get comfortable, maneuvering becomes easier. At higher speeds, shift your weight to overcome centrifugal force.
• Bend your knees if you encounter bumps or uneven surfaces, then dismount and carry your Switch to a safe operating surface.

⚠️ WARNING Do not turn sharply or at high speeds to avoid danger. Do not turn or ride quickly along slopes, as it may cause injury.

Weight and Speed Limitations

• Maximum Weight: 132 lbs
• Minimum Weight: 44 lbs
• Maximum Speed: Up to 9 mph (used as an e-scooter)

⚠️ WARNING Overweight exertion on the Switch may increase the possibility of injury or product damage.

Operating Range

The Switch can travel up to 6 miles on a fully charged battery in ideal conditions. Factors affecting range include:

• Terrain: Riding distance is highest on smooth, flat surfaces. Uphill or rough terrain reduces distance.
• Weight: Lighter users have further range than heavier users.
• Ambient temperature: Ride and store under recommended temperatures for increased distance, battery life, and performance.
• Speed and Riding Style: Moderate, consistent speed maximizes distance. High speeds, frequent starts/stops, idling, and frequent acceleration/deceleration decrease distance.

Safety Alerts

If a system error or illegal operation occurs, the Switch will prompt the user. These alerts should not be ignored.

• Prohibited riding surfaces (uneven, too steep, unsafe, etc.)
• Battery voltage is too low.
• The Switch is still charging.
• Overheating, or motor temperature is too high.
• If the system enters protection mode, the alarm indicator will light up (typically when battery is low).
• If the motor is blocked, the Switch will stop after 3 seconds.
• When battery level depletes below protection mode, the motor will power off after 15 seconds.
• Sustaining high discharge current (e.g., steep slope) may cause the motor to power off after 15 seconds.

Charging Your Switch

• Ensure the charging port is clean and dry, with no dust or debris.
• Plug the charger into a grounded wall outlet.
• Connect the cable with the power supply (100V ~ 240V; 50/60 Hz).
• Align and connect the 1-pin charging cable into the charging port. DO NOT FORCE OR BEND THE CHARGING CABLE, AS IT MAY CAUSE THE PRONGS TO BEND OR BREAK.
• The charging indicator light should turn RED, indicating charging is in progress.
• When the RED indicator light turns GREEN, the Switch is fully charged.
• A full charge may take up to 2.5 hours.
• After fully charging, unplug the charger from the Switch and the power outlet.

Battery Care / Maintenance

Battery Specifications

• Battery Type: Rechargeable lithium-ion battery
• Charge Time: Up to 2.5 hours
• Voltage: 25.2V
• Initial Capacity: 2.0 Ah
• Working Temperature: 32°F - 104°F
• Charging Temperature: 32°F - 104°F
• Storage Time: 1 year
• Storage Temperature: -4°F - 77°F
• Storage Humidity: 5% - 95%

Battery Maintenance

• The lithium-ion battery is built-in. Do not disassemble the Switch to remove or separate the battery.
• When charging, use the enclosed 1-pin charging cable or ensure battery charging conditions are met.
• Do not connect the Switch or battery to a power supply plug or car's cigarette lighter.
• Do not place the Switch or batteries near fire or direct sunlight. Heating can cause breaking or ignition.
• Do not continue charging if the battery does not recharge within the specified time; this may cause it to become hot, rupture, or ignite.

To preserve natural resources, please recycle or dispose of batteries properly. This product contains lithium-ion batteries. Consult your local waste authority for information regarding recycling and disposal options.

⚠️ WARNING Failure to follow the safety precautions listed below could lead to serious bodily injury and/or death.

• Do not attempt to modify, change, or replace your battery.
• Do not use if the battery emits odor, overheats, or leaks.
• Do not touch leaking materials or breathe fumes.
• Do not allow children and animals to touch the battery.
• The battery contains dangerous substances; do not open or insert anything into it.
• Please only use the charger provided by Hover-1.
• Do not attempt to charge if the battery has discharged or emits substances. Immediately distance yourself from the battery in case of fire or explosion.
• Lithium-ion batteries are hazardous materials. Follow all local, state, and federal laws regarding recycling, handling, and disposing of them.

⚠️ WARNING SEEK IMMEDIATE MEDICAL ASSISTANCE IF YOU ARE EXPOSED TO ANY SUBSTANCE THAT IS EMITTED FROM THE BATTERY.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC Instructions for a Class B Digital Device or Peripheral

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Care & Maintenance

• Do not expose the Switch to liquid, moisture, or humidity to avoid damage to internal circuitry.
• Do not use abrasive cleaning solvents.
• Do not expose to extremely high or low temperatures, as this will shorten the life of the Switch, destroy the battery, and/or distort plastic parts.
• Do not dispose of the Switch in fire, as it may explode or combust.
• Do not expose the Switch to contact with sharp objects, as this will cause scratches and damage.
• Do not let the Switch fall from high places, as this may damage internal circuitry.
• Do not attempt to disassemble the Switch, aside from swapping the front assembly.
• Use only the charger provided by Hover-1.

⚠️ WARNING Avoid using water or other liquids for cleaning. If water or other liquids enter the Switch, it will cause permanent damage to the internal components.

⚠️ WARNING Users who disassemble the Switch scooter without permission will void the warranty.

Warranty

For warranty information, please visit: www.hover-1.com

Manufacturer: DGL Group, Ltd.
195 Raritan Center Parkway Edison, NJ 08837, USA

Affix Serial Number Label Here:

[Space for Serial Number Label]