MiCODUS MV730 User Manual V2.0
Learn how to set up your new MiCODUS Tracker
1. Main Features
- GPS+GLONASS+LBS: Global Positioning System
- Remotely Cut Off /Resume Fuel: Control fuel remotely
- Historical Route Playback: Review past routes
- Realtime Tracking: Monitor current location
- 9-90V Wide Working Voltage: Compatible with various power inputs
- Vibration Alarm: Alerts upon detecting vibration
- ACC Status Detection: Detects ACC status
- Tow Alarm: Alerts if the vehicle is towed
- Power Disconnect Alarm: Alerts if power is disconnected
- Geo-fence: Set virtual boundaries
- Engine On/OFF Alarm: Alerts when the engine status changes
- Auto Arm by ACC: Automatically arms when ACC is off
- Overspeed Alarm: Alerts when exceeding speed limits
- Lifetime Free Tracking Platform: Access to a free tracking service
2. Specifications
| Device Information | Model | MV730 |
| Weight | 53g | |
| Dimensions | 31mm(L) * 31mm(W) * 57mm(H) | |
| Working Parameters | Working Voltage | DC 9-90V |
| Working Current | <30 mA | |
| Sleep Current | <15 uA | |
| Battery Capacity | 3.7V 80mAh Lion Polymer battery | |
| Working Temperature | -20 °C - 75 °C | |
| Working Humidity | 10%-85%RH non-condensing | |
| Cellular Specifications | Working Frequency | 2G GSM/GPRS: 850/900/1800/1900MHz |
| SIM Card | Nano SIM Card | |
| Cellular Antenna | Built-in | |
| GNSS Specifications | Positioning Type | GPS+GLONASS+LBS |
| GPS Antenna | Built-in | |
| Cold Start | ≤32 Seconds | |
| Hot Start | ≤1 Second | |
| Tracking sensitivity | -162 dBm | |
| GPS Channels | 64 | |
| Position Accuracy | 5-10m |
3. How to manage the tracker to get online?
Step 1: SIM Card Preparation
Please get a suitable SIM card from your local place. The SIM card must meet below points:
- It must be compatible with the 2G GSM network.
- Please enable SMS, call, and internet data traffic of the SIM card.
- Enable the caller ID display feature.
- Remove the PIN code.
- Use Nano size SIM card for the tracker.
- Please inquire the SIM card provider for the exact correct APN information.
Step 2: SIM Card Installation
A visual guide showing the steps for SIM card installation:
- Insert the SIM card into the designated slot.
- Ensure the SIM card is correctly oriented (indicated by a checkmark).
- Place the tracker into its casing.
- Connect the necessary cables.
Step 3: Wiring
A wiring diagram illustrates the connections:
- Connect the device to a 9-90V DC power source (Car Battery).
- Connect the Fuel Pump Line (Voltage: 5V-30V, Current: < 60A).
- Ensure the ON/ACC/OFF switch is correctly positioned.
NOTE: After correctly installing the SIM card, it is crucial to connect the tracker with external power no less than 12V for power supply before operation.
Step 4: Configure APN
Please get the exact correct APN name from your local SIM card provider. Take the tracker to a good signal place for operation and configure the APN for it as below:
| SMS Command Format | Reply | Example | Note |
|---|---|---|---|
| apn123456+space+apn name | apn ok | apn123456 cmnet | Please get the exact correct APN name from local SIM card provider. "cmnet" is just an example of APN name. |
| apnuser123456+space+apnuser | apnuser ok | apnuser123456 cmnet | If the SIM card operator doesn't have APN user name, then please ignore this configuration. |
| apnpasswd123456+space+apnpassword | apnpasswd ok | apnpasswd123456 123 |
Note: The APN information is very important; it must be 100% correct to match the SIM card of the tracker. If you configure the wrong APN, the tracker will reply "SET APN ok" but it will not get online!
Step 5: Indicator Status Description
| LED | Event | State |
|---|---|---|
| GSM LED (GREEN) | Searching for network | Solid |
| Network has been registered | Flash every 1 second | |
| GPS LED (Blue) | GPS is in fixing | Solid |
| GPS has fixed | Flash every 1 second | |
| ALL LED | Device is working but stopped more than 5min | |
| Device has not been turn on | ALL LED TURN OFF | |
| Device ran out of battery |
4. Package Content
- GPS Main Unit x 1
- Function Cable x 1
- Pick x 1
- Harness x 1
- User Guide x 1
- Genuine Packing Box x 1
5. Functions Explanation
Please follow with the quick user guide carefully!
a. Vibration Alert:
This vibration alert function works only under stationary status. To use this function:
- Set admin number by SMS command:
admin123456+space+mobile number with country code - Enable the device to enter into arm mode by SMS command:
111 - Configure the alarm ways by SMS command:
vibalm123456
For example:
admin123456 0086134********admin ok111arm okvibalm123456vibrate sms alarm set ok
Keep the device under stationary status for more than 5 minutes to let it enter into sleep arm mode. Vibrate the device, then the tracker will send the vibration alarm messages.
b. Cut Off Fuel/Resume Fuel
- Set admin number by SMS command:
admin123456+space+mobile number with country code - Send this SMS command from the admin number to cut off fuel:
555
For example:
admin123456 0086134********admin okcut oil ok
NOTE: Regarding the cut-off fuel function, first, please ensure the fuel circuit is connected to the main power. Second, it has 3 different performance modes; please read them carefully.
