1. Main Features
- ? 4G LTE + 2G GSM
- ?️ Historical Route Playback
- ? Real-time Tracking
- ? SOS
- ? Waterproof IP65
- ? Voice Monitor
- ⚡ Overspeed Alarm
- ? Vibration Alarm
- ? Geo-fence
- ? 3000mAh
2. Specifications
| Device Information | |
|---|---|
| Model | MP90G |
| Weight | 120g |
| Dimensions | 76mm(L) * 40mm(W) * 27mm(H) |
| Charging Time | Around 6 hours |
| Working Parameters | |
|---|---|
| Battery Working Time | Tracking Mode, 1 minutes' reporting: 5 days |
| Working Voltage | DC 3.4V - 4.5V |
| Working Current | 4V/Average 45mA |
| Sleep Current | 4V/less than 5mA |
| Battery Capacity | 3.7V 3000mAh Lion Polymer battery |
| Working Temperature | -20 °C - 75 °C |
| Working Humidity | 10%-85%RH non-condensing |
| Cellular Specifications | |
|---|---|
| Working Frequency | 4G LTE FDD: B1/B2/B3/B4/B5/B7/B8/B28/B66 2G GSM/GPRS/EDGE: 850/900/1800/1900MHz |
| SIM Card | Micro SIM Card |
| Cellular Antenna | Built-in |
| GNSS Specifications | |
|---|---|
| Positioning Type | GPS+BEIDOU+LBS |
| GPS Antenna | Built-in |
| Cold Start | ≤32 Seconds |
| Hot Start | ≤1 Second |
| Tracking sensitivity | -162 dBm |
| GPS Channels | 64 |
| External Interface | |
|---|---|
| Position Accuracy | 5-10m |
| External Interface | Microphone, SOS, Type-C Recharging |
3. Activate Device
Install the SIM card via the correct direction as below:
SIM Card Types: Nano SIM, Micro SIM, Normal SIM
Device Image Description: The device is a compact black rectangular unit with textured sides. It features a prominent circular button on the front, below which is a glossy black panel. Above the button, there are indicator lights for GPS (blue), Cellular (yellow), and Power (red). The SIM card slot is located on the side.
| LED | Event | State |
|---|---|---|
| POWER LED (RED) | Charger inserted and battery has been fully charged | Solid |
| Charger has not been inserted | Dark | |
| CELL LED (YELLOW) | Searching for network | Dark |
| Network has been registered | Flash every 1 second | |
| GPS LED (BLUE) | GPS is in fixing | Solid |
| GPS has fixed | Flash every 1 second | |
| ALL LED | Device is working but stopped more than 5min | Solid |
| Device has not been turn on | ALL LED TURN OFF | |
| Device ran out of battery | ALL LED TURN OFF |
Please get the exact correct APN name from your local SIM card provider. Take the tracker to a good signal place for operation and configure the APN for it as below:
| SMS Command Format | Reply | Example | Note |
|---|---|---|---|
APN,ApnName,User,Password# | SET APN OK | APN,orange,orange,orange# | If the SIM card has APN user and APN password, then use this command. |
APN,ApnName# | SET APN OK | APN,internet# | If the SIM card operator doesn't have APN user and APN password, then please use this command. |
Note: The APN information is very important; it must 100% correctly match the SIM card of the tracker. If you configure the wrong APN, the tracker will reply "SET APN ok" but it will not be able to get online.
4. Package Content
- Main Unit MP90G x 1
- Charging Cable x 1
- Screws x 4
- Screwdriver x 1
- Rubber Pad x 1
- SIM Card Slot Cover x 1
- User Guide x 1
- Genuine Packing Box x 1
5. Functions Explanation
Please follow with the quick user guide carefully!
a. Voice Monitor:
- Set center number by this sms command:
CENTER,A,center number# - Switch the tracker to voice monitor mode by this sms command:
MONITOR# - Dial the SIM number of the tracker from the center number. The tracker will pick up the call automatically, and you can remotely monitor the voice around it.
For example:
MP90G CENTER,A,12345678910#
SET CENTER NUMBER OK
MONITOR#
SET MONITOR MODE OK
b. Vibration Alert:
This vibration alert function works only under stationary status. How to use this function:
- Configure SOS numbers for the tracker by this sms command:
SOS,A,1st number,2nd number,3rd number#(Supports up to 3 SOS numbers). - Enable the device to enter into arm mode by this sms command:
ARM# - Configure the alarm ways by this sms command:
SENALM,[A][,M]#
A=ON/OFF (default: OFF);
M=0/1/2 (way of alarming: 0: GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+phone call, default:1). - Keep the device stationary for more than 5 minutes to let it enter into sleep arm mode.
