35" Sintered Stone Bar Table & Bar Stool Assembly Instructions
35" Sintered Stone Bar Table
Before Assembly
- Please read these instructions carefully before starting assembly. We suggest you carry out the assembly on a soft surface like a carpet, so as to avoid scratching the paint. Keep children away during assembly. This item contains small parts which can be swallowed by children.
- This product was made for the explicit purpose of providing outdoor function and is not to be used as a toy. This product is for residential use only. This product is NOT intended for commercial use; unintended use will void the warranty.
- This product is not intended for use during inclement or severe weather, that includes but is not limited to rain, hail, sleet, snow, wind, freezing conditions and extreme heat.
- Please note because of the nature of cast metal, you may find roughness on the surface which enhances the beauty of the product and is not a defect.
- Aluminum is soft metal, please do not use power tools, and over tighten may strip threads or break the parts.
- When not in use, store and/or cover the product in a cool dry location. Do not locate the product near any sort of high heat. Do not use the product as a support.
- Children under the age of 10, who are near the product, should be supervised by a competent adult at all times.
- Do not discard any of packaging until you finish the assembly. Keep the assembly instructions for future reference or warranty.
Parts List
| Part ID | Name | Description/Visual |
|---|---|---|
| AX4 | Leg | [Image of a table leg, labeled DX8] |
| BX1 | Table Top | [Image of a square table top, labeled EX8] |
| CX8 | Washer | [Image of a washer, labeled FX8] |
| Spring Washer | [Image of a spring washer, labeled GX1] | |
| HX1 | Bolt(M8*40) | [Image of a bolt, M8*40 size, labeled HX1] |
| Bolt Cap | [Image of a bolt cap] | |
| Umbrella Hole Cover | [Image of a circular cover for the table's umbrella hole] | |
| Wrench | [Image of an Allen wrench] |
Assembly Steps
Step 1: Attach Legs
Place all parts on a clean, soft surface. Identify parts and hardware. Turn the Table Top (B) upside down on a flat surface. Assemble Leg (A) to Table Top (B) using parts (C, D, E, F) as shown in Figure 1. Assemble the other three legs similarly. Tighten all Bolts (E) loosely at this stage. Repeat for all four legs.
[Figure 1: Shows the table top (B) upside down. Four legs (A) are being attached to the underside using bolts (E) and washers (C, D, F). The quantity 'X4' is indicated.]
Step 2: Finalize Assembly
Turn the table upright. Check that all parts are securely connected and tighten all screws fully. Adjust the levelers on the legs until the table is stable. Place the Umbrella Hole Cover (G) over the hole. Your table is now ready for use.
[Figure 2: Shows the assembled table upright. An arrow indicates the Umbrella Hole Cover (G) being placed onto the table top.]
Warning
For enhanced stability, it is strongly recommended to use a properly weighted umbrella base. Always close the umbrella during strong winds to ensure safety and prevent tipping.
Bar Stool (Model OE-H-575)
Before Assembly
- Please read these instructions carefully before starting assembly. We suggest you carry out the assembly on a soft surface like a carpet, so as to avoid scratching the paint. Keep children away during assembly. This item contains small parts which can be swallowed by children.
- This product was made for the explicit purpose of providing outdoor function and is not to be used as a toy. This product is for residential use only. This product is NOT intended for commercial use; unintended use will void the warranty.
- This product is not intended for use during inclement or severe weather, that includes but is not limited to rain, hail, sleet, snow, wind, freezing conditions and extreme heat.
- Please note because of the nature of cast metal, you may find roughness on the surface which enhances the beauty of the product and is not a defect.
- Aluminum is soft metal, please do not use power tools, and over tighten may strip threads or break the parts.
- When not in use, store and/or cover the product in a cool dry location. Do not locate the product near any sort of high heat. Do not use the product as a support.
- Children under the age of 10, who are near the product, should be supervised by a competent adult at all times.
- Do not discard any of packaging until you finish the assembly. Keep the assembly instructions for future reference or warranty.
Parts List
| Part ID | Name | Description/Visual |
|---|---|---|
| AX2 | Back | [Image of the stool backrest, labeled EX20] |
| BX2 | Seat | [Image of the stool seat, labeled FX20] |
| CX2 | Front Leg | [Image of a front leg assembly, labeled GX12] |
| DX2 | Support Bar | [Image of a support bar, labeled HX8] |
| IX20 | Spring Washer | [Image of a spring washer, labeled IX20] |
| JX2 | Washer | [Image of a washer, labeled JX2] |
| KX2 | Bolt(M6*20) | [Image of a bolt, M6*20 size, labeled KX2] |
| Bolt(M6*25) | [Image of a bolt, M6*25 size] | |
| Bolt Cap | [Image of a bolt cap] | |
| Cushion | [Image of a seat cushion] | |
| Allen Wrench | [Image of an Allen wrench] |
Assembly Steps
Step 1: Assemble Front Legs and Seat
Place all parts on a clean, soft surface and identify them. Assemble Front Leg (C) and Seat (B) using parts (E, F, G, I) and (E, F, H, I) as shown in Figure 1. Remember not to tighten all bolts before they are fully set up.
[Figure 1: Depicts the seat (B) with front legs (C) being attached using bolts and washers (parts E, F, G, I, H, I).]
Step 2: Assemble Back and Seat
Assemble Back (A) and Seat (B) using parts (E, F, H, I) as shown in Figure 2. Remember not to tighten all bolts before they are fully set up.
[Figure 2: Shows the stool frame where the backrest (A) is being attached to the seat (B) using bolts and washers (parts E, F, H, I).]
Step 3: Assemble Support Bar
Assemble Support Bar (D) between Back (A) and Front Leg (C) using parts (E, F, G, I) as shown in Figure 3. Remember not to tighten all bolts before they are fully set up.
[Figure 3: Illustrates the stool frame with the support bar (D) being connected between the backrest (A) and front leg (C) using bolts and washers (parts E, F, G, I).]
Step 4: Finalize Assembly
Tighten all bolts securely using the Allen Wrench (K). Do not over-tighten bolts, as this may damage the product and void the warranty. Tie the Cushion (J) to the seat. Adjust the levelers on the legs until the stool is stable. Your stool is now ready for use.
[Figure 4: Shows the completed stool. An arrow indicates the cushion (J) being secured to the seat. Leveler adjustment is implied.]