- If network and satellite signals are both available, and the equipment speed exceeds 20km/h, the fuel circuit will not be cut off immediately but intermittently until the speed drops below 20km/h, at which point it can be completely cut off.
- If the tracker has a network signal but no satellite signal, the fuel circuit will be cut off intermittently, and after 2-3 minutes, it will be cut off completely.
- If the tracker stops for more than 5 minutes, the fuel circuit will be cut off immediately and then reconnected. However, if you vibrate the tracker, the fuel circuit will be cut off immediately.
c. Engine On/Off Alarm
- Set admin number by SMS command:
admin123456+space+mobile number with country code - Configure the alarm ways via SMS command:
autorep123456,AB
Where:
- A=0 (Engine ON: No Alarm); A=1 (Engine ON: SMS only); A=2 (Engine ON: Platform only); A=3 (Engine ON: SMS+Platform)
- B=0 (Engine OFF: No Alarm); B=1 (Engine OFF: SMS only); B=2 (Engine OFF: Platform only); B=3 (Engine OFF: SMS+Platform)
For example:
admin123456 0086134********admin okset okautorep123456,12
6. Installation Recommendation
Visual representations of recommended installation locations within a car and on a scooter:
- Car: Under Front Dash, Inside Door Pedal, Inside the taillight component or plastic, Under the pedal.
- Scooter: Inside the head light, Inside the front cover.
Important Notes:
- 1) The device should face up to the sky for optimal signal reception.
- 2) Metal thermal barriers or heating layers on the windshield can affect the signal.
7. Troubleshooting
| Type | Use |
|---|---|
| Unable to connect to tracking platform | Check the APN and settings. Check whether the data service of the SIM card is enabled. Check the balance of the SIM card. |
| Tracker shows offline | Check whether external power is still connected. Check if the vehicle entered a network blind area. Check the balance of the SIM card. |
| Unable to locate | Make sure the top side is facing upward without metallic things shielded. Make sure it's not in an area with no satellite coverage. |
| Location drift | In areas with poor GNSS signal (tall buildings or basements), drifting may happen. Check whether vibration happens around to trigger the accelerator. |
| No command reply | Make sure the command format is correct. The vehicle may be in a network blind area. Make sure the SIM card is well inserted and has SMS service. |
8. Full SMS Commands List
| Functions | Command Format | Explanation |
|---|---|---|
| Set Admin Number | admin123456+space+mobile number with country code | Please add your country code as the prefix of the admin number. |
| Back to Factory Setting | begin123456 | After sending this SMS command, all your configurations will be cleared, and the device will revert to factory default settings. |
| Password Change | password+old password+space+ new password | The password can only be 6 digits. |
| Restart | rst | After sending this SMS command, the configurations will be saved, and the device will restart. |
| APN | apn+123456+apn content | Please get the exact correct APN name from the SIM card provider of the tracker. "cmnet" is China Mobile's APN name. |
| apnuser+123456+space+content | If the SIM card operator doesn't have an APN user, then please ignore this configuration. | |
| apnuser+123456+space+content | If the SIM card operator doesn't have an APN password, then please ignore this configuration. | |
| IP&Port | adminip+123456+space+ip+space+port | MiCODUS tracking platform's IP: 47.254.77.28; Port: 7700 |
| Domain | SZCS,123456,DOMAIN=d.micodus.net:7700 | MICODUS server domain: d.micodus.net, Port: 7700 |
| Google Maps Link | G123456# or where | V:A: Indicates the device has GPS signal; V:V: Indicates the device doesn't have GPS signal; 2019-11-26 10:17:01: Date and Time; S: 000km/h: Speed of the tracker; Bat:5: Battery level of the backup battery of the tracker (6 levels: "6"=100%, "5"=80%, "4"=60%, "3"=40%, "2"=20%, "1"=10%); ACC: off: Status of the car engine; 7201000006: ID number of the device; S26: GSM signal is 26; G06: GPS signal is 06; p:46000, 1:13152, c:63162: p,l,c these 3 parameters mean the LBS code. |
| Data Upload Frequency | upload123456+space+time | Time interval scope: 10-180s |