- Vibrate the device, and the tracker will send the vibration alarm messages.
For example:
MP90G SOS,A,12345678910#
SET SOS NUMBER OK
ARM#
SET ARM MODE OK
SENALM,ON,1#
SET VIBRATE ALARM OK
d. Enable SOS Emergency Call:
- Set SOS alarm numbers via this sms command:
SOS,A,1st number,2nd number,3rd number# - Press the SOS panic button 3 times continuously. The SOS emergency message and call will be sent out to the SOS numbers.
For example:
MP90G SOS,A,12345678910#
SET SOS NUMBER OK
6. Applications
The MiCODUS MP90G tracker can be used in various scenarios:
- Personal: For tracking individuals, children, or elderly family members. (Image description: A tracker placed in a backpack pocket.)
- Valuables: To secure important items like safes or luggage. (Image description: A tracker placed inside a safe compartment.)
- Suitcase: For tracking luggage during travel. (Image description: A tracker placed inside a suitcase.)
- Vehicles: For tracking cars, motorcycles, or other vehicles. (Image description: A tracker discreetly placed inside a car's dashboard.)
7. Troubleshooting
| Type | Use |
|---|---|
| Unable to connect to tracking platform | Check the APN and settings. Check whether the data service of SIM card is enabled. Check the balance of SIM card. |
| Tracker shows offline | Check whether external power is still connected. Check if the vehicle entered a network blind area. Check the balance of SIM card. |
| Unable to locate | Make sure the top side is facing upward without metallic things shielded. Make sure it's not in an area with no satellite coverage. |
| Location drift | In areas with poor GNSS signal (e.g., tall buildings, basements), drifting may happen. Check whether vibration happens around to trigger the accelerator. |
| No command reply | Make sure the command format is correct. The vehicle may be in a network blind area. Make sure the SIM card is well inserted and has SMS service. |
8. Full SMS Commands List
| Functions | Command Format | Explanation |
|---|---|---|
| APN Setting | APN,Network name[,name,password]# | APN,CMNET# (if no name & Password)APN,internet,internet,internet# (if with name & Password) |
| Server Setting | If set with Domain Name: SERVER,1,Domain,Port#If set with IP: SERVER,0,IP,Port# | SERVER,1,d.micodus.net,7700#SERVER,0,47.254.77.28,7700# |
| Restore factory settings | FACTORY# | |
| Restart device | RESTART# | |
| Internet Traffic Switch | INTERNET,ON#INTERNET,OFF# | |
| Version Inquiry | VERSION# | |
| Parameter Inquiry | PARAM# | BATTERY: XX% (Built-in Battery Power Percent) INTERNET: CLOSED (No Network) FAILED (Connecting Network or Failure) SUCCESS (Connected to Network) NET: NONE (No GSM Signal), HIGH / MED / LOW (Signal Strength) 18 GPS: CLOSED (GPS Module Closed) FIXED,N (Positioned and satellite number) UNFIX,0 (Not Positioned yet) SPEED:30KM/H SENSOR: ON/OFF (Sensor on or off), LEVEL: 3 (Sensitivity level 1-9) STATE: ARM (Arm or Disarm) |
| Status Inquiry | STATUS# | ID: 19172012644 (ID number of device) STATE: ARM(DISARM)(Defense status of device) SPEED: ON/OFF(alarm status); 30km/h(alarm value); 0/1/2(alarm way) SHIFT: ON/OFF(alarm status); 300m(alarm value); 0/1/2(alarm way) VIBRATE: ON/OFF(alarm status); 3(sensitivity level); 0/1/2(alarm way) LOW BATTERY: ON/OFF(alarm status); 1/2/3 (alarm way) NOTE: Alarm Ways: 0/1/2 (0 :GPRS only, 1: SMS+ GPRS, 2 : GPRS+SMS+phone call) |
| Alarms Parameters | ALARM# | |
| Latitude & Longitude Inquiry | WHERE# | |
| Map URL Inquiry | URL# | |
| Time Zone Setting | GMT,Time zone orientation, Whole Time Zone[,Half Time Zone]# | GMT,E,8# (if no half time zone)GMT,W,9,30# (if has half time zone)NOTE: Parameter: E / W; 0 ~ 12; 0/15/30/45 |