| Time Zone | timezone+123456+space+GMT No. | If it's an East time zone, you needn't input a sign "+". For example, if the time zone is East 8, then the SMS command should be sent like this: timezone123456 8 |
| Parameter Query | param1 | Firmware version, ID, IP, port, domain, APN |
| param2 | Admin number, SOS number, move distance, overspeed, auto arm time, auto disarm time, alarm interval | |
| Status | status | BAT:10 GPRS: GSM: GPS:A/V ACC:on/off oil:on/off power:on/off |
| Arm | 111 or SF | |
| Disarm | 000 or CF | |
| Cut Off Fuel | 555 | |
| Resume Fuel | 666 | |
| Movement Alarm | move+alarm distance | Movement alarm distance scope: 100-1000m |
| Overspeed Alarm | speed+123456+space speed limit | Overspeed alarm speed scope: 20-150km/h |
| IMEI Checking | imei+123456 | |
| Sleep Mode | sleep123456 time | If the device keeps stationary for more than 5 minutes, it will enter sleep mode automatically. SMS commands and calls can wake it up. |
| sleep123456 shock | If the device keeps stationary for more than 5 minutes, it will enter sleep mode automatically. Vibration, SMS commands, and calls can wake it up. | |
| sleep123456 off | Cancel sleep mode. | |
| Vibrate Alarm | vibx,y | x=1-3 (1: SMS alarm, 2: Call alarm, 3: SMS first then Call); y=1-9 (1 is the most sensitive) |
| vibcall+123456 | Vibrate call alarm set ok (If the device keeps stationary for more than 5 minutes, it will enter sleep mode automatically. Vibration, SMS commands, and calls can wake it up.) | |
| vibalm+123456 | Vibrate SMS alarm set ok (If the device keeps stationary for more than 5 minutes, it will enter sleep mode automatically. Vibration, SMS commands, and calls can wake it up.) | |
| Tow Alarm | towA,B | A: 1-4 (1: SMS alarm, 2: Call alarm, 3: SMS+Call, 4: Platform alarm); B: Distance (500-10000m) |
| Auto Arm By ACC | acclt,time | Time scope: 5-1200 seconds |
| Engine On/Off Alarm | autorep123456,AB | A=0 (Engine ON: No Alarm); A=1 (Engine ON: SMS only); A=2 (Engine ON: Platform only); A=3 (Engine ON: SMS+Platform); B=0 (Engine OFF: No Alarm); B=1 (Engine OFF: SMS only); B=2 (Engine OFF: Platform only); B=3 (Engine OFF: SMS+Platform) |
9. Any Questions?
E-mail: support@micodus.com
Skype: MICODUS
10. Download the APP
Search "MICODUS" in the iOS App Store or Google Play Store, or scan the QR code below to download the MICODUS APP:
[QR Code Placeholder for App Download]
File Info : application/pdf, 10 Pages, 5.00MB
DocumentDocumentReferences
Related Documents
 |
MiCODUS ML150 User Manual V1.0: Setup and Features Comprehensive user manual for the MiCODUS ML150 GPS Tracker, covering setup, specifications, functions, applications, troubleshooting, and SMS commands. |
 |
MiCODUS MV810G 4G GPS Tracker User Manual - Setup and Features Comprehensive user manual for the MiCODUS MV810G 4G GPS tracker. Learn how to set up, configure, and use its features, including real-time tracking, geofencing, alarms, and SMS commands. |
 |
MiCODUS MP90G User Manual: Setup, Features, and SMS Commands Comprehensive user manual for the MiCODUS MP90G GPS tracker. Learn how to set up, activate, and utilize its features like real-time tracking, SOS alerts, voice monitoring, and various alarm settings through detailed instructions and SMS commands. |
 |
MiCODUS ML150 User Manual V1.0: Setup and Features Comprehensive user manual for the MiCODUS ML150 tracker, detailing setup, specifications, functions, applications, and troubleshooting. Learn how to configure working modes, alerts, and other features for optimal tracking. |
 |
MiCODUS MV33 Tracker User Manual V2.0 Comprehensive user manual for the MiCODUS MV33 Tracker, covering features, specifications, activation, configuration, functions, installation, troubleshooting, and SMS commands. |
 |
MiCODUS MV66 User Manual V1.0: Setup and Operation Guide Comprehensive user manual for the MiCODUS MV66 tracker, detailing setup, specifications, features, and SMS commands for effective vehicle tracking and monitoring. |
 |
MiCODUS ML910G/ML920G GPS Tracker User Manual & Setup Guide Comprehensive user manual for MiCODUS ML910G and ML920G GPS trackers, covering setup, specifications, features, SMS commands, and troubleshooting. Learn how to activate, configure, and utilize your MiCODUS tracker. |
 |
MiCODUS 4G MV710G GPS Tracker User Manual Comprehensive user manual for the MiCODUS 4G MV710G GPS tracker, covering features, specifications, installation, troubleshooting, and SMS commands. |