| Working Mode Setting | MODE,A,T1,T2# | A=1/2/3, 1:Tracking mode, 2: Power saving mode, 3: Hibernation mode; Default mode: 1 A=1: T1: upload interval of GPS data in moving status, unit: second, 10-3600s; default: 10s T2: upload interval of GPS data in static status, unit: second, 180-65535s; default: 3600s A=2: T1: interval start time, format: HH:MM T2: time interval, range: 1-72 unit: hour, default interval: 24hours A=3: T1: interval start time, format: HH:MM T2: time interval, range: 1-72 unit: hour, default interval: 24hours Note: The difference between mode 2 and mode 3 is that in mode 2, SMS commands and phone calls can wake up the device, but vibration cannot. In mode 3, only manual restart operation can wake up the device, after that, the device will work for 5 minutes and then go to sleep. |
| Set the angle upload | ANGLEREP,[X][,A][,B]#ANGLEREP,OFF# | X=ON/OFF, default: ON; A=5~180 degrees, diversion angle degree, default: 30 degrees; B=2~5 seconds, detecting time, default: 3 seconds. |
| Mileage Statistics | MILEAGE,[A],[B]#MIELEAGE# | A=ON/OFF, On/Off mileage calculation, default: Off B=0~999999, Mileage initial value, unit: km; default: 0, mileage return to zero Query current mileage |
| Add SOS Administrator Number | SOS,A,1st number,2nd number,3rd number# | Set 3 numbers at a time:SOS,A,13800138000,13800138001,13800138002#Set the first number separately: SOS,A,13800138000#Set the second number separately: SOS,A,,13800138001#Means to set 3rd number separately: SOS,A,,,13800138002# |
| Delete SOS Administrator Number | SOS,D,1st number,2nd number,3rd number# or SOS,D,1,2,3# | Directly delete the number: SOS,D,13800138000#Delete 1st number: SOS,D,1#Delete 2nd number: SOS,D,2#Delete the 2nd and 3rd number: SOS,D,2,3# |
| Add Center Number | CENTER,A,center number# | CENTER,A,13800138000#NOTE: Center number is only used for cutting off power & oil, it can only be set by SOS Administrator when using this command by SMS. |
| Delete Center Number | CENTER,D# | |
| Sleep Mode Setting | SLEEP#SLEEP,OFF# | NOTE: After setting this sleep mode, the device will enter into sleep mode automatically when the device remains stationary for more than 5 minutes. |
| Voice Monitor Mode | MONITOR# | NOTE: Before monitoring the voice around the device, the user must change the device to this monitor mode first. |
| Track Mode | TRACK# | NOTE: After using voice monitor mode, the user can switch the device back to track mode by this command. |
| Heartbeat Packet Upload | HBT,time# | HBT,3#NOTE: Range: 1-60min, default 3min. |
| Sensor Sensitivity | SENLEVEL,sensitivity# | SENLEVEL,2#NOTE: Sensitivity Level: 1-9 (1-9 is from weak to strong vibration) |
| Vibration Alarm Setting | SENALM,[A][,M]#SENALM,OFF# | A=ON/OFF; default:ON M=0/1/2, way of alarming, 0: GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+phone call, default:1 Cancel vibration alarm |
| Overspeed Alarm Setting | SPEED,[A][,B][,C]#SPEED,OFF# | A=ON/OFF, open or close over speed alarm, default: OFF B=1~255(km/h), speed limit, default: 100(km/h); C=0/1/2, way of alarm, 0: GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+CALL; default: 1 Cancel speed alarm |
| Shift Alarm Setting | SHIFT,[A][,B][,M]#SHIFT,OFF# | Example: SHIFT,ON,100,1# (Means Setting 100 meters shift alarm range, when the ignition turned off, vehicle's 100 meters' shift will trigger the alarm.)A=ON/OFF; default:ON B=Shift Distance (Range: 100-9999m) M=0/1/2; way of alarm, 0: GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+CALL, default:1 Cancel shift alarm |
| Low Battery Alarm Setting | BATALM,[A][,M]#BATALM,OFF# | A=ON/OFF, default: ON; M=0/1/2, way of alarming, 0: GPRS only, 1: SMS+GPRS, 2: SMS+GPRS+Call, default:1; NOTE: Once the battery level is below 20% device will alarm. Cancel low battery alarm |
| SOS Alarm Setting | SOSALM,[A][,M]#SOSALM,OFF# | A=ON/OFF, default: ON; M=0/1/2, way of alarming, 0: GPRS only, 1: SMS+GPRS, 2: SMS+GPRS+Call, default:2; NOTE: Press the SOS button 3 times continuously to trigger the SOS alarm. And please configure SOS numbers firstly. Cancel SOS alarm |
9. Any Questions?
E-mail: support@micodus.com
Skype: MiCODUS
10. Download the APP
Search "MiCODUS" in the iOS APP store or Google Play Store to download the MiCODUS APP. You can also scan the QR code provided in the original document.
App Availability:
- Download on the App Store
- Download for Android
